P62 输、变电工程 标准查询与下载

NRS 093-1-2009 电力基础设施的资产管理．第1部分：南非配电行业中资产管理的最低要求

Sets out minimum requirements for asset management of electricity infrastructure at an electricity utility.

Asset management of electricity infrastructure Part 1: Minimum requirements for asset management in the South African Electricity Distribution Industry

NRS 089-5-1-2009 电网维护．第5部分:街道照明和高电线杆．第1节:街道照明和电线杆的维护

Provides minimum maintenance requirements for street lighting equipment and high masts as required by NRS 082-0 and the NRS 089 series.

Maintenance of electricity networks Part 5: Street lighting and high masts Section 1: Maintenance of street lighting and high masts

JIS C 3653 ERRATUM 1:2008 勘误表

ERRATUM

SANS 10280-1:2008 南非常见条件下的架空电力线路.第1部分:安全

Specifies mechanical and electrical safety requirements of overhead power lines including requirements for supports, the conductor system, clearances and crossings.

Overhead power lines for conditions prevailing in South Africa Part 1: Safety

ANSI/IEEE 691:2007 传输结构的基础设计和测试用指南

The design of foundations for conventional transmission line structures, which include lattice towers, single or multiple shaft poles, H-frame structures, and anchors for guyed structures is presented in this guide.

Guide for Transmission Structure Foundation Design and Testing

IEEE 605-2008 空气绝缘技变电站中的母线设计指南

Guide for Bus Design in Air Insulated Substations

DL/T 5056-2007 变电站总布置设计技术规程

本标准规定了变电站总布置设计的基本技术要求。 本标准适用于电压等级为110kV~750kV新建或扩建变电站的总布置设计。对750kV以上电压等级的变电站、改建的变电站以及换流站的总布置设计可参照使用。

Technical code of general plan design for substation

ANSI/IEEE 525:2007 变电站电缆系统的设计和安装

The document is a guide for the design, installation, and protection of insulated wire and cable systems in substations with the objective of minimizing cable failures and their consequences.

Design and Installation of Cable Systems in Substations

ANSI/IEEE 1615:2007 变电所网络通信的推荐实施规程

Explains recommended practices for communication and interoperation of devices connected on an electric power substation internet protocol (IP) network. For the power engineer new to IP networking, it provides an introduction to the concepts that need to be mastered as well as specific recommendations to follow when deploying the techniques. For equipment manufacturers and system integrators, it provides direction and requirements to facilitate interoperable electric utility information networks.

Recommended Practice for Network Communication in Electric Power Substations

DL/T 860.5-2006 变电站通信网络和系统 第5部分:功能的通信要求和装置模型

DL/T 860系列标准本部分适用于变电站自动化系统，规定了智能电子设备之间的通信和相关系统的要求。 本部分规定了变电站自动化系统所完成功能的通信要求和装置模型，辨别所有己知的功能和通信要求。 功能的描述并不是用于功能标准化，而是用于辨别技术服务和变电站之间、变电站内智能电子设备之间的通信要求。基本目标是所有相互作用中互操作。 对功能和实现标准化，完全超出本标准的范围。因而，在DL/T 860系列标准中认为将功能分配到装置可有多种分配策略。为支持功能自由分配提出的要求，规定了将功能适当分解为相关通信部分，规定了交换数据和所要求的性能。对典型变电站配置，通过信息数据流计算补充前述规定。 变电站智能电子设备，譬如保护装置也可能在像电厂这样的场所中使用。对于在这些场所使用的装置，使用本标准可方便系统集成，但这己超出本标准的范围。

Communication networks and systems in substations Part 5: Communication requirements for functions and device models

DL/T 5342-2006 750 kV架空送电线路铁塔组立施工工艺导则

本标准规定了750kV架空送电线路铁塔组立施工工艺。 本标准适用于新建、改（扩）建750kV送电线路一般铁塔（全高100m以下）的组立工程。500kV及以下线路的铁塔组立可参考执行。

Construction technology guidance for the assembling and erection of the steel towers of 750KV overhead transmission line

DL/T 5343-2006 750 kV架空送电线路张力架线施工工艺导则

本标准规定了架空送电线路中导线、架空地线、光纤复合架空地线（OPGW）的张力架线施工工艺。 本标准适用于750kV架空送电线路。 以下特殊张力架线施工可参照本标准，进行编制特殊张力架线施工方案： 1 大跨越张力架线施工。 2 不停电跨越张力架线施工。 3 采用过渡方法的张力架线施工。 4 采用环形牵放方式的张力架线施工。 5 多于六分裂导线的线路张力架线施工。

ConstnEdom technology guidance for tension stdnghg of 750kV overhead transmission line

DL/T 5033-2006 输电线路对电信线路危险和干扰影响防护设计规程

本标准规定了交流高压架空输电线路（简称输电线路）对电信线路危险和干扰影响允许值，给出了危险和干扰影响计算方法，提供了必要的参数、提出了防护措施。 本标准适用于35kV及以上三组交流架空输电线路对符合相关标准要求的电信线路的防护设计。

The design rules of telecommunication lines against danger and interference effects from power transmission lines

DL/T 5049-2006 架空送电线路大跨越工程勘测技术规程

本标准规定了架空送电线路大跨越工程的工程测量、岩土工程勘测、工程水文勘测的基本技术要求。 本标准适用于220kV～750kV架空送电线路大跨越工程的工程勘测。其他电压等级的架空送电线路大跨越工程的工程勘测可参照执行。 架空送电线路跨越通航大河流、湖泊或海峡等，因档距较大（一般在1000m以上）或塔的高度较高（一般在100m以上），导线选型或塔的设计需予以特殊考虑，且发生故障时严重影响航运或修复特别困难的耐张段，应该按大跨越工程进行勘测。

Technical code exploration and surveying of largr crossing overhead transmission line

NRS 043-2005 电力和电信线路用构筑物的同杆架设

Applies in cases where power lines, of nominal phase-to-phase voltage up to and including 33 kV, share a route with telecommunication lines where telecommuinication lines are to be added to existing power line structures, where power lines are to be adde

Joint use of structures for power and telecommunication lines

DL/T 968-2005 高压直流输电工程启动及竣工验收规程

本标准规定了高压直流输电工程启动及竣工验收各阶段有关单位的职责和主要工作内容。 本标准适用于电力行业高压直流输电工程和背靠背换流站的启动及竣工验收，特高压直流工程启动及竣工验收可以参照执行。

Code of start-up & completion acceptance for HVDC transmission project

PIESA 1018-3-2004 使用架空导线束的低压架空电力线路用配件和连接器．第3部分：裸露中性线制成导线用拉紧和悬吊配件

PIESA 1018-3 covers the requirements for the manufacture, testing and supply of strain and suspension fittings for bare neutral supporting conductors for use on a.c. system voltage up to and including 1 000 V, and is based on European standards that have

Fittings and connectors for low-voltage overhead power lines using aerial bundled conductors Part 3: Strain and suspension fittings for bare neutral support conductors

PIESA 1018-2-2004 使用架空导线束的低压架空电力线路．第2部分：绝缘中性线支撑导线用拉紧和悬吊配件

PIESA 1018-2 covers the requirements for the manufacture, testing and supply of strain and suspension fittings for insulated neutral supporting conductors for use on a.c. system voltages up to and including 1 000 V, and is based on European standards whi

Fittings and connectors for low-voltage overhead power lines using aerial bundled conductors Part 2: Strain and suspension fittings for insulated neutral supporting conductors

PIESA 1018-4-2004 使用架空导线束的低压架空电力线路用配件和连接器．第4部分：架空用户电缆用拉紧和吊线配件

Covers the requirements for the manufacture, testing and supply of strain and suspension fittings for aerial service cables for use on a.c. system voltages up to and including 1000 V, and is based on European standards that have been modified where neces

Fittings and connectors for low voltage overhead power lines using aerial bundled conductors Part 4: Strain and suspension fittings for aerial service cables

PIESA 1018-5-2004 使用架空导线束的低压架空电力线路的配件和连接器．第5部分：带电连接器和接头

Covers the requirements for the manufacture, testing and supply of current-carrying connectors and joints for aerial bundled conductors for use on a.c. system voltages up to and including 1 000 V.

Fittings and connectors for low voltage overhead power lines using aerial bundled conductors Part 5: Current-carrying connectors and joints