T21 传动系统 标准查询与下载
共找到 219 条与 传动系统 相关的标准，共 15 页
The following is a list of the most common terminology used in describing automatic transmission functions.
Automatic Transmission Functions Terminology
- ICS
- 01.040.43;43.040.50
- CCS
- T21
- 发布
- 1994-03-01
- 实施
- 2010-01-08
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this recommended practice may not be commercially available. Availability should be ascertained prior to flywheel design.
Flywheels for Two-Plate Spring-Loaded Clutches
- ICS
- 01.060;43.040.50
- CCS
- T21
- 发布
- 1993-12-01
- 实施
- 2012-06-02
Flywheels for Two-Plate Spring-Loaded Clutches
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1993-12
- 实施
This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data.
Housing Internal Dimensions for Single- and Two-Plate spring-Loaded clutches
- ICS
- 01.060;43.040.50
- CCS
- T21
- 发布
- 1993-04-01
- 实施
Symbols for Hydrodynamic Drives
- ICS
- 01.080.20;21.200
- CCS
- T21
- 发布
- 1993-04
- 实施
Automatic Transmissions - Manual Control Sequence
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1993-04
- 实施
Housing Internal Dimensions for Single- and Two-Plate Spring Loaded Clutches
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1993-04
- 实施
Automatic Transmission Hydraulic Control Systems Terminology
- ICS
- 01.040.43;43.040.50
- CCS
- T21
- 发布
- 1993-04
- 实施
Synchronous belt drives consist of a toothed belt which mates with grooved pulleys to provide a precise speed ratio between the driver and driven pulleys. This SAE Standard covers the synchronous belt and pulley sections currently in use in automotive applications such as camshaft, distributor, and other underhood drives that may require synchronization. It also provides for future sections to be added as usage develops.
SI (Metric) Synchronous Belts and Pulleys
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1993-03-01
- 实施
The following information applies to automotive camshaft drives, distributor drives, or other underhood drives that may require synchronization. For other power transmission drives requiring synchronization, refer to Specifications for Drives using synchronous belts (MXL, XL, L, H, XH and XXH belt sections) (IP 24/1978), published jointly by the Rubber Manufacturers Association (RMA), the mechanical power Transmission Association (MPTA), and the Rubber Association of Canada (RAC).
Automotive Synchronous Belt Drives
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1993-03-01
- 实施
本标准规定了汽车干摩擦式离合器及其组成部件的台架试验方法。 本标准适用于各类汽车干摩擦式离合器。
Automobile dry friction clutch bench test method
- ICS
- CCS
- T21
- 发布
- 1992-07-01
- 实施
- 1993-06-01
本标准规定了汽车干摩擦式离合器总成的技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于汽车干摩擦式离合器总成。
Technical Specifications for Automobile Dry Friction Clutch Assembly (Internal Issue)
- ICS
- CCS
- T21
- 发布
- 1992-07-01
- 实施
- 1993-06-01
本标准规定了载货汽车机械式变速器总成技术要求、试验方法和检验规则。 本标准只适用于载货汽车用机械式四～五档，且四档、五档位直接档的变速器总成。
Specifications for automotive mechanical transmission assembly
- ICS
- CCS
- T21
- 发布
- 1992-04-14
- 实施
- 1993-01-01
本标准规定了十字轴万向节传动轴总成的技术条件。 本标准适用于轻、中型各类汽车及其改装车用传动轴，微型及重型各类汽车及其改装车用传动轴亦可参照使用。
Technical conditions of automobile transmission shaft assembly
- ICS
- CCS
- T21
- 发布
- 1992-04-14
- 实施
- 1993-01-01
本标准规定了汽车液力变速器在台架上的试验方法。 本标准适用于轿车、客车、载货汽车、越野汽车、专用汽车等所用液力变速器。
Bench performance test method for automobile hydraulic transmission
- ICS
- CCS
- T21
- 发布
- 1991-10-07
- 实施
- 1991-11-15
This SAE Recommended Practice applies to flywheels for dry spring-loaded clutches used on internal combustion engines. figure 1 and Tables 1, 2, and 3 report information currently used in the industry. Clutches requiring other dimensions are also manufactured. Dimensions given are primarily for single- plate clutches. Flywheels for two plate clutches have the same dimensions if an adaptor for the intermediate plate and second driven disc is supplied with the clutch. If instead the flywheel is to be extended to adapt the intermediate plate and second driven member, consult the clutch manufacturer for the required J dimensions and drive arrangements for the intermediate plate.
Flywheels for Single-Plate Spring-Loaded Clutches
- ICS
- 01.060;43.040.50
- CCS
- T21
- 发布
- 1991-01-01
- 实施
- 2012-06-02
This SAE Recommended Practice applies to spring-loaded clutches such as are used with manual shift type transmissions.
Spring-Loaded Clutch Spin Test Procedure, Recommended Practice
- ICS
- CCS
- T21
- 发布
- 1990-06-01
- 实施
- 2005-08-16
The following information covers engine accessory drive layout details and testing methods and includes test configurations, pulley diameters, power loads, and guidance for interpreting test data. this information has been prepared from existing literature, including standards and data supplied by both producers and users of v-ribbed belts.
Automotive V-Ribbed Belt Drives and Test Methods
- ICS
- 43.040.50
- CCS
- T21
- 发布
- 1989-06-01
- 实施
- 1989-01-01
This preliminary standard contains specifications in addition to those given in DIN 74053 part 1. These additional specifications refer to the use with center axle trailers.
Mechanical connections betweeen towing vehicles and trailers; drawbar eye 50 with sleeve; additional specifications for applications on centre axle trailers
- ICS
- 43.040.70
- CCS
- T21
- 发布
- 1989-01
- 实施
This preliminary standard contains specifications in addition to those given in DIN 74052 part 1. These additional specifications refer to the use with center axle trailers.
Mechanical connections between towing vehicles and trailers; automatic bolt coupling 50; additional specifications for the use with centre axle trailers
- ICS
- 43.040.70
- CCS
- T21
- 发布
- 1989-01
- 实施
