T33 润滑件、密封件、联接件 标准查询与下载

SAE J1298-2008 液压发动机和通用液压联结器用连接件.诊断油口尺寸和位置

SAE J1298 covers the recommended diagnostic port sizes for use in measuring hydraulic fluid temperature, pressure, flow, and for obtaining fluid samples. See SAE J1502 for the detailed coupling specifications.

Connections for Fluid Power and General Use Hydrualic Couplings Diagnostic Port Sizes and Locations

SAE J1570-2008 液压盘式制动器活塞用橡胶灰尘防护罩

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation.The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used.The rubber material used in these boots is classified as suitable for operating in a temperature range of –40 to + 120 °C ±2 °C (–40 to + 248 °F ± 3.6 °F).

Rubber Dust Boots for the Hydraulic Disc Brake Piston

SAE J534-2008 润滑配件

This SAE Standard covers complete general and dimensional specifications for the various types of lubrication fittings and related threaded components intended for general application in the automotive and allied fields.

Lubrication Fittings

BS ISO 1726-2:2007 道路车辆.拖拉机和半挂车之间的机械连接.低耦合拖拉机和高容量半挂车之间的互换性

This part of ISO 1726 specifies dimensions to ensure interchangeability between a low coupling height tractor vehicle and a coupled high-volume semi-trailer, the two together constituting a high-volume articulated vehicle. It specifies certain interchangeability dimensions, including those of the optimised gooseneck contour, as well as operating dimensions related to angle values. The specifications are primarily intended to permit semi-trailers to be coupled with two-axle tractors. However, three-axle tractors are not excluded, provided they are in compliance with the requirements of this part of ISO 1726. This part of ISO 1726 does not provide limitations of maximum gross mass and overall dimensions, which are generally laid down by legislative requirements.

Road vehicles - Mechanical couplings between tractors and semi-trailers - Interchangeability between low-coupling tractors and high-volume semi-trailers

JASO D616-2007 汽车部件.线束连接器用试验方法和通用性能要求

Automotive parts-Test methods and general performance requirements for wiring harness connectors

ISO 6119:2006 道路车辆.使用非石油基液压制动液的液压盘式制动液压缸的弹性密封垫(最高工作温度120℃)

This International Standard specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section type seals (square, rectangular, “O”-ring), mounted stationary in the cylinder bore or on the movable piston of disc brakes.

Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.)

ISO 4928:2006 道路车辆.使用非石油基液压制动液的液压制动系统液压缸的弹性皮碗和密封圈(最高工作温度120℃)

This International Standard specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles; it does not include requirements relating to chemical composition, tensile strength and elongation of the rubber compound. Disc brake seals are not covered by this International Standard. This International Standard is applicable to moulded seals (cups or double-lipped type gland seals), 60 mm in diameter and smaller, compounded from high temperature-resistant rubber, for use in hydraulic actuating cylinders using road vehicle non-petroleum base hydraulic brake fluid conforming to the requirements of ISO 4925.

Road vehicles - Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (Service temperature 120 °C max.)

ISO 4930:2006 道路车辆.使用非石油基液压制动液的液压制动盘式液压缸的弹性密封垫(最高工作温度150℃)

This International Standard specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section type seals (square, rectangular, "0"-ring), mounted stationary in the cylinder bore or on the movable piston of disc brakes.

Road vehicles - Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 150° C max.)

ISO 6118:2006 道路车辆.使用非石油基制动液的液压制动促动缸的弹性皮碗和密封圈(最高工作温度70℃)

This International Standard specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles. It does not include requirements relating to chemical composition, tensile strength and elongation of the rubber compound. Disc brake seals are not covered by this International Standard. This International Standard is applicable to moulded seals (cups or double-lipped type gland seals), 60 mm in diameter and smaller, compounded from rubber, for use in hydraulic actuating cylinders employing road vehicle non-petroleum base hydraulic brake fluid conforming to the requirements of ISO 4925. NOTE The rubber used in these seals shall be suitable for operation in a temperature range of —40 °C to +70 °C.

Road vehicles - Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 °C max.)

KS R ISO 7633:2005 道路车辆.使用石油基液压制动液的鼓式液压制动轮缸弹性保护罩(最高工作温度120℃)

이 규격은 광유계 액압 브레이크액을 사용하는 드럼식 휠 브레이크 실린더의 끝부에 부착되는

Road vehicles-Elastomeric boots for drum type hydraulic brake wheel cylinders using a petroleum base hydraulic brake fluid(service temperature 120℃ maximum)

KS R ISO 7631:2005 道路车辆.使用石油基液压制动液的液压制动系统液压缸弹性皮碗和密封垫圈(最高工作温度120℃)

이 규격은 광유계 액압 브레이크액을 사용하는 도로 차량의 액압 브레이크 시스템에 사용하는

Road vehicles-Elastomeric cups and seals for cylinders for hydraulic braking systems using a petroleum base hydraulic brake fluid(service temperature 120℃ max.)

BS EN 14420-6:2004 带夹具的软管配件.第6部分:TW油槽车联接器

This document specifies the design, materials and dimensions for hose fittings with couplings for tank trucks (TW couplings). Couplings for tank trucks in accordance to this document are intended to link hoses with connections for the transport of liquids, solid matters and gases with the exception of liquid gas and steam. They can be employed in a working pressure range of ? 0,8 bar up to 16 bar at working temperatures of ? 20 °C up to + 65 °C. Couplings for tank trucks for other operating conditions are subject to agreement. WARNING Male and female dust couplings are pressure resistant plugs. They do not work as locking device, so, if pipelines remain under pressure, a locking device shall be superposed.

Hose fittings with clamp units - Part 6: TW tank truck couplings

VC 8080-2005 使用非石油基刹车液的机动车动力气缸用替换弹性皮碗和密封圈（服务温度70到150 °C）

Specifies the requirements for cups and seals, whether in loose form or assembled in parts, operating in hydraulic brake fluid for all motor vehicles. This specification applies to moulded brake cups and seals for use in non-petroleum base brake fluid as

Replacement elastomeric cups and seals for hydraulic brake actuating cylinders for use in motor vehicles using non-petroleum base hydraulic brake fluid (service temperature 70 °C to 150 °C max)

QC/T 641-2005 汽车用塑料密封条

本标准规定了汽车用塑料密封条的技术要求、试验方法、检验规则及标志、包装运输和贮存。 本标准适用于聚氯乙烯塑料密封条(以下简称密封条)。

Plastic weatherstrips for automobile

ISO 11406:2001/cor 1:2005 商用道路车辆.带尾部连接器的牵引车辆和牵引杆式挂车间的机械连接.互换性.技术勘误1

This is Technical Corrigendum 1 to ISO 11406-2001 (Commercial road vehicles — Mechanical coupling between towing vehicles with rear-mounted coupling and drawbar trailers — Interchangeability)

Commercial road vehicles - Mechanical coupling between towing vehicles with rear-mounted coupling and drawbar trailers - Interchangeability; Technical Corrigendum 1

QC/T 716-2004 汽车密封条插入力和拔出力试验方法

本标准规定了汽车用密封条插入力和拔出力的试验方法。 　　本标准适用于汽车用密封条插入力和拔出力的试验。

Retention strength and insertion resistance test method for automobile weatherstrips

SAE J2638-2003 13,608/kg(3,000/lb)以下拖车GVW的备用轮和鹅颈管附件的性能

This document establishes minimum performance criteria and definition of terms for the towing interface between a towing vehicle and fifth wheel or gooseneck trailer at or below 13 608 kg (30 000 lb) gross trailer weight. This establishes criteria for the hitch, tow vehicle attachment structure, trailer attachment structure, and coupling. This document is intended as a guide for manufacturers of fifth wheel and/or gooseneck trailers at or below 13 608 kg (30 000 lb) gross trailer weight and of tow vehicles and of components necessary to tow these trailers. Regulatory authorities desiring to formulate regulations may use this standard as a guide. This document is also intended for voluntary use by others associated with manufacturing of these products.

Fifth Wheel and Gooseneck Attachment Performance Up to 13 608/kg (30 000/lb) Trailer GVW

JIS D 2609 ERRATUM 1:2003 JIS D2609 勘误表 1

ERRATUM

SANS 20055:2003 关于批准汽车机械联结件的统一规定

Lays down the requirements which mechanical coupling devices and components shall meet in order to be regarded internationally as being mutually compatible.

Uniform provisions concerning the approval of mechanical coupling components of combinations of vehicles

JIS D 2609:2002 道路车辆.使用非石油基液压制动液的液压盘式制动缸的弹性密封件

この規格は，自動車用液圧ディスクブレーキシリンダで非鉱油系ブレーキ液を使用するデイスクブレーキシリンダのゴムシール(以下，シールという。)について規定する。

Road vehicles -- Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid