共找到 453 条与 甲板机械 相关的标准,共 31 页
MIL-D-52462A(ME) remains inactive for new design, however, the document is valid for acthewhen needed.
DRIVER, DECK PIN
This document is intended for unification of cable lifters and at the same time to ensure their functioning by laying down minimum requirements and clue values for the main dimensions.
Windlasses and anchor capstans - Cable lifters for anchor chains - Design dimensions
MIL-I-60476A, dated 6 September 1990, is inactive for new design and is no longer used, except for replacement purposes.
IGNITER, MARK 125 MOD 5, LOADING ASSEMBLING AND PACKING
MIL-C-22226A, dated 22 February 1973,is inactive for new design and is no longer used, except for replacement purposes.
COPPER NICKEL MANGANESE ALLOY BARS, PLATES, AND SHEETS, LOW MAGNETIC EFFECT (FOR SPECIAL PURPOSE TOOLS AND EQUIPMENT)
Specification of control equipment for marine A.C. electric cargo winch
Pedestal fairleads (old man fairleads)
本标准规定了绞缆筒的型式、额定负载、尺寸与技术要求、试验方法和检验规则等。 本标准适用于船舶甲板机械,作系泊带缆、移船、起重、拖曳、绞收渔网等作业的绞缆筒的设计、生产与验收。
Warping end
This notice should be filed in fi-ont of MIL-R-40080C(ME), dated 21 May 1975.
RAMP, LOADING, VEHICLE: PORTABLE, FOUR-SECTION, 12,000-POUND CAPACITY
This notice should be filed in fiont of MIL-R-52899B(ME), dated 8 July 1986.
RAMP: LOADING VEHICLE
The purpose of this standard is to provide a general methodology for the test equipment, procedures, targets, and terminology needed to develop ballistic performance evaluation and ranking of advanced armor materials against high density eroding projectiles.
BALLISTIC PERFORMANCE RANKING OF CERAMIC ARMOR PLATES AGAINST HIGH DENSITY PENETRATORS
This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.
DECK COVERING, LATEX CONCRETE
This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.
DECK COVERING MATERIALS
本标准规定了液压舵机的出厂试验方法和型式试验方法。 本标准适用于各类液压舵机整机产品的试验。
Test method of hydraulic steering gears
This specification covers materials requirements for control rolled, quenched and tempered high strength wrought steel armor plate for lightweight armor applications up to and including 1/22 inches in thickness(see 6.2).
ARMOR PLATE, CONTROL ROLLED, STEEL, WROUGHT, HIGH STRENGTH, HIGH QUALITY
The elastomer insert mounts are used for elastic mounting of pipes, devices and components equipment. They can be used mounts fastening clamps type B to DIN 86025-1 and type D to DIN 86025-2.#,,#
Fastening clamps with bracket - Part 3: Insert
The fastening clamps with bracket to this standard are used for mounting of pipes outside diameters of 108 mm up to 610 mm. This clamps with elastomer insert can be used within an environmental temperature range from -20 ?to 120 ?
Fastening clamps with bracket - Part 2: Type C without insert, type D with insert
The fastening clamps with bracket are used for mounting of pipes outside diameters of 57 mm up to 89 mm. This clamps with elastomer insert can be used within an environmental temperature range from -20 ?to 120 ?
Fastening clamps with bracket - Part 1: Type A without insert, type B with insert
The document specifies pedestal fair leads, that are applied on sea-going- and inland vessels as part of the mooring equipment.#,,#
Pedestal fair leads
1. This standard is approved for use by all Departments and Agencies of the Department of Defense(DoD).
V50 BALLISTIC TEST FOR ARMOR
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号