T33 润滑件、密封件、联接件 标准查询与下载

QC/T 931-2013 强力软管夹箍

本标准规定了强力软管夹箍的型式与尺寸、技术条件。本标准适用于汽车发动机进排气系统用强力软管夹箍。

Heavy duty hose clamps

DB37/T 2264-2012 车用骨架密封圈压入、脱出力的测定

本标准适应于内包骨架、外露骨架及装配式骨架密封圈压入、脱出力的性能评价。

Determination of the press-in and pull-out force of the skeleton sealing ring for vehicles

BS ISO 7641:2012 道路车辆.高达3,5 t的拖车.钢制牵引杆的机械强度计算

Road vehicles. Trailers up to 3,5 t. Calculation of the mechanical strength of steel drawbars

SAE J2337/3-2012 流体动力和高压的连接,采用带有ISO 261螺纹及O形圈密封的端口,双头螺栓端及塞子.第3部分:端口塞堵要求,尺寸规格,设计和测试方法

The part of SAE J 2337 specifies dimensions, design, and performance requirements for eight plugs using a conical seal to insure leak proof performance with a design factor of 4 to 1. These connectors are intended for general and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These connectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuum to the working pressures shown in Table 1. Since many factors influence the pressure at which hydraulic systems will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to ensure that the required performance levels are met.

Connections for Fluid Power and High Pressure Use Ports, Stud Ends, and Plugs with ISO 261 Threads and O-Rings Sealing Part 3: Port Plug Requirements, Dimensions, Design, and Test Methods

SAE J1453-1-2012 O形面密封连接器的规格: 第1部分. 管路连接详情和通用性能和试验要求

The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 50 mm.

Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests

QC/T 883-2011 密封塞

本标准规定了密封塞的型式与尺寸、技术条件。 本标准适用于密封孔直径为4mm～20mm、密封压力不大于20MPa的汽车用密封塞。 本标准规定的密封塞适用于汽车的空气、液压系统。适用机体材料为铝合金、铸铁和钢。

Sealing plugs

SAE J2211-2011 抑制HFC-134a(R-134a)的建议使用程序

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. Refrigerant containment is an important part of servicing mobile air-conditioning (A/C) A/C systems. This procedure provides guidelines for technicians for servicing mobile A/C systems and operating refrigerant recycling equipment designed for HFC-134a (R-134a) (described in SAE J2210).

Recommended Service Procedure for the Containment of HFC-134a (R-134a)

SAE J1453-1-2011 O型环面密封连接器规范(R):第1部分.性能和试验中管道连接的详细信息和通用要求

1.1 PurposeThe three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal(ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tubediameters of 6 mm through 50 mm.1.2 Field of ApplicationThese connectors are intended for general application and hydraulic systems on industrial equipment and commercialproducts, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. Theseconnectors are capable of providing leak proof full flow connections in hydraulic systems operating from 95 kPa vacuumto the working pressures shown in Tables 1 and 2. Since many factors influence the pressure at which a hydraulicsystem will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For anyapplication, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer toensure that required performance levels are met.For use of these connectors in conditions outside the pressure and temperature limits specified, the manufacturers mustbe consulted.Both metric and inch tubing can be accommodated by changing only the sleeve to match the tube diameters. In the past,these connectors have been used predominantly with inch tubing. For new designs, the use of metric tubing should beconsidered.

(R) Specification for O-Ring Face Seal Connectors: Part 1.Tube Connection Details and Common Requirements for Performance and Tests

QC/T 696-2011 汽车底盘集中润滑供油系统

本标准规定了汽车底盘集中润滑供油系统的术语和定义、要求、试验方法、检验规则、标志、包装、运输、储存。 本标准适用于M、M、N、O类汽车底盘安装的、以电机作为动力源的集中润滑供油系统。

The centralized lubrication system of automotive chassis

SAE J2310-2011 矩形截面聚合物密封环

The purpose of this SAE Recommended Practice is to establish guidelines for the automatic transmission and hydraulic systems engineer to design rectangular cross section seals for rotating and static grooved shaft applications. Also included are material property comparisons of polymeric materials suitable for these applications. Historically, material covered in this document is not intended to include aluminum applications.

Rectangular Cross Section Polymeric Sealing Rings

SAE J1601-2011 液压启动汽缸用橡胶杯

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistance rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this specification.

Rubber Cups for Hydraulic Actuating Cylinders (Stabilized Type)

QC/T 666-2010 汽车空调（HFC-134a）用密封件 第1部分：Ｏ形橡胶密封圈

Seals for automotive air conditioners (HFC-134a) Part 1: O-ring rubber seals

BS ISO 1726-3:2010 道路车辆.牵引车和半拖挂车之间机械轴节.半拖挂车备用轮接触面积要求

Road vehicles. Mechanical couplings between tractors and semi-trailers. Requirements for semi-trailer contact area to fifth wheel

SAE J1298-2010 液压传动和一般用途的油泵联轴器诊断油口尺寸和位置用连接件

SAE J 1298 covers the recommended diagnostic port sizes for use in measuring hydraulic fluid temperature, pressure, flow, and for obtaining fluid samples. See SAE J 1502 for the detailed coupling specifications.

Connections for Fluid Power and General Use - Hydraulic Couplings - Diagnostic Port Sizes and Locations

SAE J515-2010 与液压连接器同时使用的O-形密封环材料规范

SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.

Specification for O-Ring Materials Used with Hydraulic Connectors

SANS 206:2009 道路车辆．使用非石油基液压制动液的液压制动盘式液压缸的弹性密封垫（最高工作温度120℃）

Specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc cylinders.

Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.)

SANS 205:2009 道路车辆．使用非石油基液压制动驱动缸的弹性皮碗和密封圈（最大工作温度70℃）

Specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles.

Road vehicles - Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 °C max.)

SAE J2495-2008 套管材料的热密封效率

This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves.

Thermal Containment Efficiency of Sleeve Materials

SAE J2224-2008 卡车、拖车和公共汽车车轮密封件及相关组件的鉴定

This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel sealsto identify their products.These symbols appear on seals and packaging.The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means ofidentifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

SAE J1603-2008 液压盘式制动器汽缸的橡胶密封件

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston. The specification contains the following major sections:a. Resistance to Fluid at Elevated Temperature—Physical Stability [loose parts in 120 °C ± 2 °C (248 °F ± 3.6 °F) brake fluid for 70 h]b. Resistance to Fluid at Elevated Temperature—Precipitation Characteristics [loose parts in 120 °C ± 2 °C (248 °F ± 3.6 °F) brake fluid for 70 h]c. Resistance to Elevated Temperatures in Dry Air [loose parts in 175 °C ± 2 °C (347 °F ± 3.6 °F) air for 22 h]d. Ambient Temperature Stroking Test [tested in brake assembly for 500 000 cycles to 7 MPa ± 0.3 MPa (1000 psi ± 50 psi)]e. High Temperature Stroking Test [tested in brake assembly for 70 h (70 000 strokes) at 120 °C ± 2 °C (248 °F ± 3.6 °F) to 7 MPa ± 0.3 MPa (1000 psi ± 50 psi)]f. Low Temperature Leakage Test [tested in brake assembly for 120 h at –40 to –43 °C (–40 to –45.4 °F)]g. Cycling Humidity Storage Corrosion Test [tested in brake assembly for 14 days at 95% humidity cycling between 21 to 46 °C (69.8 to 114.8 °F)]

Rubber Seals for Hydraulic Disc Brake Cylinders