T05 专用材料及其制品 标准查询与下载

HG/T 2718-1995 汽车空调用橡胶和塑料软管及软管组合件

本标准规定了供汽车空凋系统用的橡胶或塑料软管和软管组合件的类别、尺寸、结构、技术要求和试验方法等内容。 本标准适用于汽车空调系统输送循环液态和气态二氯二氟甲烷(制冷剂R12)的橡胶和塑料软管和软管组合件。 软管可在-30℃～+125℃的温度范围内使用。

Rubber and plastic hoses and hose assemblies for automotive air conditioners

SAE J1639-1995 汽车聚酰胺(PA)塑料分类系统

This SAE Recommended Practice provides a system for classification and specification for limited number of polyamides (nylons) used in the automotive Industry. Based upon ASTM D 4066, Classification system for nylon Injection and Extrusion Materials (PA), it calls for additional descriptive characteristics and properties commonly used in the automotive Industry. This document applies to natural and non-color matched black, heat- stabilized polyamide compounds only. Color matched compounds shall be defined by the proprietary OEM standards. This document allows for the use of recycled, reconstituted, and regrind materials provided that the requirements as stated in this document are met, the material has not been altered or modified to change its suitability for safe processing and use, and the material shall be identified as such.

Classification System for Automotive Polyamide (PA) Plastics

SAE J1553-1995 粘合纤维增强塑料(FRP)用的车用胶粘剂的交叉剥离试验

This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.

Cross Peel Test for Automotive-Type Adhesives for Fiber- Reinforced Plastic (FRP) Bonding

SAE J1755-1995 汽车外部明亮修剪中使用不锈钢和双金属指南的推荐实施规程.1995年1月

The scope of this SAE Recommended Practice is to give guidelines for design, processing, and material selection for stainless steel and bimetal exterior automotive moldings.

Guidelines for Usage of Stainless Steel and Bimetal for Exterior Automotive Bright Trim, Recommended Practice January 1995

SAE J1767-1995 汽车内饰材料色牢度仪器色差测量的推荐实施规程.1995年1月

The practice described applies to textile and flexible plastic parts and materials used in automotive vehicles. Special care should be taken when high pile carpet samples are being evaluated. The intent of this SAE Recommended Practice is to specify procedures for the instrumental measurement of color differences brought about by the exposure of textile and flexible plastic automotive parts to various colorfastness tests. It may be used for the specification of limits of color differences which may be tolerated in a specific test.

Instrumental Color Difference Measurements for Colorfastness of Automotive Interior Trim Materials, Recommended Practice

SAE J940-1994 碳钢板和钢条术语汇编

This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters nC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.

Glossary of Carbon Steel Sheet and Strip Terms

SAE J217-1994 不锈钢17-7 PH 弹簧钢丝和弹簧

This SAE Recommended Practice covers a high-quality corrosion resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document covers basic processing requirements of springs and forms fabricated from this wire.

Stainless Steel 17-7 PH Spring Wire and Springs

SAE J1679-1994 软修剪胶粘剂抗剥强度的推荐实施规程.1994年4月

This SAE Recommended Practice shall be used to determine the peel strength achieved by an adhesive when used to bond various decorative, flexible substrates such as cloth supported vinyl or carpet, to rigid (steel), semi-rigid (SMC plastic), or other similar substrates.

Peel Strength of Soft Trim Adhesives, Recommended Practice April 1994

SAE J1325-1994 测量灵活绝缘材料相对悬垂性的测试方法

This SAE Recommended Practice describes a method of determining the relative flexibility ofpadding and/or acoustical composites.1.1 Purpose—The purpose of this testing method is to establish a means for measuring the three-dimensionaldrapeability of flexible insulation materials, such as automotive floor pan insulation composites.

Test Method for Measuring the Relative Drapeability of Flexible Insulation Materials

SAE J1700-1994 内饰胶粘剂软化点

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load

Softening Point of Interior Trim Adhesives

SAE J2019-1994 采用一个控制辐照风冷式氙弧装置的汽车外饰材料加速曝光

This SAE Standard specifies the operating procedures for a controlled irradiance, air-cooled xenon-arc apparatus used for the accelerated exposure of various automotive exterior materials. The sample preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.

Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus

ANSI/SAE J369-1994 车内部聚合材料的易燃性.水平测试方法

Flammability of Polymeric Interior Materials - Horizontal Test Method

ASTM A602-94(2004) 汽车用可锻铸铁件的标准规范

1.1 This specification covers castings of ferritic, pearlitic, tempered pearlitic, and tempered martensitic grades of malleable iron used in the products of the automotive and allied industries. Castings shall be heat treated to meet this specification. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Automotive Malleable Iron Castings

ASTM D3836-94(2007) 汽车抛光剂的评定的标准操作规程

This practice is intended to define the properties to be tested, the apparatus to use, and the comparisons of product performance. It is recognized that considerable discretion exists among formulators and marketers of automotive polish on what properties or performance characteristics are best for their products. This practice is flexible enough to honor this fact within the confines of the automotive polish definition below. The test methods are subjective and empirical in order to conform to the basic characteristics of the industry and to allow flexibility in testing.1.1 This practice covers testing properties and apparatus used in evaluating the performance of automotive polishes. This practice is applicable to products that are commonly referred to as car/auto wax, cleaner wax, polish, etc.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluation of Automotive Polish

ASTM A602-94(2009) 汽车用可锻铸铁件的标准规范

1.1 This specification covers castings of ferritic, pearlitic, tempered pearlitic, and tempered martensitic grades of malleable iron used in the products of the automotive and allied industries. Castings shall be heat treated to meet this specification. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Automotive Malleable Iron Castings

SAE J1523-1993 用于汽车型胶粘剂的金属对金属搭接剪切强度测试的推荐实施规程

This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates

Metal to Metal Overlap Shear Strength Test for Automotive Type Adhesives, Recommended Practice

QC/T 80-1993 汽车制动系尼龙管

本标准规定了汽车气制动系尼龙管及管总成的尺寸规格、性能要求和试验方法。 　　本标准适用于在最大工作压力1MPa，温度-40～+100℃的条件下工作的汽车气制动系统使用的尼龙11管及管总成。其它热塑料性材料的管及管总成也可参照执行。 　　本标准不包括汽车气制动系螺旋管的特殊要求。

Automobile brake system nylon tube

QC/T 79-1993 汽车制动系螺旋管

本标准规定了牵引车与半挂车之间汽车气制动系统的廉洁用螺旋管总成的类型、规格尺寸和试验方法。 　　本标准适用于在最大工作压力1Mpa，温度-40～+85℃的条件下工作的牵引车与半挂车之间的气制动系统连接用螺旋管。

Automotive Brake System Spiral Tube

ANSI/SAE J2050-1993 高温助力转向压力软管

This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of -40 to +149 degrees C (-40 to +300 degrees F) maximum and 10.3 MPa (1500 psi) maximum working pressure. these hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

High-Temperature Power Steering Pressure Hose

ISO 3537:1993 道路车辆.安全玻璃材料.机械性能试验

Road vehicles; safety glazing materials; mechanical tests