N71 金属材料试验机 标准查询与下载

BS EN ISO 7500-1:2004 金属材料.静态单轴向试验机的鉴定.拉伸和压缩试验机.测力系统的鉴定和校准

This part of ISO 7500 specifies the verification of tension/compression testing machines. The verification consists of  a general inspection of the testing machine, including its accessories for the force application;  a calibration of the force-measuring system. NOTE This part of ISO 7500 addresses the static verification of the force-measuring systems. The calibration values are not necessarily valid for high-speed or dynamic testing applications. Further information regarding dynamic effects is given in the Bibliography.

Metallic materials. Verification of static uniaxial testing machines. Tension/compression testing machines. Verification and calibration of the force-measuring system

ISO 7500-1:2004 静力单轴试验机的检验.第1部分:拉力和(或)压力试验机.测力系统的检验与校准

This part of ISO 7500 specifies the verification of tension/compression testing machines. The verification consists of — a general inspection of the testing machine, including its accessories for the force application; — a calibration of the force-measuring system. NOTE This part of ISO 7500 addresses the static verification of the force-measuring systems. The calibration values are not necessarily valid for high-speed or dynamic testing applications. Further information regarding dynamic effects is given in the Bibliography.

Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Verification and calibration of the force-measuring system

KS B ISO 496:2003 驱动和被驱动机械.轴的高度

이 규격은 원동 및 종동 기계의 밀리미터 단위의 4개의 시리즈와 인치 단위의 5개의 축

Driving and driven machines-Shaft heights

KS B ISO 7500-1:2003 金属材料.静态单轴向试验机的校正.第1部分:拉伸/压缩试验机.力测量系统的检验和校正

이 규격은 인장/압축 시험기의 검증 및 교정 방법에 대하여 규정한다.검증 및 교정

Metallic materials-Verification of static uniaxial testing machines-Part 1:Tension/compression testing machines-Verification and calibration of the force-measuring system

KS B ISO 4965:2003 轴向负荷疲劳试验机.动态力校准.应变测量技术

이 규격은 시험기의 교정에 영향을 줄 수 있는 시험용 치구를 포함한 피로 시험기의 동하

Axial load fatigue testing machines－Dynamic force calibration－Strain gauge technique

KS B 5536-2002 金属材料用蠕变试验机

이 규격은 ISO 204에 따른 인장에서의 단축 크리프 시험에 사용된 시험기의 검정을 규정

Creep testing machines for tensile stress of metallic materials

BS EN ISO 9513:2002 金属材料.单轴向试验用引伸计的校准

This International Standard specifies a method for the static calibration of extensometers used in uniaxial testing. The tem "extensometer" is understood to mean the displacement measuring device and the system for indicating or recording this displacement. NOTE extensometer which have: This International Standard does not at present provide detailed guidance on the calibration of those types of - variable gauge lengths; - no contact with the test piece; - full field strain measurements devices. Special consideration should be given to such devices. These issues should be addressed at the next revision of this International Standard. However some guidance on this subject might be found in ASTM E83:1996 (see Bibliography).

Metallic materials - Calibration of extensometers used in uniaxial testing

JB/T 9397-2002 拉压疲劳试验机.技术条件

　　本标准规定了拉压疲劳试验机的技术要求、试验方法、检验规则及标志、包装、运输与贮存。 　　本标准适用于最大动态力为±1000kN，频率不超过400Hz，金属试验用电子测量、力控制式拉压疲劳试验机。本标准亦适用于应用在特殊条件(如高低温、腐蚀性介质)和带有附属装置(如程序控制装置)的试验机，但本标准对这些特殊条件和附属装置不予规定。

Specifications for tension-compression fatigue testing machines

ISO 4516:2002 金属和其他无机覆盖层.维氏和努氏显微硬度检验

This International Standard describes the application of the Vickers and Knoop micro-indentation tests for determining the microhardness of metallic and other inorganic coatings. This method is applicable where indenter forces generally need to be below 10 N such as for electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic coatings on aluminium. It is applicable to measurements normal to the coated surface as described in 7.4 and to measurements on cross-sections as described in 7.3. NOTE 1 Attention is drawn to ISO 4545, ISO 6507-1, ISO 6507-2 and ISO 6507-3, which describe Knoop and Vickers hardness testing of metallic materials. Other International Standards for instrumental indentation testing, the verification of microindentation testing instruments and for the verification of reference blocks to be used with such instruments are currently being developed (e.g. ISO 14577 Parts 1 to 4). NOTE 2 Usually for hardness measurements of coating test forces in the microhardness range in accordance with ISO 6507-1 are used. However, since the largest possible test force should be selected, test forces of the low force and hardness ranges may also be used.

Metallic and other inorganic coatings - Vickers and Knoop microhardness tests

DIN 51302-2:2000 材料试验机.拉伸.加压和弯曲试验机的检验.建筑材料压力试验机的钩检验

This draft specifies material testing machines for the additional testing of compression testing machines for building materials.

Materials testing machines - Strain cylinder test method for compression testing machines for concrete

JIS B 7727:2000 肖氏硬度试验.试验机的验定

この規格は，金属材料用のショア硬さ試験機の間接検証方法について規定する。

Shore hardness test -- Verification of testing machines

DIN EN ISO 7500-1 Bb.2:1999 金属材料.静态单轴压缩试验机的验证.第1部分:拉伸/压缩试验机.测力系统的验证与校准.弹簧试验机的要求、验证和校准一般规则

Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines; verification and calibration of the force-measuring system; general for requirements, verification and calibration of spring testing mach

DIN EN ISO 7500-1 Bb.3:1999 金属材料.静态单轴压缩试验机的验证.第1部分:拉伸/压缩试验机.测力系统的验证与校准.疲劳试验机的要求、验收和校准一般规则

Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines; verification and calibration of the force-measuring system; general for requirements, verification and calibration of fatigue testing mac

DIN EN ISO 7500-1 Bb.1:1999 金属材料.静态单轴向试验机的验证.第1部分:拉伸/压缩试验机.力测量系统的验证与校正.拉伸、压缩及弯曲试验机的要求、验证和校正的一般规则

Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines; verification and calibration of the force-measuring system; general for requirements, verification and calibration of tension, compressio

ISO 7500-1:1999 金属材料 静态单轴向试验机的验证 第1部分:拉伸/压缩试验机 力测量系统的验证和校正

Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines - Verification and calibration of the force-measuring system

JB/T 9398-1999 微小维氏硬度计 技术条件

Specifications for Vickers microhardness testers

JB/T 9377-1999 超声硬度计 技术条件

　　本标准规定了超声硬度计的技术要求、检验方法、检验规则、标志与包装等内容。 　　本标准适用于按超声接触阻抗法对金属材料进行布氏、洛氏和维氏硬度测定用的超声硬度计。

Specifications for ultrasonic hardness testers

JB/T 9376-1999 线材扭转试验机 技术条件

　　本标准规定了线材扭转试验机的技术要求、试验方法、检验规则、标志与包装等内容。 　　本标准适用于直径不大于10mm金属线材试验用的线材扭转试验机。

Specifications for the wire torsion testing machines

JB/T 9374-1999 纯弯曲疲劳试验机 技术条件

　　本标准规定了纯弯曲疲劳试验机的技术要求、检验方法、检验规则及标志、包装、运输与贮存。 　　本标准适用于金属试验用，试样旋转的纯弯曲疲劳试验机。亦适用于应用在特殊条件(如高温、腐蚀介质、环境气氛等)的试验机，但本标准对这些特殊条件不予规定。

Specifications for the rotary bending fatigue testing machines

JB/T 9373-1999 拉力蠕变试验机 技术条件

　　本标准规定了拉力蠕变试验机的技术要求、检验方法、检验规则、标志与包装等内容。 　　本标准适用于以电阻炉加热，最高试验温度为1200℃，并在空气中进行金属试验用的拉了蠕变试验机。

Specifications for the tensile - creep testing machines