P26 金属结构工程 标准查询与下载
共找到 501 条与 金属结构工程 相关的标准，共 34 页
本标准规定了电子经纬仪/全站仪三维坐标测量技术用于水工金属结构检测的基本要求和方法。 本标准适用于闸门、启闭机、压力钢管、拦污栅、清污机、升船机等水工金属结构产品的检测，水利水电工程其他产品检测可参照执行。
Directives for three-dimensional coordinate measurement of hydro steel structure
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-10-19
- 实施
- 2013-01-19
本标准规定了磁弹法测试残余应力的基本原理和测试方法。本标准适用于水工金属结构以及其他铁磁性材料的焊接件、铸锻件、热处理件近表面残余应力的测定。
Residual stress analysis for hydraulic steel structure by magnetoelastic method
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-09-10
- 实施
- 2012-12-10
本规程主要适用于钢结构房屋建筑，钢-混凝土组合结构、钢-木组合结构中外露钢构件以及钢结构构筑物等也可适用本规程。 钢结构建筑的维护、修理，如涉及主体结构的改变、结构的用途和使用环境的改变，应由法定检测单位进行技术鉴定，并经原设计单位或具有相应资质的设计单位进行变更设计或认可。
Technical specification for steel structure building maintenance
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-08-09
- 实施
- 2012-09-09
本标准规定了水工金属结构产品的钢融化焊T形接头角焊缝/对接和角接组合焊缝（以下简称组合焊缝）采用A型脉冲反射式超声波探伤仪检测缺陷的超声检测方法和质量分级要求。 本标准适用于水利水电工程闸门、拦污栅、清污机、压力钢管、启闭机、吊杆、自动挂脱梁等水工金属结构产品母材厚度为8～120mm铁素体钢融化焊T形接头角焊缝/组合焊缝超声检测及其质量评定。 水利水电工程中的其他产品或工件的钢融化焊T形接头、十字接头角焊缝/组合焊缝的超声检测，在役水工金属结构产品检验，可参照本标准执行。
Ultrasonic testing method and quality classification for T-joint fillet welds and combination of butter weld and fillet weld of hydro steel structures
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-08-06
- 实施
- 2012-11-06
This National Annex contains national provisions relating to the design of steel bridges and steel members in composite bridges as well as further specifications complementing,amending or replacing specifications in the various parts of EN 1993-1 that are to be taken into consideration when applying DIN EN 1993-2:2010-12 in Germany. This National Annex is only valid in conjunction with DIN EN 1993-2:2010-12.
National Annex.Nationally determined parameters.Eurocode 3: Design of steel structures.Part 2: Steel bridges
- ICS
- 91.010.30;91.080.10;93.040
- CCS
- P26
- 发布
- 2012-08
- 实施
本标准规定了水工金属结构制造与安装检验的一般要求、检验项目与检验方法。本标准适用于水利水电工程闸门、拦污栅、压力钢管、启闭机和清污机等水工金属结构设备的制造与安装检验。
Directives for quality inspection of manufacture and installation of hydro steel structure
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-07-20
- 实施
- 2012-10-20
Technical specification for selection and inspection of steel materials for steel structures
- ICS
- CCS
- P26
- 发布
- 2012-06-01
- 实施
- 2012-06-01
This part of ISO 630 specifies qualities for high-yield-strength quenched and tempered structural steels. This part of ISO 630 applies to steel plates rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site. This part of ISO 630 covers 10 grades. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B.
Structural steels - Part 4: Technical delivery conditions for high-yield-strength quenched and tempered structural steel plates
- ICS
- 77.140.01
- CCS
- P26
- 发布
- 2012-06
- 实施
This part of ISO 630 specifies requirements for flat and long products of hot-rolled weldable fine-grain structural steels in the as-rolled (for SG grades only), normalized/normalized-rolled and thermomechanical-rolled delivery conditions. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are intended for use in heavily loaded parts of welded or bolted structures. This part of ISO 630 covers 11 grades and four qualities. Grades S275, S355, S420 and S460 are covered in Annex A. Grades SG245, SG290, SG325, SG345, SG365, SG415 and SG460 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site.
Structural steels - Part 3: Technical delivery conditions for fine-grain structural steels
- ICS
- 77.140.01
- CCS
- P26
- 发布
- 2012-06
- 实施
本标准规定了冷轧高强度建筑结构用薄钢板（以下简称高强钢板）的术语和定义、分类和标记、一般要求、要求、试验方法、检验规则、订货内容、标志、包装及质量证明书、使用环境的描述、国内外牌号近似对照。 本标准适用于工业与民用建筑结构用规定最小屈服强度不小于450MPa,公称厚度为0.30mm～3.00mm的高强度热镀锌钢板、热镀铝锌钢板、彩涂热镀锌钢板和彩涂热镀铝锌钢板。
High-strength cold-rolled steel sheet for building structure
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-04-01
- 实施
- 2012-10-01
本标准规定了钢筋桁架楼承板的术语和定义、标记与示例、材料、要求、试验方法、检验规则、订货内容、标志、包装、运输和贮存。 本标准适用于工业与民用建筑及构筑物组合楼盖所用的钢筋桁架楼承板的生产、检验和验收。
Steel-bars truss deck
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-02-09
- 实施
- 2012-08-01
本标准规定了缓粘结预应力钢绞线专用粘合剂（简称缓凝粘合剂，代号为Ra）的术语和定义、标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于缓粘结预应力钢绞线专用粘合剂的生产和检验。
Adhesive for retard-bonded prestressing steel strand
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-02-09
- 实施
- 2012-08-01
Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; German version EN 1090-1:2009+A1:2011
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012-02-01
- 实施
Entertainment Technology - Design, Manufacture and Use of Aluminum Trusses and Towers
- ICS
- 97.200.10
- CCS
- P26
- 发布
- 2012
- 实施
Supplement 1 to the North American Standard for Cold-Formed Steel Framing - Wall Stud Design
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012
- 实施
North American Standard for Cold-Formed Steel Framing - Truss Design
- ICS
- 77.140.01
- CCS
- P26
- 发布
- 2012
- 实施
North American Specification for the Design of Cold-Formed Steel Structural Members
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012
- 实施
North American Standard for Cold-Formed Steel Framing - General Provisions
- ICS
- 91.080.10
- CCS
- P26
- 发布
- 2012
- 实施
Supplement 3 to Standard for Cold-Formed Steel Framing - Prescriptive Method for One and Two Family Dwellings, 2007 Edition
- ICS
- 91.040.30;91.080.10
- CCS
- P26
- 发布
- 2012
- 实施
本标准规定了废物箱的术语和定义、分类、型号编制、要求、试验方法、检验规则、标志、包装和运输、贮存等。 本标准适用于废物箱的生产、使用和检验。
General technical specifications for waste bin
- ICS
- 13.030.50
- CCS
- P26
- 发布
- 2011-11-25
- 实施
- 2012-05-01
