P92 电信设备安装工程 标准查询与下载

DB31/T 370.4-2006 宽带接入工程系列标准 第4部分：基于HFC的有线电视宽带接入网工程验收规范

Broadband Access Engineering Series Standards Part 4: HFC-based CATV Broadband Access Network Engineering Acceptance Specifications

DB31/T 370.1-2006 宽带接入工程系列标准 第1部分：基于FTTB+LAN方式的接入工程设计规范

本标准适用于采用FTTB+LAN网络布线方案进行宽带网络建设的新建住宅、需要进行FTTB+LAN改造的已建住宅的工程设计。功能和用途明确的公共建筑及办公楼可参照此标准执行。

Broadband Access Engineering Series Standards Part 1: Access Engineering Design Specifications Based on FTTB+LAN

DB31/T 370.2-2006 宽带接入工程系列标准 第2部分：无线局域网工程施工及验收测试规范

本标准无线局域网工程的施工、测试、验收要求。本标准适用于基于GB 15629.1102的无线局域网，基于GB 15629.1101、15629.1104的无线局域网的施工和测试验收工作也可参照此标准执行。

Broadband Access Engineering Series Standards Part 2: Wireless Local Area Network Engineering Construction and Acceptance Test Specifications

DIN CEN/TS 15231:2006 建筑自动化、控制和建筑管理中开放式数据通信.LONWORKS和BAC网之间的地图

Open data communication in building automation, controls and building management - Mapping between LONWORKS and BACnet; English version CEN/TS 15231:2006

YD 5125-2005 通信设备安装工程施工监理暂行规定

本暂行规定适用于新建光缆传输系统设备、电话交换设备、微波接力系统设备安装工程施工监理。扩建、改建工程可参照本暂行规定执行。

Provisional Specification Speeification of Installation Engineering for Communication Equipment

YD 5059-2005 电信设备安装抗震设计规范

本规范适用于抗震设防烈度为6～9度地区的新建电信设备安装工程及安装在屋顶上或屋顶塔上的微波天馈线、移动天馈线的抗震设计。改建、扩建电信设备安装工程参照执行。

Design Specification for Seismic Installation of Telecommunication Equipment

YD/T 5035-2005 数字集群通信设备安装工程验收暂行规定

本规定适用于800MHz集群通信工程的施工验收（含数字集群通信体制（A）、数字集群通信体制（B）和基于GSM、CDMA技术的数字集群通信系统），150MHz、450MHz频段小容量集群通信系统的验收可参照执行。

Temporary Specifications of Engineering Acceptance for Digital Trunked Communication Equipments Installation

YD/T 5141-2005 SDH数字微波设备安装工程验收规范

本规范是新建SDH数字微波设备安装工程中进行施工质量检查、阶段验收以及竣工验收等工作的依据。对于改、扩建工程参照执行。

Accetping Specification of Equipment Installation Engineering for SDH Digital Microwave

BS EN 50310:2006 带有信息技术设备的建筑物中等势连接和接地的应用

This European Standard applies to the equipotential bonding inside buildings in which information technology equipment is going to be installed. It contributes to the standardisation of information technology equipment and co-ordinates with the pre-requirements of the generic installation conditions as outlined in IEC 60364-5-548 to achieve the following targets: a) safety from electrical hazards; b) reliable signal reference within the entire information technology installation; c) satisfactory electromagnetic performance of the entire information technology installation. A defined bonding configuration down to the equipment level independent of the equipment supplier is intended to facilitate the installation, operation and maintenance of information technology installations in buildings; the interworking between different information technology equipment (interconnected by metallic links). The specification of information technology equipment and of the pre-requirements of installation are subject to agreement of the parties (e. g. the equipment supplier and the purchaser or building owner). This standard applies to buildings with information technology equpiment or in which the installation of information technology equipment is intended. It provides additional information for architects of buildings and for designers and installers of electrical installations of buildings on some installation concepts that limit electromagnetic influences. Basic considerations are given here to mitigate such influences that may result in disturbance. This standard does not apply to buildings which may be subject to a harsh electromagnetic environment, or rooms containing the generation, transmission or termination of voltages over AC 1000 V. This standard does not address the specific requirements for telecommunication centres; these are specified in EN 300253.

Application of equipotential bonding and earthing in buildings with information technology equipment

KS C 3617-2006 电视机同轴电缆

이 규격은 위성 방송을 포함한 텔레비전 수신용 기기 및 관련 기기의 접속에 사용하는 텔레비

Coaxial cables for television receivers

YD/T 5139-2005 有线接入网设备安装工程设计规范

本规范适用于本地通信网中有线接入网设备的新建工程。对于改扩建工程和有线接入网工程可参照执行。

Design Specification for Equipment Installation of Cable Access Network

YD/T 5140-2005 有线接入网设备安装工程验收规范

本规范适用于有线接入网新建工程的设备安装工程随工检查、初验、试运行和终验（竣工验收）。扩建、改建工程可参照执行。

Acceptance Specifications for Equipment Installation Project of wired Access Network

SANS 10340-1:2006 通信电缆的安装．第1部分：建筑物内的光缆

Addresses installation requirements, primarily for indoor cabling, but also for campus-wide inter-building cabling, for high performance fibre optic cable that serves to transmit voice, video and data telecommunication.

Installation of telecommunication cables Part 1: Fibre optic cable in buildings

ANSI/DASMA 303-2006 便于残疾人使用的通信入口系统的性能标准

Defines general requirement and performance-based criteria for evaluating accessible communications entry systems. This standard is intended to cover accessible communications entry systems generally used for public pedestrian access to controlled entry buildings for intercom or assistance purposes. This standard is not intended to cover communications entry systems generally used for emergency access.

Performance Criteria for Accessible Communications Entry Systems

DIN EN 14908-2:2006 建筑自动化、控制和建筑管理的开放式数据通信.控制网络协议.第2部分:双扭线通信

This European standard specifies the control network protocol (CNP) free-topology twisted-pair channel and serves as a companion document to CNP, part 1. The channel supports communication at 78.125 kbps between multiple nodes, each of which consists of a transceiver, a protocol processor, an application processor, a power supply, and application electronics. This standard covers the complete physical layer (OSI Layer 1), including the interface to the Media Access Control (MAC) sub-layer and the interface to the medium. Parameters that are controlled by other layers but control the operation of the physical layer are also specified.#,,#

Open Data Communication in Building Automation, Controls and Building Management - Control Network Protocol - Part 2: Twisted Pair Communication; English version EN 14908-2:2005

DIN EN ISO 16484-3:2005 建筑自动化和控制系统(BACS).第3部分:功能

This Part 3 of the standard specifies the requirements for the overall functionality and engineering services to achieve building automation and control systems. It defines terms, which shall be used for specifications and it gives guidelines for the functional documentation of project/application specific systems. It provides a sample template for documentation of plant/application specific functions, called BACS points list in annex A. The informative function block examples explain a method to display the referenced functions in system documentation; they do not standardize the method for programming functions and applications. This part of the standard covers the following: Requirements and definitions regarding BACS and application software, generic functions for plant/project specific applications and engineering functions for building controls and operations. It provides communication functions for the integration of other dedicated special system processes. The functional requirements in this part of the standard are subdivided as follows: ~t-- System management and application software: describes the requirements for plant independent systems and human system interface programs related to a project, including the operating system. This standard does not dedicate the following system functionality to any particular hardware, e.g.: -- system diagnostics, watchdog, redundancy, time keeping, access control, log lists; -- point identification, event message handling, print control; -- database, statistics, data archiving, remote access; -- system communications. -- Human system interface (HSI), point information presentation, graphics, alarms, time scheduling. -- Engineering process and tool software: describes the requirements for configuring of the hardware and control strategies, the system management and the commissioning process. ~-- BACS application processing programs and plant/application specific functions: describes the requirements for plant, application and/or project specific functions and a method for the documentation of a project. The functions are subdivided into the following types: -- input and output functions, physical and shared; -- processing functions (e.g. for monitoring, interlocks, control and optimization); -- management functions (system programs), and required communications; -- operator functions. This Part 3 defines a method for specifying the procurement specifications containing all essential elements required for the operational functioning of a BACS. The successful installation and operation of a BACS requires that its procurement be based on a complete and accurate functional specification. The standard provides a template called the 'BACS points list' that can be found in annex A (normative). Its purpose is to determine and document the options for plant/application specific functionality based on the plant/control schematic. Further explanations can be given in form of plant/control descriptions and control flow chart diagrams. Examples are given in annex B (informative). The exact specifications will be project-specific. Information about the standardized functions is given in the form of informative examples as function-blocks, textual, and graphical descriptions in 5.5. It is recognized, that functions can be described and implemented in many different ways, depending on: -- climatic differences: -- cultural and regional differences; -- national regulations.

Building automation and control systems (BACS) - Part 3: Functions (ISO 16484-3:2005); English version of DIN EN ISO 16484-3:2005

ISO 16484-6:2005 建筑自动化和控制系统(BACS).第6部分:数据通信一致性试验

This part of ISO 16484 defines a standard method for verifying that an implementation of the BACnet protocol provides each capability claimed in its Protocol Implementation Conformance Statement (PICS) in conformance with the BACnet standard (ISO 16484-5). The scope is further detailed in Clause 2 of the enclosed ANSI/ASHRAE publication.

Building automation and control systems (BACS) - Part 6: Data communication conformance testing

YD/T 5032-2005 会议电视系统工程设计规范

本规范适用于基于ITU-T H.320标准和设置专用会议室的会议电视系统的新建工程。改、扩建工程可参照执行。专用会议电视用户进入会议电视网时，应遵守本设计规范的各项规定。

Code for Design of Videoconference System Engineering

YD/T 5033-2005 会议电视系统工程验收规范

本规范是会议电视系统安装工程中进行施工质量检查、阶段验收以及竣工验收等工作的技术依据。

Acceptance Specifications of Videoconference System Engineering

YD/T 5136-2005 IP视讯会议系统工程验收暂行规定

本规定是IP视讯会议系统设备安装工程随工检验、初步验收和竣工验收的技术依据。适用于新建的IP视讯会议电视系统建设工程，扩建和改建工程可参照执行。

Interim Provisions of Acceptance for IP Videoconference System Engineering