U20 舾装设备综合 标准查询与下载

ANSI/ASTM F1322:1990 船用焚烧装置选用指南

This guide covers selection criteria to assist procurers in selecting the appropriate incinerator for their needs.This guide is a companion document to Specification F 1323. This guide does not apply to incinerator systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, and so forth.

Guide for Selection of Shipboard Incinerators

ASTM F1322-90(2009) 船用焚烧装置的标准指南

1.1 This guide covers selection criteria to assist procurers in selecting the appropriate incinerator for their needs. 1.2 This guide is a companion document to Specification F1323. 1.3 This guide does not apply to incinerator systems on special incinerator ships, for example, for burning industrial wastes such as chemicals, manufacturing residues, and so forth.

Standard Guide for Selection of Shipboard Incinerators

JIS F 3414:1989 船用单桅钩

この規格は，船のデリックプームのトッピングリフトを固縛するのに用いるホーンクリート(以下，ホーンクリートという。)について規定する。

Ships' horn cleats

NAVY MIL-D-3716 B INT AMD 1-1988 动态除湿气活性干燥剂

This interim amendment is approved for use within the Department of the Air Force, with MIL-D-3716B dated 28 September 1987.

DESICCANTS, ACTIVATED FOR DYNAMIC DEHUMIDIFICATION

NAVY MIL-D-3716 B-1987 动态除湿气活性干燥剂

This specification covers desiccants that remove qoisture from air , other gases, and from 1iquids by dynamic means and that offer an approximate indication of the relative humidity of an enclosed space.

DESICCANTS, ACTIVATED FOR DYNAMIC DEHUMIDIFICATION

NAVY DOD-B-24673-1986 船及小手工铃铛

This specification covers bells for use aboard ship and small craft.

BELLS, SHIPS AND SMALL CRAFT

ASTM F986-86(2004) 吸滤器外壳

1.1 This specification covers the design, materials, and construction of strainer boxes for use in ships'' bilges and other such tank locations that require trash protection for suction pipes and pumps. 1.2 This specification covers pipe sizes from NPS 1frac12; through NPS 16 (see Note 1). Note 18212;The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as "nominal diameter," "size," and "nominal size." 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Suction Strainer Boxes

ASTM F986-86(1997) 吸滤器外壳规范

1.1 This specification covers the design, materials, and construction of strainer boxes for use in ships'' bilges and other such tank locations that require trash protection for suction pipes and pumps. 1.2 This specification covers pipe sizes from NPS 11/2 through NPS 16 (see Note). Note-The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as "nominal diameter," "size," and "nominal size." 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Suction Strainer Boxes

ASTM F986-86(2008) 吸滤器外壳的标准规范

1.1 This specification covers the design, materials, and construction of strainer boxes for use in ships'' bilges and other such tank locations that require trash protection for suction pipes and pumps. 1.2 This specification covers pipe sizes from NPS 1½ through NPS 16 (see Note 1). Note 18212;The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Suction Strainer Boxes

CB* 471-1985 艇底塞

本标准规定的艇底塞用于各种救生艇、交通艇、工作艇、巡逻艇和小型游艇等。

Bottom plug

NF J39-020:1985 造船工业.滚装船和陆地的连接.直线形船尾/船首连接坡道的船与终点港间的连接装置

Shipbuilding. Roll on/roll off ship-to-shore connection. Interface between terminals and ships with straight stern/bow ramps.

ISO 6043:1985 造船及海上结构物 受拉伸作用的眼板叉头 主要尺寸

Lays down the main dimensions for interchangeability and the materials for eyes, forks and associated bolts or pins for components subject to tension load. Is not applicable to components subject to compressive thrust or torsional loads.

Shipbuilding and marine structures; Eye and fork assemblies under tension load; Main dimensions

CB 3104-1981 船舶综合放样符号

Ship comprehensive stakeout symbol

JIS F 7451:1978 海运伞形齿轮

Marine bevel gears

JIS F 7452:1978 船舶用通用接头

この規格は，船の水密すベり戸，天窓，通風弁，諸管系弁，かじ取り，主機回転計などの開閉装置又は伝動装置に用いる船用自在継手について規定する。

Marine universal joints

JIS F 7453:1978 船舶用传动轴接头

この規格は，船の水密すべり戸，天窓，通風弁，諸管系弁，かじ取り，主機回転計などの開閉装置又は伝動装置に用いる船用伝動軸継手について規定する。

Marine transmission shaft joints

JIS F 7454:1978 船舶用传动轴活动接头

この規格は，船の水密すべり戸，天窓，通風弁，諸管系弁，かじ取り，主機回転計などの開閉装置又は伝動装置に用いる船用伝動軸伸縮継手について規定する。

Marine transmission shaft loose joints

JIS F 7455:1978 船舶用传动轴轴承

この規格は，船の水密すべり戸，天窓，通風弁，諸管系弁，かじ取り，主機回転計などの開閉装置又は伝動装置に用いる伝動軸軸受について規定する。

Marine transmission shaft bearings

ARMY MIL-M-55670 A-1972 AB-621()/G桅杆

This specification covers the requirements for a quick erectable, 50 foot

MAST AB-621()/G

ISO/R 784:1968 船舶卫生系统安装图常用符号

The symbols given in tables have been classified in the following manner: - General conventional signs, - Pipes and pipe joints, - Valves and supply fittings. The general conventional signs concern symbols representing principal parts.

Conventional signs to be used in schemes for the installations of sanitary systems in ships