共找到 66 条与 汽车底盘与车身综合 相关的标准,共 5 页
General technical requirements for low-speed wire-controlled chassis
本文件规定了用于海上滚装船运输的道路车辆上系固设施及系固点型式及布置要求、标记方法、标识与标牌要求。 本文件适用于N2 、N3 和O3 、O4 类车辆(不包括半挂车)及其组成的汽车列车,用于水上滚装船运输的车辆可参照执行。 本文件不适用于半挂车及仅具有牵引功能的专用车辆,也不适用于仅为交付而利用滚装船运送的空载商用车。 注1:对于车辆参数超出一般情况的车辆(特别是质心高度超出正常范围时),需要考虑特殊的系固点的位置和数量。 注2:附录A给出了国际海运组织(IMO)推荐的滚装船上广泛使用的系固设施布置要求。
Lashing and securing arrangements on road vehicles for sea transportation on Ro/Ro ships—General requirements—Part 1:Commercial vehicles and combinations of vehicles,semi-trailers excluded
Protective devices against unauthorized use for all-terrain vehicles
本标准规定了汽车部件可回收利用性标识的要求。 本标准适用于汽车所使用的金属材料部件,质量超过100 g的塑料件,质量超过200 g的橡胶件、热塑性弹性体、复合材料部件,以及其他非金属材料部件。质量小于本标准规定的部件,可参照本标准执行。
Marks for recoverability of automobile parts
本标准规定了与汽车及其零部件产品回收利用相关的术语及定义。 本标准适用于在中国境内使用的各类汽车。
Automobile recovery.Terminology
本标准规定了压缩天然气汽车燃料系统碰撞安全的技术要求和试验方法。 本标准适用于燃料系统采用压缩天然气的M1 类汽车,包括采用两用燃料压缩天然气汽车、单一燃料压缩天然气汽车,其他相关类型车辆也可参照执行。
The safety requirement of fuel system for compressed natural gas vehicle in the collision
本标准规定了客车车身骨架、底架应力、形变测量仪器及辅助器材、测量条件、测量方法、测量结果处理及测量报告内容。 本标准适用于客车车身骨架、底架的应力、形变测量。对于特大型客车车身骨架应力,形变测量也可参照使用。
Measure method of stress and deformation for bus body skeleton
Vehicle and trailer number plate (frame) and its position
本标准规定了汽车和挂车号牌板(架)的形状、尺寸、位置及强度要求。 本标准适用于M、N和O类车辆。
The license plates(crackets)and its position on motor vehicles and trailer
Technical specifications for low-bed semi-trailers
Technical conditions and test methods of aluminum alloy control arm assembly of McPherson suspension for passenger cars
Test methods for performance of automotive interior materials
Special vehicle rear anti-collision energy-absorbing device
Bench test method for fatigue life of front axle horizontal module for passenger cars
本标准适用于汽车悬架用筒式减振器。
Automotive shock absorber performance requirements and bench test methods
Bench test method for fatigue life of torsion beam rear axle for passenger cars
Inspection Regulations for Imported Automobile Parts Aluminum Alloy Wheels
本标准规定了汽车脚踏垫的技术要求、试验方法、检验规则、标识、包装、运输与贮存等要求。 本标准适用于汽车用脚踏垫。
Automotive floor mat
本标准规定了汽车管路保护用热收缩管的要求、试验方法、检验规则以及标识、包装、运输和贮存。 本标准适用于汽车管路保护用热收缩管。
Heat-shrinkable tubing for automotive pipe
本标准规定了汽车用PVC/ABS真空吸塑仪表板表皮的规格、技术要求、试验方法、验收规则及包装、标识、运输、贮存等。 本标准适用于以PVC/ABS,即聚氯乙烯与ABS(丙烯腈-丁二烯-苯乙烯共聚物)共混,以其为主要原料制成的汽车用真空吸塑仪表板表皮(以下简称表皮)。
PVC/ABS vacuum forming skin for automotive instrument panel
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号