Q45 定型隔热耐火材料 标准查询与下载

YB/T 4016-1991 玻璃熔窖用耐火制品抽样的验收方法

Method for acceptance of samples of refractory products for glass melting kilns

BS 7225-3.1:1990 耐火材料分类.陶瓷纤维制品.覆盖层、底板、毡垫和纸

Classifies on the basis of physical and chemical properties.

Classification of refractories - Ceramic fibre products - Blankets, mats, felts and paper

ASTM F1312-90(2007) 高温隔热耐火粘土砖的标准规范

1.1 This specification covers one type of thermal insulating brick for use as backup insulation for refractory furnace linings of boiler furnaces.1.2 The values stated in inch-pound units are to be regarded as standard. The SI units in parentheses are for information purposes only and may be approximate.

Standard Specification for Brick, Insulating, High Temperature, Fire Clay

ASTM F1312-90(2002) 高温隔热耐火粘土砖的标准规范

1.1 This specification covers one type of thermal insulating brick for use as backup insulation for refractory furnace linings of boiler furnaces.1.2 The values stated in inch-pound units are to be regarded as standard. The SI units in parentheses are for information purposes only and may be approximate.

Standard Specification for Brick, Insulating, High Temperature, Fire Clay

NF B40-312:1989 耐火产品.致密,隔热成型产品.测定超声波传输过程中的传播速度

Refractory products - Dense,insulating shaped products - Determination of ultrasonic propagation vetocity in transmission

Refractory products - Dense,insulating shaped products - Determination of ultrasonic propagation vetocity in transmission

NF B40-311:1989 耐火产品.密实,绝缘定型产品.通过机械冲击进行谐振频率测定

Refractory products - Dense,insulating shaped products - Determination of the resonance frequency through mechanical impacting

Refractory products - Dense,insulating shaped products - Determination of the resonance frequency through mechanical impacting

ASTM C182-88(2013) 绝热耐火砖的热传导性的标准试验方法

3.1 The thermal conductivity of insulating firebrick (IFB) is a property required for the selection of IFB for a specific thermal performance. Users select brick to provide a specified heat-loss and cold-face temperature without exceeding the temperature limitation of the brick. This test method establishes placement of thermocouples and the positioning of test samples in the calorimeter. This test method must be used with Test Method C201. 1.1 This test method supplements Test Method C201, and shall be used in conjunction with that test method to determine the thermal conductivity of insulating firebrick. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Conductivity of Insulating Firebrick

ASTM C182-88(2009) 绝热耐火砖的热传导性的标准试验方法

The thermal conductivity of insulating firebrick (IFB) is a property required for the selection of IFB for a specific thermal performance. Users select brick to provide a specified heat-loss and cold-face temperature without exceeding the temperature limitation of the brick. This test method establishes placement of thermocouples and the positioning of test samples in the calorimeter. This test method must be used with Test Method C 201. 1.1 This test method supplements Test Method C 201, and shall be used in conjunction with that test method to determine the thermal conductivity of insulating firebrick. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Conductivity of Insulating Firebrick

ASTM C182-88(2004) 绝热耐火砖的热传导性的测试方法

The thermal conductivity of insulating firebrick (IFB) is a property required for the selection of IFB for a specific thermal performance. Users select brick to provide a specified heat-loss and cold-face temperature without exceeding the temperature limitation of the brick. This test method establishes placement of thermocouples and the positioning of test samples in the calorimeter. This test method must be used with Test Method C 201. 1.1 This test method supplements Test Method C201, and shall be used in conjunction with that test method to determine the thermal conductivity of insulating firebrick. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Conductivity of Insulating Firebrick

JC/T 804-1987 水泥窑用陶粒轻质耐火混凝土砌块

Lightweight and refractory ceramsite concrete block for cement kiln lining

BS 3056-8:1987 耐火砖尺寸.第8部分:钢铁水包用砖规范

Dimensions of refractory bricks for use in the construction of ladles used during the manufacture of iron and steel.

Sizes of refractory bricks - Specification for bricks for ladles

BS 3056-3:1986 耐火砖尺寸.第3部分:旋转水泥窑用耐火砖规范

All types of refractory products used in this application. Tolerances on dimensions are also given, along with design information and recommended ratios for 2-taper lining.

Sizes of refractory bricks - Specification for bricks for rotary cement kilns

BS 3056-1:1985 耐火砖尺寸.第1部分:多用途耐火砖规范

Shapes and sizes of refractory bricks that are used in a wide range of industrial applications in high temperature manufacturing processes.

Sizes of refractory bricks - Specification for multi-purpose bricks

BS 3056-2:1985 耐火砖尺寸.第2部分:玻璃熔炉用耐火砖规范

This Part of BS 3056 specifies the sizes of the following shapes of refractory bricks for glass-melting furnaces: (a) squares; (b) splits; (c) tiles; (d) blocks; (e) straights; (f) side arch bricks; (g) end arch bricks; (h) crown bricks. NOTE 1. Information is also given on the combinations of size and material/quality that may be expected to be available, on arch-brick formulae (see appendix A), on the combinations of sizes required to form circles of various diameters (see appendix B), and on informa-tion to be supplied by a purchaser (see appendix C). The volume of each standard size brick is given as supplementary information, in tables 1 to 8. NOTE 2. The tolerances on the sizes are not specified in this Part of BS 3056, and may be the subject of agreement between manufacturer and purchaser. NOTE 3. The titles of the publications referred to in this standard are listed on the inside back cover.

Sizes of refractory bricks - Specification for bricks for use in glass-melting furnaces

BS 3056-4:1985

Specifies the dimensions of refractory bricks for use in the construction of the roofs of electric arc furnaces.

JIS R 2614:1985 隔热耐火砖比重及真气孔率的试验方法

この規格は，耐火断熱れんがの次の各項の試験方法について規定する。

Testing method for specific gravity and true porosity of insulating fire bricks

ISO 5019-6:1984 耐火砖 尺寸 第6部分:吹氧炼钢转炉用的衬砖

Briques réfractaires - Dimensions - Partie 6 : Briques basiques pour convertisseurs à oxygène (Première édition)

NF B40-007:1984 耐火材料.定型绝缘产品的分类.

Refractories - Classification of shaped insulating products.

Refractories - Classification of shaped insulating products.

NF B40-008:1984 耐火材料.致密定形耐酸产品的分类.

Refractories - Classification of dense shaped anti-acid products.

Refractories - Classification of dense shaped anti-acid products.

BS 1902-3.11:1983 耐火材料试验方法.一般特性和结构特性.耐火砖尺寸规格与形状测量(1902-311法)

Details the methods for measuring refractory bricks and blocks, and for determining their errors of shape, for use when circumstances do not warrant the use of more elaborate methods.

Methods of testing refractory materials - General and textural properties - Measurement of dimensions and shape of refractory bricks and blocks (methods 1902-311)