SAE AMS 2431/3D-2007
洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR)

Peening Media (AWCR) Conditioned Carbon Steel Cut Wire Shot, Regular Hardness (45 to 52 HRC)

洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR) 是非强制性国家标准，您可以免费下载前三页

SAE AMS 2431/3D-2007 发布历史

The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Conditioned carbon steel cut wire shot, regular hardness, conforming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stresscorrosion cracking. Generally, regular hardness conditioned carbon steel cut wire shot is used on parts of hardness less than 50 HRC.

SAE AMS 2431/3D-2007由美国机动车工程师协会 US-SAE 发布于 2007-05-01。

SAE AMS 2431/3D-2007 在中国标准分类中归属于: V90 航空器与航天器制造用设备综合，在国际标准分类中归属于: 49.040 有关航空航天制造用镀涂和有关工艺。

SAE AMS 2431/3D-2007 发布之时，引用了标准

SAE J 441-1993 钢丝切丸
SAE J 444-2005 喷砂和清洁用铸造喷丸和粗砂粒度的规范
SAE J 827-2005 高碳铸钢喷丸
SAE J 1173-1988 喷丸处理用玻璃珠的尺寸分类和特性
SAE J 1830-1987 喷丸处理用陶瓷丸的尺寸分类和特性

SAE AMS 2431/3D-2007的历代版本如下：

2007年05月01日 SAE AMS 2431/3D-2007 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR)

SAE AMS 2431/3D-2007 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR) 由 SAE AMS 2431/3C-2006 变更而来。

标准号: SAE AMS 2431/3D-2007
发布日期: 2007年05月01日
实施日期
废止日期: 无
中国标准分类号: V90
国际标准分类号: 49.040
发布单位: US-SAE
引用标准: ASTM B 214-2007 ASTM C 169-1992 ASTM E 11-2004 ASTM E 18-2005 ASTM E 18-2007 ASTM E 140-2007 ASTM E 350-1995 ASTM E 353-1993 ASTM E 384-2006 ASTM E 384-2007 SAE J 441-1993 SAE J 444-2005 SAE J 445-2005 SAE J 827-2005 SAE J 1173-1988 SAE J 1830-1987 SAE AM
被代替标准: SAE AMS 2431/3C-2006

适用范围: The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS 2431. Conditioned carbon steel cut wire shot, regular hardness, conforming to this specification is intended for use in peening metal surfaces to impart compressive stresses to these surfaces thereby increasing resistance to fatigue and stresscorrosion cracking. Generally, regular hardness conditioned carbon steel cut wire shot is used on parts of hardness less than 50 HRC.

SAE AMS 2431/3D-2007系列标准

SAE AMS 2431/1C-2002 SAE AMS 2431/1D-2007 洛氏硬度(45～52 HRC)射丸冲压铸钢(ASR) SAE AMS 2431/1E-2010 一般硬度的喷丸介质(ASR)铸钢丸(45-52 HRC) SAE AMS 2431/2C-2002 SAE AMS 2431/2D-2007 高硬度(55～62 HRC)的喷丸硬化介质(ASH)铸钢丸 SAE AMS 2431/2E-2010 高硬度喷丸介质(ASH)铸钢丸(55至62 HRC) SAE AMS 2431/3B-1996 SAE AMS 2431/3C-2006 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备 SAE AMS 2431/3D-2007 洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR) SAE AMS 2431/4A-1996 SAE AMS 2431/4B-2006 调节不锈钢切割线射丸的冲压设备 SAE AMS 2431/4C-2007 适合喷丸硬化介质(AWS)的不锈钢丝切丸 SAE AMS 2431/5-1988 喷丸介质.表面硬化钢喷丸 SAE AMS 2431/5A-2006 表面硬化钢冲压球冲压设备 SAE AMS 2431/5B-2011 表面硬化钢喷丸的介质 SAE AMS 2431/6A-1998 SAE AMS 2431/6B-2005 玻璃喷丸介质 SAE AMS 2431/6C-2007 玻璃珠冲压设备 SAE AMS 2431/7-1988 陶瓷喷丸介质 SAE AMS 2431/7A-2006 陶瓷喷射冲压设备 SAE AMS 2431/7B-2013 陶瓷射击锤击介质 SAE AMS 2431/8-1996 SAE AMS 2431/8A-2006 高硬度调节碳钢切割线射丸的冲压设备 SAE AMS 2431/8B-2007 适合高硬度(55～62 HRC)喷丸硬化介质(AWCH)的碳钢切割线射丸 SAE AMS 2431/9-2020 SAE AMS 2431A-1996 喷丸介质一般要求 SAE AMS 2431B-2006 冲压设备.一般要求 SAE AMS 2431C-2010 冲压介质.一般要求

SAE AMS 2431/3D-2007 中可能用到的仪器设备

紫外分析仪/紫外检测仪/紫外透射仪

SAE AMS 2431/3D-2007洛氏硬度(45～52 HRC)调节碳钢切割线射丸冲压设备(AWCR)