T00 标准化、质量管理 标准查询与下载

GOST R 51814.1-2009 质量管理体系.ISO 9001-2008应用于汽车产品和相关工作部件构造的详细要求/注:代替GOST R 51814.1(2004).

Quality management systems. Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations

KS B ISO 17900:2008 农用挂车.带平衡装置的半悬挂式挂车.有效负载、垂直静止负载及轴载的测定

이 표준은 빈 트레일러의 무게를 측정하고 그 요구사항을 추정함으로써 농업용 반장착형 및 대

Agricultural trailers－Balanced and semi-mounted trailers－Determination of payload, vertical static load and axle load

GA 803-2008 车辆和驾驶人管理印章

Vehicle and Driver Management Seal

CNCA 02C-023-2008 机动车辆类强制性认证实施规则 汽车产品

本规则适用于可在中国公路及城市道路上行驶的M类汽车、N类汽车和O类挂车（包括完整的或不完整的）。 不适用于在轨道上行驶的车辆、农业与林业用拖拉机和各种工程机械以及其他非道路车辆和三类底盘。

Implementation Rules for Compulsory Certification of Motor Vehicles Automobile Products

BS ISO 10521-2:2006 道路车辆.道路阻力加载.底盘测功机上的再现

This part of ISO 10521 specifies methods of setting the target road load on chassis dynamometers for the purpose of a subsequent test, for example the fuel consumption test or the exhaust-emission measurement test. The road-load setting method on chassis dynamometers depends on the road-load measurement method, such as the coastdown method, the torquemeter method or the wind-tunnel and chassis-dynamometer method. This part of ISO 10521 gives detailed instructions on the methods of the chassis-dynamometer setting procedure for road-load value, obtained by the various measurement methods specified in ISO 10521-1. This part of ISO 10521 is applicable to chassis dynamometers that can set road load at a minimum of three speed points, and to motor vehicles as defined in ISO 3833 up to a gross vehicle mass of 3 500 kg.

Road vehicles - Road load - Reproduction on chassis dynamometer

BS ISO 10521-1:2006 道路车辆.道路阻力加载.在参照大气条件下的测定

This part of ISO 10521 specifies methods of determining the road load of road vehicles for subsequent test purposes, for example, fuel consumption tests or exhaust emission measurements. This determines the road load of a vehicle running on a level road under reference atmospheric conditions. It is achieved by either the coastdown method, the torquemeter method or the wind-tunnel/chassis-dynamometer method. This part of ISO 10521 is applicable to motor vehicles, as defined in ISO 3833, up to a gross vehicle mass of 3 500 kg.

Road vehicles - Road load - Determination under reference atmospheric conditions

CNCA 02C-026-2005 机动车辆类强制性认证实施规则 汽车安全带产品

本规则适用于安装在M和N类汽车上，且由前向成年乘员作为独立装备单独使用的安全带和约束系统。

Implementation Rules for Compulsory Certification of Motor Vehicles Car Seat Belt Products

SAE J706-2003 绞车评级

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for free-spooling may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control free-spooling, but will be relied on to control or hold a load. Power sources, such as hydraulic motors, even though they may be supplied or recommended by the winch manufacturer, are not considered a part of the winch so far as this document is concerned, except to whatever extent they are a part of the brake system.

Rating of Winches

SAE J2388-2002 二次控制改性

This SAE Recommended Practice establishes a uniform procedure for assuring the manufactured quality, provision for proper installation, and service performance of certain automotive products, specifically, the relocation, alteration, replacement and/or extension of secondary controls and systems.

Secondary Control Modifications

KS Q 10015-2001 质量管理.培训指南

이 규격은 조직에 의하여 공급되는 제품의 품질에 영향을 미치는 교육훈련을 위한 전략과 시스

Quality management－Guidelines for training

NF X50-199:1999 质量体系.汽车供应商.ISO 9001-1994应用的详细要求

Quality systems - Automotive suppliers - Particular requirements for application of ISO 9001-1994

CSA Z605-95-CAN/CSA-1995 车辆占有者的装置及移动设备的装载(MASOR)系统.第1版.通用指令第1-2号

Arrimage Du Moyen De Deplacement Et Dispositif De Retenue De L?Occupant (Systeme MASOR) Pour Les Vehicules Automobiles Premiere Edition; Fiche No 1-2

Shipping System for Automobile Occupant’s Device and Mobile Apparatus (MASOR System).First Edition.General Instruction No 1-2

CSA Z604-95-CAN/CSA-1995 运输移动设备.第1版.通用指令第1-2号

Moyens De Deplacement Transportables Premiere Edition; Fiche No 1-2

Mobile Transportation Equipment.First Edition.General Instruction No 1-2

Q/HBm 95-2001 汽车或发动机配套产品质量控制要求

Quality Control Requirements for Automobile or Engine Supporting Products

DB31/T 127-1994 汽车二级维护质量评定标准

Standards for evaluating the quality of automobile secondary maintenance