U20 舾装设备综合 标准查询与下载

CSA Z275.4-02-2002 潜水作业资格标准 第2版 更新 第1号 更新 No 2

This Standard specifies minimum requirements for a supplier’s quality assurance program-Category 1. The supplier is responsible for planning and developing a program which assures that each management, design, and technical responsibility for quality is

Standard of Competence for Diving Operations, second edition; Update #1: November 2003; Update #2: August 2004

SC/T 8068-2001 渔船玻璃钢舾装件

Ship equipment of fiberglass reinforced plastics for fishing vessel

SC/T 8119-2001 玻璃钢渔船舾装件安装技术要求

本标准规定了舫装件在玻璃俐渔船上安装所需预埋件的基本结构型式、连接方法和技术要求。 本标准适用于玻璃钢渔船。

Technical demand of install outfit for fiberglass reinforced plastics fishing vessel

ASTM F1323-01 船用焚烧装置标准规范

1.1 This specification covers the design, manufacture, performance, operation, functioning, and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during the ship''s normal service (that is, maintenance, operational, domestic, and cargo-associated wastes). 1.2 This specification is a companion document to Guide F1322. 1.3 This specification applies to those incinerator plants with capacities up to 1500 kW per unit.1.4 Additional information is given in Appendix X1 - Appendix X9. 1.5 This specification does not apply to systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, etc. 1.6 This specification does not address the electrical supply to the unit, nor the foundation connections and stack connections. 1.7 This specification does not cover emissions requirements. 1.8 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. If an incinerator is to be operated in littoral regions, the strictest governing regulations for those countries in which the incinerator may operate would form the requirement basis. See 5.11.

Standard Specification for Shipboard Incinerators

DIN 85389:1998 船舶和海洋技术.超轻型的活动法兰和对焊法兰.DN 32至DN 50,PN25以下,DN 65至DN 125,PN 10以下.设计原则

The document specifies extra light flanges for castings.

Ships and marine technology - Flanges on castings extra light duty - DN 32 to DN 50, PN up to 25, DN 65 to DN 125, PN up to 10 - Principles of design

DIN 85387-2:1998 船舶和海上技术.超轻型的活动法兰和对焊法兰.第2部分:CuNi10Fe1,6Mn 材料制的 DN 32至DN 50,PN25以下,DN 65至DN 125,PN 10以下对焊法兰.

These welding necks are used together with loose flanges according to DIN 85387-1 in pipelines on light and fast ships.

Ships and marine technology - Loose flanges and welding necks extra light duty - Part 2: Welding necks made of CuNi10Fe1,6Mn, DN 32 to DN 50, PN up to 25, DN 65 to DN 125, PN up to 10

DIN 85387-1:1998 船舶和海上技术.超轻型的活动法兰和对焊法兰.第1部分:DN 32至DN 50,PN25以下,DN 65至DN 125,PN 10以下的活动法兰

These loose flanges are used together with welding necks according to DIN 85387-2 in pipelines on light and fast ships.

Ships and marine technology - Loose flanges and welding necks extra light duty - Part 1: Loose flanges DN 32 to DN 50, PN up to 25, DN 65 to DN 125, PN up to 10

ANSI/ASTM F1309:1998 船用机械基座固定楔安装程序惯例

This practice covers the acceptable methods of fitting chocks to marine machinery foundations. The values stated in SI units shall be regarded as standard. The values in parentheses are for information only. This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

ASTM F1323-98 船用焚烧装置标准规范

1.1 This specification covers the design, manufacture, performance, operation, functioning, and testing of incinerators intended to incinerate garbage and other shipboard wastes generated during the ship''s normal service (that is, maintenance, operational, domestic, and cargo-associated wastes). 1.2 This specification is a companion document to Guide F1322. 1.3 This specification applies to those incinerator plants with capacities up to 1500 kW per unit.1.4 Additional information is given in Appendix X1 - Appendix X9. 1.5 This specification does not apply to systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, etc. 1.6 This specification does not address the electrical supply to the unit, nor the foundation connections and stack connections. 1.7 This specification does not cover emissions requirements. 1.8 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. If an incinerator is to be operated in littoral regions, the strictest governing regulations for those countries in which the incinerator may operate would form the requirement basis. See 5.11.

Standard Specification for Shipboard Incinerators

ANSI/ASTM F956:1997 铸制声音信号铃规范

This specification covers cast sound-signalling bells, together with bulkhead mounting plates for the smaller bells, for use on ships, boats, and other marine craft, for compliance with the rules in the convention on the International Regulations for Preventing Collisions at Sea (commonly called Colregs). See Appendix X1. Bells and bulkhead mounting plate shall be sized as indicated in Section 4 (see Appendix X2). For consistency with International Regulations, all measurements are in SI units.

Specification for Bell, Cast, Sound Signaling

ANSI/ASTM F957:1997 声音信号钟规范

This specification covers gongs for use on ships 100 m or more in length, as required by International Regulations (see Appendix X1). For consistency with International Regulations, all measurements are in SI units.

Specification for Gong, Sound Signaling

CSA Z275.4-97-1997 潜水作业资格标准.通用指令第1-2号

L'Association canadienne de normalisation (BA), sous les auspices de laquelle cette Norme nationale a été préparée, a re?u ses lettres patentes en 191 9 et son accréditaüon au sein du S y s t h de normes nationales par le Conseil canadien des normes en 1

Norme De Competence Pour Les Operations De Plongee Fiche No. 1-2

ANSI/ASTM F986:1997 吸滤器外壳规范

This specification covers the design, materials, and construction of strainer boxes for use in ships' bilges and other such tank locations that require trash protection for suction pipes and pumps. This specification covers pipe sizes from NPS 11/2 through NPS 16 (see Note 1). Note 1 -The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as "nominal diameter, " "size, " and "nominal size." The values stated in inch-pound units are to be regarded as the standard.

Specification for Suction Strainer Boxes

ARMY MIL-M-55670 A NOTICE 1-1996 AB-621()/G桅杆

ML-M-35670A is inactive ?ur new design and is no longer used except for rcpbment purposes.

MAST AB-621()/G

NAVY A-A-50604-1993 夹式耐火不折边有袖伸缩接头

The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-E-15330 which is canceled in part.

EXPANSION JOINT, SLEEVED, (NON-FLANGED), FIRE-RETARDANT, WITH RETAINING CLAMPS

NAVY MIL-D-16791 G (1)-1993 清洁剂一般用途(液体非离子物质)

This amendment forms a part MoIfL -D-16791G dated 26 January 1990, and is approved for use by all Departments and Ageonfc itehse Department of Defense.

DETERGENTS, GENERAL PURPOSE (LIQUID, NONIONIC)

CSA Z275.2-92-CAN/CSA-1992 潜水人员的安全规定.通用指令第1号

Regles De Securite Pour Les Travailleurs En Plongee Fiche No 1

Safety Regulation for Diving Personnel.General Instruction No1

ANSI/ASTM F956:1991 铸铃规格,声音信号

Specification for Bell, Cast, Sound Signaling

ANSI/ASTM F957:1991 铃碗的规范,声音信号

Specification for Gong, Sound Signaling

ASTM F1322-90(2004) 船上焚烧装置的选择

1.1 This guide covers selection criteria to assist procurers in selecting the appropriate incinerator for their needs.1.2 This guide is a companion document to Specification F 1323.1.3 This guide does not apply to incinerator systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, and so forth.

Standard Guide for Selection of Shipboard Incinerators