N71 金属材料试验机 标准查询与下载

ASTM E821-96 带电粒子照射期间机械性能测量的标准规程

This practice covers the performance of mechanical tests on materials being irradiated with charged particles. These tests are designed to simulate or provide understanding of, or both, the mechanical behavior of materials during exposure to neutron irradiation. Practices are described that govern the test material, the particle beam, the experimental technique, and the damage calculations. Reference should be made to other ASTM standards, especially Practice E 521. Procedures are described that are applicable to creep and creep rupture tests made in tension and torsion test modes. The word simulation is used here in a broad sense to imply an approximation of the relevant neutron irradiation environment. The degree of conformity can range from poor to nearly exact. The intent is to produce a correspondence between one or more aspects of the neutron and charged particle irradiations such that fundamental relationships are established between irradiation or material parameters and the material response. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Measurement of Mechanical Properties During Charged-Particle Irradiation

ASTM E821-96(2009) 带电粒子照射期间机械性能测量的标准实施规程

1.1 This practice covers the performance of mechanical tests on materials being irradiated with charged particles. These tests are designed to simulate or provide understanding of, or both, the mechanical behavior of materials during exposure to neutron irradiation. Practices are described that govern the test material, the particle beam, the experimental technique, and the damage calculations. Reference should be made to other ASTM standards, especially Practice E 521. Procedures are described that are applicable to creep and creep rupture tests made in tension and torsion test modes. 1.2 The word simulation is used here in a broad sense to imply an approximation of the relevant neutron irradiation environment. The degree of conformity can range from poor to nearly exact. The intent is to produce a correspondence between one or more aspects of the neutron and charged particle irradiations such that fundamental relationships are established between irradiation or material parameters and the material response. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Measurement of Mechanical Properties During Charged-Particle Irradiation

JB/T 7796-1995 弹簧技压试验机 技术条件

Technical conditions of spring compression testing machine

JIS B 7724:1994 布氏硬度试验机

Brinell hardness testing machines

JIS B 7755:1993 金属材料用冲击试验机械.仪器

この規格は，JIS Z 2202による試験片及びこれに準じる試験片の衝撃試験に用いる計装化シヤルピー衛撃試験機()(以下，試験機という。)の計装化装置の性能について規定する。

Impact testing machines for metallic materials -- Instrumentation

JB/T 6865-1993 摆锤式高、低温冲击试验机 技术条件

本标准规定了摆锤式高、低温冲击试验机的技术要求、试验方法、检验规则、成套性、随机文件、标志及包装。 本标准适用于高温以电阻炉加热，低温以气体介质冷却，送试样机构采用直冲法，测定金属材料在200～1000℃或-192～0℃温度范围内的冲击吸收功，冲击能量为30～500J的摆锤式高、低温冲击试验机。

Pendulum type high and low temperature impact testing machine technical conditions

JB/T 6871-1993 液压式万能试验机可靠性试验方法

Reliability test method of hydraulic universal testing machine

JIS B 7727:1993 肖氏硬度试验机

Shore hardness testing machines

JB/T 5488-1991 高频疲劳试验机

本标准对高频疲劳试验机的主参数系列、技术要求、试验方法、检验规则、标志、包装、运输、贮存等做了统一的规定。 本标准适用于最大试验力不大于500kN、最大动态试验力不超过±250kN的金属材料及构件试验用的电磁共振型高频疲劳试验机。

High-frequency fatigue tester

JB/T 5487-1991 齿面洛氏硬度计 技术条件

本标准规定了齿面洛氏硬度计的技术要求、试验方法、检验规则、判定规则、成套性及标志、包装、随机文件等内容。 本标准适用于便携式的齿面洛氏硬度计

Specifications for tooth surface Rockwell hardness tester

JIS B 7741:1991 金属材料拉伸试验用伸长仪

Extensometers used in metallic material tensile testing

prEN 10002-4-1991 金属材料.第1部分:用于单轴向试验的变形测定仪的检验

Metallic materials; part 1: verification of extensometers used in uniaxial testing

STAS 12872-1990 氢化食用油

Prezentul standard se refer? la uleiul comestibil hidrogenat (plantol), ob?inut prin hidro-genarea uleiurilor comestibile rafinate din floarea soarelui sau soia, cu adaos de 10% ulei comestibil fluid, utilizat ?n industria alimentar?, cosmetic? si industr

Hydrogenated edible oil

JIS B 7722:1990 摆锤式冲击试验机

Charpy impact testing machines

ISO 1079:1989 金属材料.硬度试验.洛氏表面硬度试验机(15N、30N、45N、15T、30T和45T标尺)

This International Standard specifies a method of verification of testing machines for determining Rockwell superficial hardness (scales 15N, 30N, 45N, 15T, 30T and 45T) in accordance with It describes a direct verification method for checking the main functions of the machine, and an indirect verification method suitable for the overall checking of the machine. The indirect verification method may be used on its own for periodic routine checking of the machine in service. If a testing machine is also to be used for other methods of hardness testing, it shall be verified independently for each method.

Metallic materials; hardness test; verification of Rockwell superficial hardness testing machines (scales 15N, 30N, 45N, 15T, 30T and 45T)

ISO 376:1987 金属材料.用于验证单轴向试验机的作用力检验仪的校准

Metallic materials; Calibration of force-proving instruments used for the verification of unaxial testing machines

ISO 716:1986 金属材料.硬度试验.洛氏硬度试验机(A、B、C、D、E、F、G、H、K 标度)的校验

Metallic materials; Hardness test; Verification of Rockwell hardness testing machines (scales A - B - C - D - E - F - G - H - K)

ISO 7500-1:1986 金属材料.静态单轴向试验机的校正.第1部分:拉伸试验机

Metallic materials; Verification of static uniaxial testing machines; Part 1 : Tensile testing machines

DIN 51200:1985 材料试验机.硬度试验机的试样夹紧装置的设计和应用

This standard described the design and the application of holding devices for test pices in hardness testing machines.

Materials testing machines; design and application of test piece holding devices in hardness testing machines

NF A03-520:1985 钢铁. 机械式试验机检查用指南(张力.冲击.硬度).

Iron and steel - Guide for checking mechanical testing machines (tension - impact - hardness).

Iron and steel - Guide for checking mechanical testing machines (tension - impact - hardness).