Q17 屋面、铺面防水与防潮材料 标准查询与下载
共找到 1393 条与 屋面、铺面防水与防潮材料 相关的标准，共 93 页
This European Standard specifies a test method to determine the adhesion/cohesion properties after immersion in test fuels or liquid chemicals.
Cold applied joint sealants - Test method - Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals
- ICS
- 93.080.20
- CCS
- Q17
- 发布
- 2017-03
- 实施
This European Standard specifies a test method for the evaluation of the compatibility of the waterproofing system applied to a concrete surface and covered with an asphalt layer. The complete system is exposed to an accelerated heat conditioning followed by a determination of the shear strength properties before and after heat conditioning.
Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Compatibility by heat conditioning
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2017-03
- 实施
This European Standard specifies a test method for the evaluation of the resistance to impact puncturing of a sheet or sheet system.
Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of resistance to dynamic water pressure after damage by pre-treatment
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2017-03
- 实施
This European Standard describes a test method for evaluating the resistance of cold applied joint sealants to the action of UV-light by determination of the change of physical properties after irradiation by artificial UV-light.
Cold applied joint sealants - Test methods - Part 8: Determination of the artificial weathering by UV-irradiation
- ICS
- 93.080.20
- CCS
- Q17
- 发布
- 2017-03
- 实施
Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking
- ICS
- 91.100.25;91.100.50
- CCS
- Q17
- 发布
- 2017-02-28
- 实施
- 2017-02-28
This European Standard applies to all liquid-applied water impermeable products, based on polymer modified cementitious mortars, dispersions and reaction resin coatings, used beneath ceramic tiling, for external tile installations on walls and floors and in swimming pools. This European Standard gives the terminology concerning the products and specifies the test methods and the values of performance requirements for liquid-applied water impermeable products associated with tile adhesives. This European Standard specifies the assessment and verification of constancy of performance, and the classification and marking of liquid-applied water impermeable products beneath ceramic tiling. This European Standard does not contain recommendations for the design and installation of ceramic tiles and grouts in combination with water impermeable products. NOTE Liquid-applied water impermeable products may also be used beneath other types of tiles (natural and agglomerated stones, etc.), where they do not adversely affect these materials.
Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives - Requirements@ test methods@ assessment and verification of constancy of performance@ classification and marking
- ICS
- 91.100.23;91.100.25;91.100.50
- CCS
- Q17
- 发布
- 2017-02
- 实施
1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface. This specification does not include specific requirements for skid resistance or fire retardance, although both may be important in specific uses. 1.2 The type of membrane system described in this specification is used for pedestrian and vehicular traffic and in high-abrasion applications. The membrane may be single- or multi-component, and may consist of one or more coats (for example base coat, top coat, etc.). The coat(s) may be built to the desired thickness in one or more applications. One coat (base coat) provides the primary waterproofing function and normally comprises the major amount of organic material in the membrane. The function of the top coat(s) is to resist wear and weather. Aggregate may be used as a component of the membrane system, as all or part of a course, to increase wear and skid resistance. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.4 Test methods in this specification require a minimum 0.5-mm [0.020-in.] base coat dry film thickness. Actual thickness required for a particular application and the use of aggregate in topcoats shall be established by the membrane manufacturer. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 The following safety hazards caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing Surface
- ICS
- 83.060 ; 91.100.50
- CCS
- Q17
- 发布
- 2017
- 实施
1.1 This specification covers the types, physical properties, and dimensions of rigid cellular polystyrene intended for use as geofoam. 1.2 This specification does not cover the layout, placement, and workmanship for proper installation and performance of rigid cellular polystyrene geofoam. 1.3 Rigid cellular polystyrene geofoam covered by this specification may need protection from certain chemicals, environmental exposure, and concentrated loads. Additional design considerations may include thermal conductivity and buoyancy. Guidelines regarding these end-use considerations are included in Appendix X1. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Rigid Cellular Polystyrene Geofoam
- ICS
- 59.080.70 ; 83.100
- CCS
- Q17
- 发布
- 2017
- 实施
1.1 This specification covers asphalt-saturated organic felts, with or without perforations, intended to be used with asphalts conforming to the requirements of Specification D312/D312M in the construction of built-up roofs, and with asphalts conforming to the requirements of Specification D449/D449M in the construction of water proofing systems. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2017
- 实施
Resilient floor coverings. Specification for floor panels/assembly for loose laying
- ICS
- 97.150
- CCS
- Q17
- 发布
- 2016-12-31
- 实施
- 2016-12-31
Simultaneous grouting materials for shield tunneling
- ICS
- 91.120.30
- CCS
- Q17
- 发布
- 2016-09-28
- 实施
- 2016-12-10
Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules; German version EN 12039:2016
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2016-09
- 实施
This European Standard classifies thermosetting resin based wood adhesives for non-structural applications into durability classes C1 to C4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments. For special applications, further tests, which do not fall within the scope of this European Standard can be applicable. The adhesives specified in this European Standard are suitable for the bonding of furniture and interior structures, panelling, doors, windows, stairs etc. made of wood or derived timber products.
Classification of thermosetting wood adhesives for non-structural applications
- ICS
- 83.180
- CCS
- Q17
- 发布
- 2016-08
- 实施
Flexible sheets for waterproofing. Bitumen sheets for roof waterproofing. Determination of adhesion of granules
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2016-06-30
- 实施
- 2016-06-30
This European Standard applies to the apparatus and the test procedure used for the determination of the adhesion of granules to factory made bituminous sheets for roofing. It can also be used in other areas where it is relevant.
Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules
- ICS
- 91.100.50
- CCS
- Q17
- 发布
- 2016-06
- 实施
This European Standard specifies the requirements for pipes, fittings, brackets and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater piping systems. It also specifies: a) The requirements for metallic brackets. b) Both solid wall pipes and fittings, (i.e. product manufactured from a single layer), as well as solid wall multi-layer pipes. c) The test parameters for the test methods referred to in this standard. Pipes can be used in conjunction with fittings and brackets of acrylic materials provided these polymers meet the performance requirements of this standard. The products are usually used in conjunction with gutters conforming to EN 607. They are not intended for use with products conforming to EN 612. This standard is applicable to PVC-U rainwater systems of circular, square, rectangular or any other shape with sealed (rubber ring or solvent cement) or unsealed joints. This standard covers a range of pipes and fittings sizes. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from the size range to take into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 The term "rainwater" in this standard is used also to encompass "surface water" (as defined in EN 752) run-off from buildings.
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes@ fittings and the system
- ICS
- 23.040.05;23.040.20
- CCS
- Q17
- 发布
- 2016-04
- 实施
This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without thermoplastics lining for storage or processing of fluids, factory made or site built, non-pressurized or pressurized up to 10 bar, for use above ground. Further requirements are presented in normative Annex G. The terms vessels and tanks as used in this part of EN 13121 include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell. This part of EN 13121 covers vessels and tanks subject to temperatures between - 40 °C and 120 °C. Excluded from this part of EN 13121 are: - tanks and vessels for the transport of fluids; - underground storage tanks; - spherical vessels; - vessels and tanks of irregular shape; - tanks and vessels with double containment where the double wall is considered structural; - tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity; - specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280).
GRP tanks and vessels for use above ground - Part 3: Design and workmanship
- ICS
- 23.020.10
- CCS
- Q17
- 发布
- 2016-04
- 实施
Test methods -- Resilient floorcoverings
- ICS
- 59.080.60;91.060.30;97.150
- CCS
- Q17
- 发布
- 2016-03-22
- 实施
