U44 船用内燃机 标准查询与下载

GB/T 2497-1993 船用柴油机增压空气冷却器

本标准规定了船用柴油机增压空气冷却器（简称空冷器）的分类、技术要求、试验方法、检验规则和标志包装等。 本标准适用于各种类型船用柴油机空冷器；也可适用于其他用途的柴油机空冷器。

Charge air coolers for marine diesel engines

GB/T 14363-1993 柴油机机油消耗测定方法

本标准规定了柴油机在台架试验时，机油消耗（包括机油消耗量和机油消耗率）的测定方法。以下简称《测定方法》。 本标准适用于大中小型柴油机，根据具体情况选用其中一种方法进行测定。

Measurement of lubricant oil consumption for diesel engines

GB 11873-1989 船用柴油机清洁度测定方法

Method of determination of cleanliness for marine diesel engines

GB 11872-1989 船用柴油机清洁度限值

Limit of cleanliness for marine diesel engines

GB 11871-1989 船用柴油机辐射的空气噪声限值

本标准规定了船用柴油机在台架试验时辐射空气噪声的A声功率级的限值。 本标准适用于船用柴油机。

Limits of airborne noise emitted by marine diesel engines

GB/T 6301-1986 船用柴油机燃油消耗率测定方法

本标准适用于船用柴油机台架试验时燃油消耗率的测定。

Determination of fuel consumption rate for marine diesel engine

GB/T 6302-1986 船用柴油机热工参数的测量

本标准适用于船用柴油机运转时，油、水、气的压力、温度、流量和消耗量的测量。

Measurement of thermodynamics parameters for marine diesel engine

GB/T 5741-2008(英文版) 船用柴油机排气烟度测量方法

Measure method for exhaust smoke of marine diesel engine

DIN EN ISO 8469:2021 小艇. 非耐火燃料软管(ISO 8469-2021); 德文版本EN ISO 8469-2021

This document specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter

Small craft - Non-fire-resistant fuel hoses (ISO 8469:2021); German version EN ISO 8469:2021

T/CECS 718-2020 柴油机消防泵组技术规程

主要技术内容包括：总则、术语、系统设计与组成、安装与调试、竣工验收、维护管理等。

Technical specifications for fire pump set driven by diesel engine

CB/T 3259-2017 船用柴油机曲轴箱油雾探测器

Marine Diesel Engine Crankcase Oil Mist Detector

CB/T 4466-2017 船用全自动反冲洗油滤器

Marine automatic backwash oil filter

CB/T 4441-2016 船用柴油机电子调速器

Marine diesel engine electronic governor

CB/T 4440-2016 船用柴油机气阀弹簧

Marine Diesel Engine Valve Spring

CB/T 4439-2016 船用柴油机进、排气阀

Marine diesel engine intake and exhaust valves

CB/T 4438-2016 船用柴油机气缸盖螺栓、贯穿螺栓和主轴承螺栓

Cylinder head bolts, through bolts and main bearing bolts for marine diesel engines

ISO 13363:2016 船用发动机排湿系统用橡胶和塑料软管.规范

This International Standard specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water). It does not apply to outboard motor/personal water craft. The three types are the following: — type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement; — type 2: a hardwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement with a helical wire embedded in it; — type 3: a hose or tube (flexible connector), made of oil-resistant material, with or without a reinforcement or cover, intended for use in short lengths in locations where the connector is protected from mechanical damage. The two classes are the following: — class A: intended for diesel engines; — class B: intended for petrol engines and for diesel engines with a very high exhaust temperature.

Rubber and plastics hoses for marine-engine wet-exhaust systems - Specification

CB/T 3254.1-2013 船用柴油机台架试验 第1部分:标准基准状况及功率燃油消耗和机油消耗的标定

本部分规定了船用柴油机(以下简称柴油机)台架试验的标准基准状况,功率、燃油消耗和机油消耗的标定方法,以及非标准环境状况下功率与燃油消耗的修正方法。本部分适用于船用主柴油机(以下简称主机)和辅柴油机(以下简称辅机)。

Marine diesel engine bench test.Part 1: Standard reference condition and declaration of power, fuel and lubricating oil consumptions

CB/T 3452-2013 船用柴油机高压油管总成

本标准规定了船用柴油机高压油管总成(以下简称高压油管总成)的产品分类、要求、试验方法、检验规则、标志、包装、运输和储存等的要求。本标准适用于气缸直径不小于200 mm的船用柴油机的高压油管总成。

High pressure fuel oil pipe complete of marine diesel engine

CB/T 3254.2-2013 船用柴油机台架试验 第2部分:试验方法

本标准规定了船用柴油机(以下简称柴油机)台架试验的试验条件、试验要求、试验项目。本标准适用于船用主柴油机和辅柴油机。

Marine diesel engine bench test.Part2: Test methods