V06 环境条件 标准查询与下载

SAE ARP5583A-2010 航空器在高辐射场环境(HIRF)下的认证介绍

This guide provides detailed information, guidance, and methods related to the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and European Aviation Safety Agency (EASA) draft Advisory Material Joint (AMJ), both titled "The Certification of Aircraft Electrical and Electronic Systems for Operation in the High-Intensity Radiated Fields (HIRF) Environment". The AC provides acceptable means, but not the only means, of compliance with Title 14, Code of Federal Regulations (14 CFR) 23.1308, 25.1317, 27.1317, and 29.1317, High-Intensity Radiated Fields (HIRF) protection for Aircraft Electrical and Electronic Systems, and applicable FAA HIRF Special Conditions to prevent hazards to aircraft electrical and electronic systems due to HIRF produced by external transmitters. It is also intended for this guide to provide the same information, guidance, and methods to the European Aviation Safety Agency (EASA) interim HIRF policies certification requirements. This guide is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. The information in this guide represents a collection of best engineering practices that have been used to certify aircraft HIRF protection. An applicant may elect to establish an alternative method of compliance that is acceptable to the cognizant airworthiness authorities. This document is consistent with the guidance in FAA AC 20-158. The AC 20-158 and draft HIRF AMJ may be referenced in aircraft certification requirements such as JAA/EASA certification review items. While this document is generally consistent with AC 20-158 and draft HIRF AMJ, users of this document should verify that the guidance in this document is acceptable to the cognizant airworthiness authorities.

Guide to Certification of Aircraft in a High-Intensity Radiated Field (HIRF) Environment

KS W ISO 2669:2007 航空器设备的环境试验.稳态加速度

이 규격은 두 가지 형태의 정상상태 가속 시험을 설명하고 있으며, 민간항공기가 운항 중에

Environmental tests for aircraft equipment-Steady-state acceleration

DLA MS90707 REV B ADMIN NOTICE 5-2007 外部手柄扣环

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

RING, RETAINING, EXTERNAL GRIP

DLA MS3215 REV B NOTICE 5-2007 外部扣环

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

RING, RETAINING, EXTERNAL,"E," REINFORCED (REDUCED SECTION TYPE)

DLA MS3217 REV B NOTICE 4-2007 (戴锥形部分型)重型外部扣环

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

RING, RETAINING, EXTERNAL, HEAVY-DUTY (TAPERED SECTION TYPE)

DLA MS16632 REV B NOTICE 3-2007 (戴锥形部分型)重型外部扣环

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http://assist.daps.dla.mil/.

RING, RETAINING, EXTERNAL, CRESCENT (REDUCED SECTION TYPE)

ISO 21348:2007 航天环境(天然的和人造的).太阳辐照度的测定规程

This International Standard specifies the process for determining solar irradiances and is applicable to measurement sets, reference spectra, empirical models, theoretical models, and solar irradiance proxies or indices that provide solar irradiance products representing parts or all of the solar electromagnetic spectrum. Its purpose is to create a standard method for specifying all solar irradiances for use by space systems and materials users.

Space environment (natural and artificial) - Process for determining solar irradiances

GJB 5601-2006 中国参考大气（地面~80km）

本标准规定了中国地面～8Okm高度内的参考大气。 本标准适用于航空器、航天器及运载工具和导弹等武器装备的设计和试验，军事气象保障以及相关科学研究工作亦可参考使用。

China reference atmosphere (ground～80km)

NAVY A-A-59382 A-2006 循环使用环境保护袖子

This Commercial Item Description (CID) covers two kit types of black, tubular, continuous, doublewall,reusable sleeves, in a minimum of 13 sizes, to provide corrosion and environmental protection for electrical and electronic connections in shipboard applications where connectors are expected to be frequently accessed.

REUSABLE ENVIRONMENTAL PROTECTION SLEEVES

ARMY MIL-DTL-32201-2006 HMMWV型12X8英寸(名义)外部安装后视镜装配

This document covers exterior-mounted, automotive rearview mirror assemblies, without hardware or bracketry required to mount the mirror assembly to the US Army HMMWV, Armored Security Vehicle(ASV), and other type vehicles.

MIRROR ASSEMBLIES, REARVIEW, HMMWV STYLE, 12X8 INCH (NOMINAL), EXTERIOR MOUNTING

NAVY QPL-AS83519-2-2006 耐环境热缩性焊接式屏蔽终端

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense. All products listed herein have been qualified under the requirements for the product as specified in the latest adopted issue of the applicable non-Government standard. This list is subject to change without notice; revision or amendment of this list will be issued as necessary. The listing of a product does not release the manufacturer from compliance with the non-Government standard requirements.

SHIELD TERMINATION, SOLDER STYLE, INSULATED, HEAT-SHRINKABLE, ENVIRONMENT RESISTANT, GENERAL SPECIFICATION FOR

DLA DSCC-DWG-05013-2006 外部贴装,TTL与CMOS兼容,3.3伏特,312KHZ至170兆赫,可三态晶体控制振荡器

This drawing describes the requirements of a enable/tri-state, miniature, surface mount crystal controlled oscillator with a frequency range of 312 kilohertz (kHZ) to 170 megahertz (MHz), TTL and CMOS compatible, rated at 3.3 volts, meeting the requirements of MIL-PRF-55310 product level B, type 1, class 2 supplied to the requirements of this drawing specified herein.

OSCILLATOR, CRYSTAL CONTROLLED, 3.3 VOLT, ENABLE/TRI-STATE, 312KHZ TO 170 MHZ, TTL AND CMOS COMPATIBLE, SURFACE MOUNT

DLA DSCC-DWG-05014-2006 外部贴装能兼容TTL和CMOS的,312千赫至120兆赫的,三态5伏晶振

This drawing describes the requirements of a enable/tri-state, miniature, surface mount crystal controlled oscillator with a frequency range of 312 kilohertz (kHZ) to 120 megahertz (MHz), TTL and CMOS compatible, rated at 5 volts, meeting the requirements of MIL-PRF-55310 product level B, type 1, class 2 supplied to the requirements of this drawing specified herein.

OSCILLATOR, CRYSTAL CONTROLLED, 5 VOLT, ENABLE/TRI-STATE, 312KHZ TO 120 MHZ, TTL AND CMOS COMPATIBLE, SURFACE MOUNT

DLA QPL-87819-10-2006 耳机麦克风(听力防护型,高和温和的环境噪声水平)一般规格

This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-PRF-87819. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

HEADSET-MICROPHONE (HEARING PROTECTIVE TYPE, HIGH AND MODERATE AMBIENT NOISE LEVELS), GENERAL SPECIFICATION FOR

AIAA S-120-2006 航天系统 质量性能控制

Mass Properties Control for Space Systems

Mass Properties Control for Space Systems

DLA A-A-59266 VALID NOTICE 1-2005 中央型外部圆柱形通用砂轮机 [代替:DLA MIL-G-23823 E CANC 通用 1,DLA MIL-G-23823 E,DLA MIL-G-23823 D,DLA MIL-G-23823 C,DLA MIL-G-23823 B,DLA MIL-G-23823 A,DLA MIL-G-23823]

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

GRINDING MACHINE, UNIVERSAL, CYLINDRICAL, EXTERNAL, CENTER-TYPE [Superseded: DLA MIL-G-23823 E CANC NOTICE 1, DLA MIL-G-23823 E, DLA MIL-G-23823 D, DLA MIL-G-23823 C, DLA MIL-G-23823 B, DLA MIL-G-23823 A, DLA MIL-G-23823]

DLA A-A-59332 VALID NOTICE 1-2005 电脑数字控制(CNC)中央型外部圆柱形砂轮机 [代替:DLA MIL-G-80278 CANC 通告 1,DLA MIL-G-80278]

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

GRINDING MACHINE, CYLINDRICAL, EXTERNAL, CENTER-TYPE, COMPUTER NUMERICAL CONTROL (CNC) [Superseded: DLA MIL-G-80278 CANC NOTICE 1, DLA MIL-G-80278]

ARINC 440-2005 训练设备数据供应和支撑指南

GUIDELINES FOR THE PROVISIONING AND SUPPORT OF TRAINING EQUIPMENT DATA

GUIDELINES FOR THE PROVISIONING AND SUPPORT OF TRAINING EQUIPMENT DATA

DLA MS90708 REV C (1)-2003 [由以下代替: 美国机械工程师协会 B18.24.3, 美国机械工程师协会 B18.24.3]外部联锁保留环

This amendment forms a part of MS90708C, dated 28 June 1995,and is approved for use by all Departments and Agencies of the Department of Defense.

RING, RETAINING, EXTERNAL INTERLOCKING [Superseded By: ASME B18.24.3, ASME B18.24.3]

DLA MS16627 REV B REINST NOTICE 2-2003 (圆锥截面类型)外部转换护环[参考:ASME B18.24.3, ASME B18.24.3]

(Copies of the referenced federal and military specifications, standards, and handbooks are available from the Department of Defense Single Stock Point, Defense Printing Service Detachment Office, Building 4-D,700 Robbins Avenue, Philadelphia, PA 19111-5094.)

RING, RETAINING, INTERNAL, INVERTED (TAPERED SECTION TYPE) [Refer To: ASME B18.24.3, ASME B18.24.3]