Q10 建材产品综合 标准查询与下载

ASTM E2277-03 煤灰建筑填充件的设计和制造的标准指南

1.1 This guide covers procedures for the design and construction of engineered structural fills using coal fly ash, bottom ash, or ponded ash.1.2 The utilization of coal ash under this guide is a component of a pollution prevention program; Guide E 1609 describes pollution prevention activities in more detail. Utilization of coal ash in this manner conserves land, natural resources, and energy.1.3 This guide applies only to fly ash and bottom ash produced primarily by the combustion of coal.1.4 The testing, engineering, and construction practices for coal ash fills are similar to generally accepted practices for natural soil fills. Coal ash structural fills should be designed using generally accepted engineering practices.1.5 Laws and regulations governing the use of coal ash vary by state. The user of this guide has the responsibility to determine and comply with applicable requirements.1.6 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Design and Construction of Coal Ash Structural Fills

ANSI/NFPA 259-2003 建筑材料潜在热的标准试验方法

This method of test shall provide a means of determining, under controlled laboratory conditions, the potential heat of building materials subjected to a defined high-temperature exposure condition.

Standard Test Method for Potential Heat of Building Materials

ASTM C4-03 粘土和多孔粘土排水管的标准规范

1.1 This specification establishes the criteria for acceptance, prior to installation, of drain tile and perforated drain tile to be used for underdrainage, filter fields, leaching fields, and similar subdrainage installations.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the Test Methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Note 18212;Attention is called to Test Methods C 301 and Terminology C 896.

Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile

ASTM D3161-03a 沥青瓦抗风的标准试验方法

1.1 This test method covers the procedure for testing asphalt shingles that are resistant to wind blow-up or blow-off when applied on low slopes in accordance with the manufacturer''s instructions. It is generally used to determine the blow-off resistance of sealed and interlocked shingles at a given wind velocity, but may be used to test unsealed or sealed shingles at other wind velocities as is applicable.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

ASTM D3161-03b 沥青瓦抗风的标准试验方法

1.1 This test method covers the procedure for testing asphalt shingles that are resistant to wind blow-up or blow-off when applied on low slopes in accordance with the manufacturer''s instructions. It is generally used to determine the blow-off resistance of sealed and interlocked shingles at a given wind velocity, but may be used to test unsealed or sealed shingles at other wind velocities as is applicable.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

ASTM D3161-03 沥青瓦抗风的标准试验方法

1.1 This test method covers the procedure for testing asphalt shingles that are resistant to wind blow-up or blow-off when applied on low slopes in accordance with the manufacturer''s instructions. It is generally used to determine the blow-off resistance of sealed and interlocked shingles at a given wind velocity, but may be used to test unsealed or sealed shingles at other wind velocities as is applicable.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

ASTM E84-03b 建筑材料表面燃烧特性的标准试验方法

1.1 This fire-test-response standard for the comparative surface burning behavior of building materials is applicable to exposed surfaces such as walls and ceilings. The test is conducted with the specimen in the ceiling position with the surface to be evaluated exposed face down to the ignition source. The material, product, or assembly shall be capable of being mounted in the test position during the test. Thus, the specimen shall either be self-supporting by its own structural quality, held in place by added supports along the test surface, or secured from the back side.1.2 The purpose of this test method is to determine the relative burning behavior of the material by observing the flame spread along the specimen. Flame spread and smoke developed index are reported. However, there is not necessarily a relationship between these two measurements.1.3 The use of supporting materials on the underside of the test specimen has the ability to lower the flame spread index from those which might be obtained if the specimen could be tested without such support. These test results do not necessarily relate to indices obtained by testing materials without such support.1.4 Testing of materials that melt, drip, or delaminate to such a degree that the continuity of the flame front is destroyed, results in low flame spread indices that do not relate directly to indices obtained by testing materials that remain in place.1.5 The values stated in inch-pound units are to be regarded as the standard.1.6 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Surface Burning Characteristics of Building Materials

BS EN 12271-3:2002 表面修琢.规范.粘合剂和石屑摊铺的速度和准确度

This European Standard specifies the classes of limit deviations for the rate of spread of binder and chippings to be applied to the design of a surface dressing and sets limits for coefficients of variation for the accuracy of transverse distribution of binder and chippings. This European Standard is applicable to surface dressings for roads, airfields and other trafficked areas.

Surface dressing - Specifications - Rate of spread and accuracy of spread of binder and chippings

BS EN 12272-1:2002 敷路料.试验方法.粘合剂和石屑摊铺的速度和准确度

This European Standard specifies test methods for determining the rates of spread and accuracy of spread of binder and chippings of a surface dressing on a section of road at a given time. It is also applicable to surface dressings on airfields and other trafficked areas. The test methods are used on site to check the ability of binder sprayers and chipping spreaders to meet the intended rates of spread and tolerances and coefficients of variation. The test methods for measuring the rates of spread and accuracy of spread of binders and chippings are not applicable to combined chipping-binder spreaders.

Surface dressing - Test methods - Rate of spread and accuracy of spread of binder and chippings

ISO 1182:2002 建筑材料的对火反应试验.不可燃性试验

This European Standard specifies a method of test for determining the non-combustibility performance, under specified conditions, of homogeneous building products and substantial components of non-homogeneous building products. Information on the precision of the test method is given in annex A.

Reaction to fire tests for building products - Non-combustibility test

ISO 1716:2002 建筑产品耐火反应试验.燃烧热的测定

This European Standard specifies a method for the determination of the heat of combustion of building products at constant volume in a bomb calorimeter. This European Standard describes a test method for the measurement of the gross heat of combustion (PCS). Annex A describes the calculation of the net heat of combustion (PCI) when required. Information on the precision of the test method is given in Annex B.

Reaction to fire tests for building products - Determination of the heat of combustion

ASTM C4-02 粘土和多孔粘土排水管的标准规范

1.1 This specification establishes the criteria for acceptance, prior to installation, of drain tile and perforated drain tile to be used for underdrainage, filter fields, leaching fields, and similar subdrainage installations.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 The following safety hazards caveat pertains only to the Test Methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;Attention is called to Test Methods C 301 and Terminology C 896.

Standard Specification for Clay Drain Tile and Perforated Clay Drain Tile

BS 6463-102:2001 生石灰、熟石灰与天然碳酸钙.化学分析方法

This part of BS 6463 describes methods for the chemical analysis of quicklime, hydrated lime and natural calcium carbonate. It describes both classical methods and methods which use atomic absorption spectrometry (AAS). It gives classical chemical methods for: —fluorine, matter insoluble in acetic acid, matter insoluble in hydrochloric acid; —loss on ignition, neutralizing value; —free water in hydrated lime and also in lime putty; —total sulfur; —carbon dioxide in carbonate. It gives flame atomic absorption spectrometric (AAS) methods for aluminium, cadmium, chromium, cobalt, copper, iron, lead, magnesium, manganese, nickel, silicon, silver and zinc.

Quicklime, hydrated lime and natural calcium carbonate - Methods for chemical analysis

JC/T 876-2001 煅烧α-氧化铝

Calcinated α-alumina

ISO 13788:2001 建筑部件和构件的湿热性能 能避免临界表面湿度和缝隙冷凝作用的内表面温度 计算方法

This standard gives calculation methods for: a) The internal surface temperature of a building component or building element below which mould growth is likely, given the internal temperature and relative humidity - the method can also be used to assess the risk of other surface condensation problems. b) The assessment of the risk of interstitial condensation due to water vapour diffusion. The method used assumes built-in water has dried out and does not take account of a number of important physical phenomena including: - the dependence of thermal conductivity on moisture content; - the release and absorption of latent heat; - the variation of material properties with moisture content; - capillary suction and liquid moisture transfer within materials; - air movement through cracks or within air spaces; - the hygroscopic moisture capacity of materials. Consequently the method is applicable only to structures where these effects are negligible.

Hygrothermal performance of building components and building elements - Internal surface temperature to avoid critical surface humidity and interstitial condensation - Calculation methods

ISO 3869:2001 复合软木 膨胀连接填充料 规范、包装和贴标志

This International Standard specifies the characteristics of composition cork intended to be used as expansion joint filler between concrete or other construction products.

Composition cork - Expansion joint fillers - Specifications, packaging and marking

JC/T 409-2001 硅酸盐建筑制品用粉煤灰

Fly ash for silicate building products

KS F 4425-2001 桥梁用伸缩接口装置试验方法

이 규격은 도로와 교량의 상부가 접하는 위치나 상부 구조가 분리되는 위치에 설치하여 구조물

Testing method for bridge expansion joint

ANSI/EIMA 99-A-2001 外部绝缘和终饰系统(EIFS)

Provides the requirements for specifying and installing Exterior Insulation and Finish Systems This standard was listed for public review in the 5/5/2000 issue of Standards Action. It is being resubmitted due to substantive changes to the text.

Exterior Insulation and Finish Systems (EIFS)

CSA A277-01-CAN/CSA-2001 工厂建房认证程序.第4版.1号通用指令.2号更新

Procedure for Certification of Factory-Built Houses Fourth Edition; General Instruction No 1; Update No 2

Procedure for Certification of Factory-Built Houses Fourth Edition; General Instruction No 1; Update No 2