P20 工程结构综合 标准查询与下载

JGJ 74-2003 建筑工程大模板技术规程

Technical specification for large-area formwork building construction

BS EN 12446:2003 烟囱.部部件.混凝土外壁构元件

This European Standard specifies the material, dimensional and performance requirements for factory made concrete outer wall elements for chimneys including fittings. The standard covers elements having up to four passages designated to accommodate a combination of flue liners and or air ducts. This European Standard also relates to storey-height and reinforced outer wall elements. NOTE 1 Classes in this standard are not derived from conditions referred to in article 3.2 of Directive 89/106/EC and should only be considered as technical classes in the sense of Commission Guidance Paper E "Levels and classes in the Construction Products Directive". NOTE 2 Any reference to the term 'outer wall element' implies both the outer wall elements and their fittings, except where otherwise indicated.

Chimneys - Components - Concrete outer wall elements

NF P06-100-1*NF EN 1990:2003 欧洲法规:结构设计基础

Eurocode - Basis of structural design.

DIN 1055-8:2003 对结构的作用.第8部分:在施工期间的作用

Actions on structures - Part 8: Actions during execution

ASTM E2265-03 混凝土和砖石工程用锚固件和紧固件的标准术语

1.1 This document provides standard terminology for anchors and fasteners installed in structural members made of concrete or masonry.1.2 This terminology does not cover terms relating to the mechanical properties of the materials used for fabricating anchors, nor does it cover their use.1.3 The terms are listed alphabetically. Compound terms appear in the natural spoken order.

Standard Terminology for Anchors and Fasteners in Concrete and Masonry

ASTM E695-03(2009) 墙、楼板和屋顶建筑的相对抗冲击负荷测量的标准方法

The procedures outlined will provide data that can be used to evaluate the relative performance of wall, floor, and roof constructions under conditions representative of those sustained in actual service when subjected to impact by a heavy blunt object. See Test Method E 661 for evaluation of floor and roof sheathing and Practice E 73 for evaluation of roof trusses. The method is intended to be applied to relatively light construction, including, but not limited to, wood floor and roof systems, partitions framed with wood or steel studs, steel floor or roof decking systems, steel siding and wall panels, or thin concrete and masonry walls or slabs and similar assemblies.1.1 This test method covers the measurement of the relative resistance of wall, floor, and roof construction to impact loading. The test is not applicable to doors. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Method for Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading

ASTM E695-03 墙、楼板和屋顶建筑的相对抗冲击负荷测量的标准方法

The procedures outlined will provide data that can be used to evaluate the relative performance of wall, floor, and roof constructions under conditions representative of those sustained in actual service when subjected to impact by a heavy blunt object. See Test Method E 661 for evaluation of floor and roof sheathing and Practice E 73 for evaluation of roof trusses. The method is intended to be applied to relatively light construction, including, but not limited to, wood floor and roof systems, partitions framed with wood or steel studs, steel floor or roof decking systems, steel siding and wall panels, or thin concrete and masonry walls or slabs and similar assemblies.1.1 This method covers the measurement of the relative resistance of wall, floor, and roof construction to impact loading. The test is not applicable to doors. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Method for Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading

KS F ISO 2394:2002 结构可靠性的通用原则

이 규격은 이미 알고 있거나 예상되는 작용에 대한 구조물의 신뢰도를 확인하기 위한 일반

General principles on reliability for structures

BS EN 60335-2-83:2002 家用和类似用途电器的安全性.特殊要求. 屋顶排水用加热集水槽沟

To be read in conjunction with BS EN 60335-1:2002

Specification for safety of household and similar electrical appliances - Particular requirements - Heated gullies for roof drainage

BS EN 13101:2002 地下室人入口处的阶梯.要求、标志、试验和舒适度的评定

This standard specifies general requirements and testing methods for steps manufactured from cast iron, steel or aluminium, for use in manholes and other underground man entry chambers as a means of access. This standard specifies performance criteria for mechanical stability and resistance providing protection against falling. Corresponding test methods and evaluation of conformity are included. The steps specified in this European Standard are suitable for use in sewage, surface water and, subject to the requirements of national regulations, potable water environments. Where steps are to be used in particular corrosive environments, e.g. industrial effluents, additional protection may be required. This standard does not apply for steps moulded in prefabricated manholes of the same material.

Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity

DIN 1055-7:2002 对建筑物的作用.第7部分:热作用

The standard is part of a new series of standards for actions on structures which are developed on the basis of related European Standards and which are suposed to replace or complete the existing series DIN 1055. This standard is in particular derived from DIN V ENV 1991-2-5, which are exposed to dayly and seasonal diveations of temperature. As far as possible thermal actions for the design of structures are given in terms of characteristic values. With the exception for chimneys and pipes thermal actions which are caused by the use of the structure are not dealt with.#,,#

Actions on structures - Part 7: Thermal actions

BS EN 13502:2002 烟囱.泥土/陶瓷烟道口的要求和试验方法

This European Standard specifies requirements and test methods for clay/ceramic flue terminals with solid walls, which serve to convey the products of combustion from the flue to the atmosphere by negative pressure. It includes terminals used on domestic and industrial chimneys which are not structurally independent (free standing). This standard specifies the performance requirements for factory made terminals. Marking and inspection are also covered by this standard.

Chimneys - Requirements and test methods for clay/ceramic flue terminals

KS F ISO 4354:2002 结构物的防风作用

이 규격은 구조물에 대한 바람의 작용을 서술하며, 건축물, 타워, 굴뚝, 교량 그리고 기타

Wind actions on structures

KS F ISO 9194:2002 结构设计基础.结构自重、非结构构件自重和储存材料自重的作用.密度

이 규격은 구조물, 비구조 요소, 저장물의 자중에 의한 작용을 규정하며 그리고 그들의 밀도

Bases for design of structures-Actions due to the self-weight of structures,non-structural elements and stored materials-Density

KS F ISO 4356:2002 结构设计基础.耐用性极限状态下的建筑物变形

이 규격은 사용성 한계 상태에서 건축물의 변형에 대한 기준, 규정, 권장 사항 등을 제정할

Bases for the design of structures-Deformations of buildings at the serviceability limit states

DIN 1055-3:2002 对结构的作用.第3部分:建筑物的自重和施加载荷

Action on structures - Part 3: Self-weight and imposed load in building

DIN EN 12152:2002 幕墙.透气率.性能要求和分类

Curtain walling - Air permeability - Performance requirements and classification; German version EN 12152:2002

BS EN 1990:2002+A1:2005 欧洲规范.结构设计基础

(1) EN 1990 establishes Principles and requirements for the safety, serviceability and durability of structures, describes the basis for their design and verification and gives guidelines for related aspects of structural reliability. (2) EN 1990 is intended to be used in conjunction with EN 1991 to EN 1999 for the structural design of buildings and civil engineering works, including geotechnical aspects, structural fire design, situations involving earthquakes, execution and temporary structures. NOTE For the design of special construction works (e.g. nuclear installations, dams, etc.), other provisions than those in EN 1990 to EN 1999 might be necessary. (3) EN 1990 is applicable for the design of structures where other materials or other actions outside the scope of EN 1991 to EN 1999 are involved. (4) EN 1990 is applicable for the structural appraisal of existing construction, in developing the design of repairs and alterations or in assessing changes of use.

Eurocode - Basis of structural design

BS EN 1990:2002 欧洲法规.结构设计基础.BS EN 1990-2002和国家附录的编辑

(1) EN 1990 establishes Principles and requirements for the safety, serviceability and durability of structures, describes the basis for their design and verification and gives guidelines for related aspects of structural reliability. (2) EN 1990 is intended to be used in conjunction with EN 1991 to EN 1999 for the structural design of buildings and civil engineering works, including geotechnical as-pects, structural fire design, situations involving earthquakes, execution and temporary structures. NOTE For the design of special construction works (e.g. nuclear installations, dams, etc.), other provi-sions than those in EN 1990 to EN 1999 might be necessary. (3) EN 1990 is applicable for the design of structures where other materials or other actions outside the scope of EN 1991 to EN 1999 are involved. (4) EN 1990 is applicable for the structural appraisal of existing construction, in devel-oping the design of repairs and alterations or in assessing changes of use. NOTE Additional or amended provisions might be necessary where appropriate.

Eurocode - Basis of structural design

KS F ISO 3898:2002 结构设计基础.符号表示法.常用符号

이 규격은 구조 설계에 사용되는 표준 표기들에 대하여 규정한다.이 규격은 구조 설계 분

Bases for design of structures－Notations－General symbols