Q12 水泥混合材与外加剂 标准查询与下载

ASTM C1738-11 水凝水泥糊剂的高剪切混合用标准实施规程

This practice is useful in laboratory research on rheology of hydraulic cement systems as it has been shown to provide a paste with rheological properties similar to those obtained in a concrete from which the aggregate had been removed. Mixing of paste using C305 is not satisfactory as the paste is not thoroughly mixed, due to the absence of sand. In this practice the shear imparted to the cement paste is significantly higher than in C305 and therefore it is known as high-shear mixing.1.1 This practice covers the high-shear mixing of hydraulic cement pastes. 1.2 The values stated in SI units or inch-pound units are to be regarded as the standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for High-Shear Mixing of Hydraulic Cement Pastes

ASTM C1438-11a 水凝水泥混凝土和砂浆的胶乳和粉状聚合物调节剂标准规范

1.1 This specification covers performance criteria for latexes and redispersible powders when used as modifiers in hydraulic cement concretes and mortars to improve adhesion and reduce permeability (see Note 1). Note 18212;For further information concerning theory, benefits, limitations, and applications of polymer-modified hydraulic cementitious mixtures, refer to ACI 548.3R-09. 1.2 The performance criteria are based on certain property changes that are achieved by use of the polymer modifier when compared to reference concrete or mortar (Test Methods C1439). 1.3 Prepackaged, proprietary mortar products are not included in this specification. Also, this specification covers only those materials contained in the reference or test mixtures listed in Test Methods C1439. 1.4 The values stated in SI units are to be regarded as standard. 1.5 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Latex and Powder Polymer Modifiers in Hydraulic Cement Concrete and Mortar

JC/T 2031-2010 水泥砂浆防冻剂

本标准规定了水泥砂浆防冻剂的术语和定义、分类、要求、试验方法、检验规则、包装、运输、出厂与贮存。 本标准适用于最低使用温度为-5℃、-10℃的水泥砂浆防冻剂。

Anti-freezing admixture for cement mortar

JC/T 2030-2010 预制混凝土衬砌管片生产工艺技术规程

本标准规定了盾构施工法用预制混凝土衬砌管片产品制造过程中的各工序的工艺技术要求，包括原材料、钢筋骨架、混凝土、模具及组装、成型、蒸汽养护、脱模、修补、后期养护、检验、标志、防腐、产品贮存及运输等。 本标准适用于以钢筋、混凝土为主要原料制成的用于轨道交通、公路、铁路、水工、电力、市政等隧道工程的预制混凝土衬砌管片。

Technical rules of reinforced concrete segments

JG/T 270-2010 工业构筑物水泥基耐磨材料

本标准规定了工业构筑物水泥基耐磨材料的术语和定义、技术要求、试验方法、检验规则以及包装、标志、运输和贮存。 本标准适用于冲渣沟、储仓、下料斗、矿槽等工业构筑物用耐磨面层的水泥基材料。

Cement based wear resisting material

SANS 6152:2010 水泥掺合料的有效碱含量（与SANS 50197-1标准一致）

Describes a method to determine the available alkali content of cement extenders (complying with SANS 50197-1).

Available alkali content of cement extenders (complying with SANS 50197-1)

ASTM C1240-10a 硅粉使用碳化混合物标准规格

1.1 This specification covers silica fume for use in concrete and other systems containing hydraulic cement. 1.2 In the cases of slurried or densified silica fume, perform the tests on the raw silica fume from which these products have been made. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test methods portions, Sections 10-19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Read the material safety data sheets for materials used. 1.5 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this standard.

Standard Specification for Silica Fume Used in Cementitious Mixtures

ASTM C465-10 水凝水泥制造用处理添加剂的标准规范

1.1 This specification pertains to the criteria and tests to be used for determining whether a(n) organic or inorganic processing addition, when used in the recommended amount at the option of the cement producer in the manufacture of hydraulic cements, meets the requirements as prescribed by definition in Specifications C150, C1157, C845, and C595. The materials listed in the following former ASTM Specifications shall be considered as meeting the organic processing additions requirements of this specification: C150 – 62, for Portland Cement – 58 T, for Portland Blast-Furnace Slag Cement – 58 T, for Portland Pozzolan Cement – 58, for Slag Cement 1.2 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements

ASTM C1622/C1622M-10 低温混合系统的标准规范

1.1 This specification covers cold-weather admixture systems to be added to hydraulic-cement concrete when the temperature of the concrete immediately after placement will be as low as -5.0 °C [23.0 °F] prior to the time of initial set. 1.2 This specification stipulates tests of the cold-weather admixture system with suitable materials as described in 11.1-11.3 or with materials proposed for specific work (See 11.5). Unless otherwise requested by the purchaser, tests shall be made using suitable concreting materials as described in 11.1-11.3. Note 18212;Whenever practicable, tests should be made using the concreting materials, the mixture proportions, and batching sequence proposed for the specific work (See 11.5) because the time of setting, compressive strength gain, and other properties may vary. 1.3 This specification provides three levels of testing. 1.3.1 Level 18212;During the initial approval stage, proof of compliance with the performance requirements defined in Table 1 demonstrates that the cold-weather admixture system meets the requirements of this specification. Uniformity and equivalence tests (See Section 6) shall be carried out to provide results against which later comparisons can be made. nbsp;nbsp;nbsp; 1.3.2 Level 28212;Limited retesting is described in 5.2, 5.2.1, and 5.2.2. Proof of compliance with the requirements of Table 1 demonstrates conformity of the admixture system with the requirements of this specification. 1.3.3 Level 38212;For acceptance of a lot or for measuring uniformity within or between lots, when specified by the purchaser, uniformity and equivalence tests (See Section 6) shall be used. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The text of this standard references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 The following precautionary caveat pertains to the test methods portion, Sections 11-18, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. WARNINGFresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.

Standard Specification for Cold-Weather Admixture Systems

ASTM C1240-10 硅粉使用碳化混合物标准规格

1.1 This specification covers silica fume for use in concrete and other systems containing hydraulic cement. 1.2 In the cases of slurried or densified silica fume, perform the tests on the raw silica fume from which these products have been made. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test methods portions, Sections 10-19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Read the material safety data sheets for materials used. 1.5 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this standard.

Standard Specification for Silica Fume Used in Cementitious Mixtures

JC/T 874-2009 水泥用硅质原料化学分析方法

本标准规定了配制水泥生料用硅质原料的化学分析方法。本标准中除氧化钾和氧化钠的测定外，其它化学成分的测定包含基准法和代用法两种方法，可根据实际情况任选。在有争议时，以基准法为准。 本标准适用于配制水泥生料用硅质原料的化学分析。

Methods of chemical anaylsis of silicious raw materials for cement industry

JC/T 850-2009 水泥用铁质原料化学分析方法

本标准规定了配制水泥生料用铁质校正原料的化学分析方法。本标准中对二氧化硅、三氧化二铁、三氧化二铝和三氧化硫等四种化学成分的测定包含基准法和代用法两种方法，可根据实际情况任选。在有争议时，以基准法为准。 本标准适用于水泥生产用铁矿石、硫酸渣等铁质校正原料的化学分析。

Methods of chemical analysis of iron raw materials for cement industry

BS EN 934-2:2009+A1:2012 混凝土, 灰浆和灌浆外加剂. 混凝土外加剂. 定义, 要求, 一致性, 标记和标签

Admixtures for concrete, mortar and grout. Concrete admixtures. Definitions, requirements, conformity, marking and labelling

BS EN ISO 10426-6:2008 石油和天然气工业.固井用水泥和材料.水泥加工制剂的静态胶凝强度的测定方法

Petroleum and natural gas industries - Cements and materials for well cementing - Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)

JC 506-2008 无声破碎剂

本标准规定了无声破碎剂的术语和定义、分类、技术要求、试验方法、检验规则、包装、标志、运输和贮存等。 本标准适用于无声破碎剂的生产、检验和验收，有关使用和安全注意事项参见附录B。

Soundless cracking agent

JC/T 407-2008 加气混凝土用铝粉膏

本标准规定了湿法磨制铝粉膏（以下简称铝粉膏）的分类与标记、技术要求、试验方法、检验规则及包装、贮存与运输等。 本标准适用于作为加气混凝土铝粉膏。

Aluminium pastes for aerated concrete

JC/T 474-2008 砂浆、混凝土防水剂

Mortar, concrete waterproofing agent

JC 474-2008 砂浆、混凝土防水剂

本标准规定了砂浆、混凝土防水剂的术语和定义、要求、试验方法、检验规则、产品说明书、包装、出厂、运输和贮存。 本标准适用于砂浆和混凝土防水剂。

water-repellent admixture for mortar and concrete

JC/T 506-2008 无声破碎剂

Silent breaker

JIS A 6202 AMD 1:2008 混凝土用膨胀掺合剂(修改件1)

This standard is an Amendment of Expansive additive for concrete.

Expansive additive for concrete (Amendment 1)