Q83 供热器材设备 标准查询与下载

BS EN 50379-1:2012 用于加热器具燃烧废气参数测量的便携式电气装置规格.第1部分:通用要求和试验方法

Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. General requirements and test methods

BS EN 50379-3:2012 加热设施的燃烧排气参数测量用便携式电器规格.燃气式加热装置的非规定操作用装置的性能要求

Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. Performance requirements for apparatus used in non-statutory servicing of gas fired heating appliances

BS EN 50379-2:2012 加热设施的燃烧排气参数测量用便携式电器规格.用于法定检测和评估的仪器性能要求

Specification for portable electrical apparatus designed to measure combustion flue gas parameters of heating appliances. Performance requirements for apparatus used in statutory inspections and assessment

JIS B 8407-1:2012 强制送风燃烧器.第1部分:气体燃烧器

Forced draught burners -- Part 1: Gas burners

JIS B 8407-2:2012 强制送风燃烧器.第2部分:燃油器

Forced draught burners -- Part 2: Oil burners

ANSI Z21.98-2012 热水器内非金属液面探测管标准

This standard applies to newly produced non-metallic dip tubes intended for use in water heaters.

Standard for Nonmetallic Dip Tubes For Use In Water Heaters (same as CSA 4.10)

ANSI Z83.18-2012 再循环直接燃气式工业气体加热器

Non-Recirculating Direct Gas-Fired Industrial Air Heaters

ANSI Z21.47-2012 燃气集中供热炉(同CSA 2.3)

This standard applies to automatically operating gas-fired central furnaces for installation in residential, commercial, and industrial structures including furnaces for Direct Vent, Recreational Vehicle, Outdoor, and Manufactured (Mobile) Homes. These furnaces may include a cooling unit.

Gas-Fired Central Furnaces (same as CSA 2.3)

ANSI/ASHRAE 118.1-2012 燃气、电力和燃油热水器额定值的测试方法

Method of Testing for Rating Commercial Gas, Electric and Oil Service Water Heating Equipment

ANSI/NSF 5(i7)-2012 热水器,热水供给锅炉,和热回收设备

Water heaters, hot water supply boilers, and heat recovery equipment

ANSI/UL 180a-2012 油燃烧器和其他可燃液体的液位指示器的安全性标准(公告日期2012年8月17日)

Standard for Safety for Liquid-Level Gauges for Oil Burner Fuels and Other Combustible Liquids (Bulletin dated August 17, 2012)

ANSI Z21.98a-2012 热水器内非金属液面探测管标准

Standard for Non-Metallic Dip Tubes for Use in Hot Water Heaters

ANSI/UL 180-2012 油燃烧器和其他可燃液体的液位指示器的安全性标准(公告日期2012年3月9日)

Standard for Safety for Liquid-Level Gauges for Oil Burner Fuels and Other Combustible Liquids (Bulletin dated March 9, 2012)

ANSI Z21.50-2012 排气壁炉标准(同CSA 2.22)

Standard For Vented Gas Fireplaces (same as CSA 2.22)

ASTM E2816-12a 防火金属采暖通风与空调管道系统的标准试验方法

1.1 Resist the effects of a standardized fire exposure, and 5.1.2 Retain its integrity. 5.2 These test methods provide for the following measurements and evaluations where applicable: 5.2.1 Ability of the fire-resistive material to resist flaming (combustion) when exposed to 1382??F (750??C). 5.2.2 Ability of the tested support system to carry the load of the HVAC duct and its fire-resistive material(s) during a standardized fire-engulfment test. 5.2.3 Ability of the firestops to meet the requirements of Test Method E814 when used as part of a HVAC duct system. 5.2.4 Ability of the HVAC duct system to resist the passage of flames and hot gases onto its unexposed surface during a standardized fire-resistance test. 5.2.5 Transmission of heat through the HVAC duct system during a standardized fire-resistance test. 5.2.6 Ability of the firestop to resist the passage of water during a standardized hose stream test. 5.2.7 Comparative measurement of temperature aging of the fire-resistive material(s) when subjected to a standardized thermal cycling during the durability test. 5.2.8 Measurement of flame spread over the surface of the fire-resistive material or HVAC duct system. 5.2.9 Ability of the covering and lining to resist flaming, glowing, smoldering or smoking while in service. 5.3 These test methods do not provide the following: 5.3.1 Full information as to performance of the fire-resistive material, supporting construction, or the HVAC duct system constructed with components, densities, or dimensions other than those tested. 5.3.2 Evaluation of the degree by which the fire-resistive material or HVAC duct system contributes to the fire hazard by generation of toxic gases, or other products of combustion. 5.3.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the HVAC duct system. 5.4 The test specimens are subjected to one or more specific tests under laboratory conditions. When different test..........

Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems

ASTM E2816-12 防火金属采暖通风与空调管道系统的标准试验方法

1.1 Resist the effects of a standardized fire exposure, and 5.1.2 Retain its integrity. 5.2 These test methods provide for the following measurements and evaluations where applicable: 5.2.1 Ability of the fire-resistive material to resist flaming (combustion) when exposed to 1382??F (750??C). 5.2.2 Ability of the tested support system to carry the load of the HVAC duct and its fire-resistive material(s) during a standardized fire-engulfment test. 5.2.3 Ability of the firestops to meet the requirements of Test Method E814 when used as part of a HVAC duct system. 5.2.4 Ability of the HVAC duct system to resist the passage of flames and hot gases onto its unexposed surface during a standardized fire-resistance test. 5.2.5 Transmission of heat through the HVAC duct system during a standardized fire-resistance test. 5.2.6 Ability of the firestop to resist the passage of water during a standardized hose stream test. 5.2.7 Comparative measurement of temperature aging of the fire-resistive material(s) when subjected to a standardized thermal cycling during the durability test. 5.2.8 Measurement of flame spread over the surface of the fire-resistive material or HVAC duct system. 5.3 These test methods do not provide the following: 5.3.1 Full information as to performance of the fire-resistive material, supporting construction, or the HVAC duct system constructed with components, densities, or dimensions other than those tested. 5.3.2 Evaluation of the degree by which the fire-resistive material or HVAC duct system contributes to the fire hazard by generation of toxic gases, or other products of combustion. 5.3.3 Measurement of the degree of control or limitation of the passage of smoke or products of combustion through the HVAC duct system. 5.4 The test specimens are subjected to one or more specific tests under laboratory conditions. When different test conditions are substituted or the end-use conditions are changed, it is not always possible by, or from, these test methods to predict changes to the characteristics measured. Therefore,..........

Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems

ANSI/UL 174a-2012 家用电器储存罐式热水器安全性标准(提案日期07-13-12)

Standard for Safety for Household Electric Storage Tank Water Heaters (Proposal document dated 07-13-12)

ANSI/ASTM F1602:2012 地板和墙上直接安装的气体点火和电子点火的20到200 Gal(75.7到757 L)加罩蒸汽壶规格

Specification for Kettles, Steam-Jacketed, 20 to 200 Gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated

ANSI/ASTM F1603:2012 倾斜台式直接安装的气体点火和电子点火的32 Oz到20 Gal(1到75.7L)加罩蒸汽壶规格

Specification for Kettles, Steam-Jacketed, 32 oz to 20 Gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated

ANSI Z21.88a-2012 开通风孔的气体壁炉加热器(与CSA 2.33相同)

Standard for Vented Gas Fireplace Heaters (same as CSA 2.33)