W10 棉纺织综合 标准查询与下载

DB41/T 955-2014 絮用纤维制品 热熔被、褥

Hot-melt quilts and mattresses for wadding fiber products

DIN EN ISO 10306:2014 纺织品.棉纤维.成熟度的气流法评定(ISO 10306-2014).德文版本EN ISO 10306-2014

Textiles - Cotton fibres - Evaluation of maturity by the air flow method (ISO 10306:2014); German version EN ISO 10306:2014

BS ISO 18068:2014 棉纤维. 糖含量的试验方法. 分光光度法

Cotton fibres. Test method for sugar content. Spectrophotometry

ISO 10306:2014 纺织品 棉纤维 成熟度的气流法评定

This International Standard specifies a method for the evaluation of the maturity of loose randomized cotton fibres by measuring the resistance to air flow of a plug of cotton fibres under two prescribed conditions. The method is applicable to cotton taken at random from bales. Laps and slivers or other sources of lint cotton may be tested, however results may differ if fibres are taken from bales.

Textiles - Cotton fibres - Evaluation of maturity by the air flow method

FZ/T 60040-2013 水溶性粘合衬水洗后分离性能试验方法

Test method for separation performance of water-soluble adhesive interlining after washing

FZ/T 60040-2014 水溶性粘合衬水洗后分离性能试验方法

本标准规定了水溶性粘合衬与面料粘合的组合试样,经水洗后分离性能的试验方法。本标准适用于以各种材质的机织物为基布的水溶性粘合衬水洗后分离时间的测定。各种材质的针织物和非织造布为基布的水溶性粘合衬可参照执行。

Testing method for separating performance of adhesive-bonded woven interlinings with hydrosoluble binder after washing

BS ISO 2403:2014 纺织品. 棉纤维. 马克隆尼值的测定

Textiles. Cotton fibres. Determination of micronaire value

SAE AMS3806F-2013 80磅力(356 N)裂断强度丝光棉飞机用织物

This specification covers one strength and one weave of mercerized cotton cloth known as ""airplane cloth."" This cloth has been used typically for covering aircraft surfaces, such as wings, fuselage, ailerons, elevators, and other airfoil surfaces, but usage is not limited to such applications.

Cloth, Airplane, Mercerized Cotton, 80 Pounds Force (356 N) Breaking Strength

FZ/T 07001-2013 棉纺织行业综合能耗计算导则

本标准规定了棉纺织企业在生产过程中,单位产量、单位增加值及单位产值综合能耗的定义、计算边界和计算方法。本标准适用于棉纺织企业的耗能管理和行业内能效对标。

Calculation directives for comprehensive energy consumption of cotton spinning and weaving industries

FZ/T 10021-2013 色纺纱线检验规则

本标准规定了色纺纱线的验收、检验项目和试验方法、抽样方法、检验评定及复验。本标准适用于贸易双方或受委托的检验机构对纯纺、混纺色纺筒子纱线品质的验收和复验。

Inspection rules for colour yarn

FZ/T 10022-2013 纺织上浆用浆料的化学需氧量/五日生化需氧量的检测试验方法

本标准规定了纺织上浆用浆料的化学需氧量(COD)/五日生化需氧量(BOD)测定的方法。本标准适用于纺织上浆用浆料的化学需氧量(COD)/五日生化需氧量(BOD)的测定。本标准对被检测浆料制成的试样,其化学需氧量(COD)测定下限为15 mg/L,测定上限为1 000 mg/L,其氯离子浓度不应大于1 000 mg/L;对于化学需氧量(COD)大于1 000 mg/L或氯离子含量大于1 000 mg/L的试样,可经适当稀释后进行测定。本标准对被检测浆料制成的试样,其生化需氧量(BOD)的测量范围是2 mg/L~6 000 mg/L;对于生化需氧量(BOD)大于6 000 mg/L的试样,可经适当稀释后进行测定。

Test method for determination of chemical oxygen demand/biochemical oxygen demand after 5 days of the sizes used in textile warp sizing

KS K 0312-2012 棉纤维长度试验法:直排法

이 표준은 면 섬유의 섬유장과 섬유장의 분포 측정방법에 대하여 규정한다.

Test method for length and length distribution of cotton fibers：Array method

KS K 7506-2012 滑翔伞服装

이 표준은 패러글라이딩으로 낙하할 때 착용하는 남성 및 여성용 패러글라이딩복에 대하여 적용

Paragliding wear

KS K 7803-2012 工作服

이 표준은 작업복에 대하여 규정한다.

Working wear

KS K 6101-2012 棉毛巾

이 표준은 면 타월에 대하여 규정한다.

Cotton towel

DB41/T 738-2012 学生公寓配套用纺织品

Textiles for student apartments

DB41/T 739-2012 学生公寓用絮制品

Wool products for student apartments

ASTM D1441-12 试验用棉纤维取样的标准操作规程

The reliability of the results of any test method depends primarily upon how well the specimens tested represent the original source material or lot. Failure to provide a test specimen which accurately represents the lot from which it is drawn will produce misleading test results regardless of the accuracy and precision of the test method.1.1 This practice covers procedures for taking a lot sample of cotton fibers, from a designated source (lot), and reducing the lot sample through a series of steps to produce test specimens that are representative of the source and suitable for the determination of fiber properties according to established procedures. 1.2 This practice has been used extensively for commercial acceptance testing of cotton fibers as well as for arbitration testing and research. Note 18212;This practice is used in taking samples of cotton for testing by Test Methods D1440, D1442, D1445, D1447, D1448, D1464, , D2812, D5866 and D5867. 1.3 The procedures do not cover the selection of samples for the determination of moisture. Special handling and protection of the sample from the prevailing atmosphere required for samples taken for the determination of moisture are not provided for in this practice. See Test Method D2495. 1.4 The values stated in SI units are to be regarded as standard. No other units of measure are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Sampling Cotton Fibers for Testing

ASTM D1445/D1445M-12 棉纤维的断裂强度和延伸率的标准试验方法(扁纤维束法)

This test method is considered satisfactory for acceptance testing when the levels of the laboratories are controlled by the use of the same reference standard cotton samples because the current estimates of between-laboratory precision are acceptable under these conditions. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. This test method is useful in research studies to determine the influence of variety, environment, and processing on fiber strength and elongation; and in studies of the relationships between these fiber properties, processing performance, and quality of end-product. Values obtained for flat bundle tenacity and elongation show a high correlation with values measured on single fibers and require much less time and skill. Studies have shown that strength measurements obtained with different types of instruments are highly correlated, but the results are on different levels. By use of correction factors calculated from tests made on standard calibration samples of known or established test values, the results obtained with different types of instruments at a specified gauge length can be adjusted to comparable levels. Due to the normal variation in cottons, strength test results for one gauge length cannot be reliably estimated from tests made at a different gauge length. The terms tensile strength and breaking tenacity are sometimes used interchangeably. They are relational but are not equivalent (see 12.1.1 and 12.1.2). Tenacity is commonly expressed as centinewtons per tex (cN/tex), grams-force per denier (gf/den) or pounds-force per denier (lbf/den). Tenacity in centinewtons/tex is numerically equal to tenacity in grams-force/tex times 0.981.1.1 This test method covers the determination of (1) the tensile strength or breaking tenacity of cotton fibers as a flat bundle using a nominal zero gauge length, or (2) the tensile strength or breaking tenacity and the elongation at the breaking load of cotton fibers as a flat bundle with 1/8-in. [3.2-mm] clamp spacing. This test method is applicable to loose ginned cotton fibers of untreated cottons whether taken before processing or obtained from a textile product. 1.2 This test method is designed primarily for use with special fiber bundle clamps and special strength testing instruments but may be used with other tensile strength and elongation testing machines when equipped with appropriate adapters to accommodate the fiber clamps. Note 18212;Other methods for measuring the breaking tenacity of fiber bundles include Test Method D1294, Test for Breaking Strength of Wool Fiber Bundles1 in gauge Length; and D5867, Test Method for Measurement of Physical Properties of Cotton Fibers by High Volume Instruments. 1.3 The values stated in either SI units or inch-pound units are to be r......

Standard Test Method for Breaking Strength and Elongation of Cotton Fibers (Flat Bundle Method)

ASTM D1464-12 棉花染色差异性的标准操作规程

This practice is not recommended for acceptance testing because the information obtained is qualitative rather than quantitative in nature. The response of fibers to the dye mixture is indicative of the uniformity of dyeing, the probability of dyeing defects due to neps, and the difficulties to be expected from heterogeneity of fibers that differ in dyeing characteristics. In general, the red dye is retained predominantly by the thick-walled fibers and the green by the thin-walled fibers. The color response of the specimens to the dyes in the binary mixture reflects the behavior to be expected with many other dyes. The colors from red to green may be influenced by factors such as weather during the growing period, exposure of open bolls in the field before harvest, natural color, fineness, and degree of wall development.1.1 This practice covers a test for the characterization of certain dyeing behavior of cotton. This practice is especially applicable to raw cotton fibers, but may also be adapted to cotton yarns and fabrics. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Differential Dyeing Behavior of Cotton