T35 车用电子、电气设备与仪表综合 标准查询与下载

ASTM D3306-14 汽车及轻型设备用乙二醇基发动机冷却剂的标准规范

1.1 This specification covers the requirements for ethylene glycol or propylene glycol base engine coolants used in automobiles or other light duty service cooling systems. When concentrates are used at 40 to 708201;% concentration by volume in water, or when prediluted glycol base engine coolants 50 volume % or higher engine coolant concentrate are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion. 1.2 The coolants governed by this specification are categorized as follows: Coolant Type Description     I Ethylene glycol base concentrate II Propylene glycol base concentrate V Ethylene glycol base concentrate containing glycerin     III Ethylene glycol predilute 50 volume % or higher engine coolant concentrate IV Propylene glycol predilute 50 volume % or higher engine coolant concentrate VI Ethylene glycol base predilute containing glycerin 50 volume % or higher engine coolant concentrate Note 1—This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. This specification shall also apply to engine coolants prepared using glycol generated from recycled or reprocessed used coolant or reprocessed industrial-source glycol, provided that said glycol meets the requirements of Specification E1177. Separate specifications (D6471 and D6472) exist for engine coolants prepared from recycled or reprocessed used coolant or reprocessed industrial-source glycol that does not meet the requirements established in Specification E1177. This specification shall also apply to glycol based engine coolants prepared using fully refined glycerin provided that said glycerin meets the requirements for Specification D7640. 1.3 The values stated in SI units are to be regarded as the ......

Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service

KS R ISO 3538:2013 道路车辆.安全玻璃窗材料.光学性能试验方法

이 표준은 도로 차량에 사용하는 유리 또는 그 밖의 재료로 구성된 모든 안전 유리 재료의 안전 요건에 관련된 광학적 시험방법에 대하여 규정한다.

Road vehicles — Safety glazing materials — Test methods for optical properties

KS R ISO 3536:2013 道路车辆.安全玻璃窗材料.词汇

이 표준은 도로 차량에 사용하는 안전 유리 재료에 관련된 용어를 정의한다.

Road vehicles — Safety glazing materials — Vocabulary

QC/T 951-2013 汽车用电路断电器

本标准规定了汽车用片式直热型电路断电器(以下简称断电器)的术语和定义、要求、试验方法、检验规则等。本标准适用于M、N、L类车用自动复位式及手动复位式电路断电器。其他道路车辆可参照使用。

Circuit-breakers for automobile

KS R ISO 4107:2013 商用车辆.轮毂附件的尺寸

이 표준은 스터드 구멍이 6개, 8개 또는 10개인 차량의 허브에 상용차용 휠을 부착할 때 필요한 치수를 규정하고 있다.이 표준은 향후 장비로 추천된 중앙 보어(central bore)를 중심으로 하는 평면 부착 형식을 고려하고있다. 다른 형식들이 현재 사용되고 있다.이 사양은 차량 간 휠이 호환될 수 있음을 나타내는 것은 아니다.

Commercial vehicles – Wheel hub attachment dimensions

KS R ISO 3911:2013 充气轮胎用车轮及轮圈.词汇、标识和标志

이 표준은 공기 타이어에 사용되는 휠과 림의 용어, 명칭 및 표기법에 대하여 규정하고 있다. 정의와이와 함께 수반되는 그림들은 모든 휠 디자인 특징의 포괄적인 도표화를 제공하기보다는 근본적인휠과 림의 용어와 정의를 목적으로 하고 있다. 이 표준은 또한 휠과 림에 대해 전 세계적으로 동일한 식별 기준을 확립하기 위해 표기의 내용, 위치 및 최소 크기를 규정하고 있다.

Wheels and rims for pneumatic tyres – Vocabulary, designation and marking

KS R ISO 3779:2013 道路车辆.车辆识别号码(VIN).内容和构成

이 표준은 도로 차량에 대한 전 세계적으로 동일한 식별 기준을 확립하기 위해 차량 식별 번호(VIN)의 내용과 구조를 정의하고 있다.이 표준은 KS R ISO 3833에 정의된 모터 차량, 트레일러, 모터사이클 및 모터 자전거에 적용된다.

Road vehicles-Vehicle identification number(VIN)-Content and structure

KS R ISO 3832:2013 轿车.后备箱基准体积检测方法

이 표준은 승용차 화물실의 기준 체적을 측정하는 방법에 대하여 규정한다.

Passenger cars-Luggage compartments-Method of measuring reference volume

DB11/Z 993.2-2013 电动汽车远程服务与管理系统技术规范 第2部分：车载终端

本指导性技术文件规定了电动汽车远程服务与管理车载终端的功能要求、性能要求、试验方法、检验规则、标志标识以及运输存储安装要求。本指导性技术文件适用于电动汽车车辆运行和停车充电两种工况下对车辆与动力蓄电池进行服务与管理的装置。

Electric Vehicle Remote Service and Management System Technical Specification Part 2: Vehicle Terminal

QC/T 29032-2013 汽车用空气滤清器堵塞报警传感器

本标准规定了汽车用空气滤清器堵塞报警传感器(以下简称传感器)的要求、试验方法、检验规则和标志、包装、储存、保管。本标准适用于汽车用空气滤清器堵塞报警器、传感器和带有报警功能的传感器。其他机动车用空气滤清器堵塞报警传感器也可参照执行。传感器与压力表、指示或报警装置配套工作,用于指示汽车空气滤清器堵塞状况。

Alarms sensor for automobile air filters

DIN EN 61982:2013 电动道路车辆推进用蓄电池(非锂).性能和耐久试验(IEC 61982-2012).德文版本EN 61982-2012

Secondary batteries (except lithium) for the propulsion of electric road vehicles - Performance and endurance tests (IEC 61982:2012); German version EN 61982:2012

SAE J1587-2013 重型车辆用微型计算机设备之间的电子数据交换

This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice defines a document for the format of messages and data that is of general value to modules on the data communications link. Included are field descriptions, size, scale, internal data representation, and position within a message. This document also describes guidelines for the frequency of and circumstances in which messages are transmitted. In order to promote compatibility among all aspects

Electronic Data Interchange Between Microcomputer Systems in Heavy-Duty Vehicle Applications

ANSI/UL 458-2013 地面车辆和船舶用功率变换器/变频器和功率变换器/变频器系统

Power Converters/Inverters and Power Converter/Inverter Systems for Land Vehicles and Marine Crafts

NF S56-202-1:2012 休闲旅居车辆.12 V直流超低压电器装置.第1部分:旅居挂车

Leisure accommodation vehicles - 12 V direct current extra low voltage electrical installations - Part 1 : caravans.

SAE J1455-2012 在重型车辆应用的电子设备设计推荐性环保操作规程

The scope of this recommended practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment and agricultural equipment including implements. This document is intended to aid the designer of commercial vehicle electronic systems and components by providing guidelines that may be used to develop environmental design goals. Specific test requirements are to be agreed upon by the customer and supplier.

Recommended Environmental Practices for Electronic Equipment Design in Heavy-Duty Vehicle Appllications

SAE J2847-2-2012 可拆卸车辆和外接DC装料机之间的通讯

This SAE Recommended Practice SAE J2847-2 establishes requirements and specifications for communication between PLUG-IN ELECTRIC VEHICLE (EVCC)s and the DC Off-board charger. Where relevant, this document notes, but does not formally specify, interactions between the vehicle and vehicle operator. This document applies to the off-board DC charger for conductive charging, which supplies DC current to the vehicle RESS of the electric vehicle through a SAE J1772 Hybrid coupler. Communications will be on the J1772 Pilot line for PLC communication. The details of PLC communications are found in SAE J2931-4. The specification supports DC energy transfer via Forward Power Flow (FPF) from source-to-vehicle.

Communication Between Plug-In Vehicles and Off-Board DC Chargers

SAE J1067-2012 七芯导线电缆卡车和总线

This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8-1/10-5/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications.

Seven Conductor Cable Truck and Bus

DB35/T 1207-2011 车载音视频设备技术要求和试验方法

本标准规定了车载音视频设备的术语和定义、技术要求、性能要求、试验方法等。 本标准适用于安装在各类汽车设计规定位置内的车载音视频设备，包括带或不带小尺寸（< 1 0 . 2 英寸）机载T F T液晶显示器两种型式，是产品设计、生产定型和质量检验的依据。

Technical requirements and test methods for vehicle-mounted audio and video equipment

QC/T 897-2011 电动汽车用电池管理系统技术条件

本标准规定了电动汽车用电池管理系统的术语与定义、要求、试验方法、检验规则、标志等。 本标准适用于电动汽车用动力电池管理系统。

Technical specification of battery management system for electric vehicles

QC/T 895-2011 电动汽车用传导式车载充电机

本标准规定了电动汽车传导式车载充电机的基本构成、参数、功能、要求、试验方法、包装、储运方法及标志与标识。 本标准适用于纯电动汽车及可外接充电的混合动力电动汽车用的车载充电机。

On-board conductive charger for electric vehicles