17.060 体积、质量、密度和粘度的测量 标准查询与下载

ISO/DIS 8655-10 活塞式体积测定仪 第10部分：用户指南和对能力、培训和 POVA 适用性的要求

Piston-operated volumetric apparatus — Part 10: User guidance and requirements for competence, training, and POVA suitability

ISO/TR 16153:2023 活塞式容积测定设备.使用光度法测量容积的不确定度的测定

Determination of uncertainty for volume measurements of a piston-operated volumetric apparatus using a photometric method

ISO/TR 20461:2023 用重量法对测量的不准确度的测定

Determination of uncertainty for volume measurements of a piston-operated volumetric apparatus using a gravimetric method

ASTM B873-23 测试方法B212、B329和B417中使用的表观密度杯体积测量的标准试验方法

1.1 This test method covers a procedure for measuring the volume of the apparent density cups used in Test Methods B212, B329, and B417. 1.2 The apparent density cup, particularly its rim, may become worn during use, and it is recommended that the volume of the cup be checked periodically (at least every 6 months) in order to ensure that it complies with the specified volume. 1.3 Units—With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm3 ) and gram (g) units is the long standing industry practice, the values in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Volume of Apparent Density Cup Used in Test Methods B212, B329, and B417

ASTM D7394-18(2023) 使用三台旋转台式粘度计测定建筑涂料流变特性的标准实施规程

1.1 This practice describes a popular industry protocol for the rheological characterization of waterborne architectural coatings using three commonly used rotational bench viscometers. Each viscometer operates in a different shear rate regime for determination of coating viscosity at low shear rate, mid shear rate, and at high shear rate respectively as defined herein. General guidelines are provided for predicting some coating performance properties from the viscosity measurements made. With appropriate correlations and subsequent modification of the performance guidelines, this practice has potential for characterization of other types of aqueous and non-aqueous coatings. 1.2 The values in common viscosity units (Krebs Units, KU and Poise, P) are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Rheological Characterization of Architectural Coatings using Three Rotational Bench Viscometers

ASTM E2975-23 同心圆筒旋转粘度计校准或校准验证的标准试验方法

1.1 This test method describes the calibration or calibration verification of rotational viscometers in which the rotational element is immersed in a Newtonian reference material under ambient temperature conditions. The method is applicable to rotational-type viscometers where a constant rotational speed results in a measured torque generated by the test specimen, and to Stormer viscometers where a constant applied torque results in a measured rotational speed. It is not intended for cone-and-plate or parallel plate viscometers. 1.2 Calibration shall be performed with Newtonian reference materials using experimental conditions such as temperature, viscosity range, and shear rate (rotational speed), as close as practical to those to be used for measurement of test specimens. 1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions that are provided for information only and are not considered standard. 1.3.1 Common viscosity units of Poise (P) are related to the SI units by the equivalency 1 cP = 1 mPa·s. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers

ASTM E2977-15(2023) 液体样品傅里叶变换核磁共振（FT-NMR）光谱仪性能测量和报告的标准实施规程

1.1 This practice covers procedures for measuring and reporting the performance of Fourier-transform nuclear magnetic resonance spectrometers (FT-NMRs) using liquid samples. 1.2 This practice is not directly applicable to FT-NMR spectrometers outfitted to measure gaseous, anisotropically structured liquid, semi-solid, or solid samples; those set up to work with flowing sample streams; or those used to make hyperpolarization measurements. 1.3 This practice was expressly developed for FT-NMR spectrometers operating with proton resonance frequencies between 200 MHz and 1200 MHz. 1.4 This practice is not directly applicable to continuous wave (scanning) NMR spectrometers. 1.5 This practice is not directly applicable to instruments using single-sideband detection. 1.6 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Measuring and Reporting Performance of Fourier-Transform Nuclear Magnetic Resonance (FT-NMR) Spectrometers for Liquid Samples

KS B 5298-2022 家用个人称重仪表

Personal weighing instruments for domestic use

T/SKZB 004-2022 黄酒灌装体积净含量管理和控制规范

本文件规定了黄酒灌装体积净含量的基本要求、试验方法、结果验证等基本内容。

specification for management and control of net content of yellow rice wine filling volume

KS L ISO 3819:2022 实验室玻璃器皿.烧杯

Laboratory glassware — Beakers

KS L ISO 3819-2022 实验室玻璃器皿.烧杯

Laboratory glassware — Beakers

ASTM D5478-13(2022) 用落针粘度计测定材料粘度的标准试验方法

1.1 These test methods cover the measurement of the viscosity of Newtonian and non-Newtonian liquids. These test methods are applicable to liquids having viscosities in the range from 5 × 10−4 Pa·s to 103 Pa·s (0.5 cP to 106 cP). The shear rate range is dependent upon the needle used and viscosity of the liquid and may vary from 10−4 s−1 to 103 s−1 . With an extension bar and applied weight, a shear rate of 104 s–1 may be achieved. 1.2 The yield stress of liquids having this property may also be determined. 1.3 These test methods consist of determining liquid viscosities of Newtonian and non-Newtonian fluids (clear or opaque) by measuring the steady-state (constant) or terminal velocities of cylindrical needles as they fall through the test liquid under the influence of gravity. Yield stresses of nonNewtonian liquids may be measured using the same procedure. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer

ASTM D8092-22 用微通道粘度计现场测定运动粘度的标准试验方法

1.1 This test method describes a means for measuring the kinematic viscosity of transparent and opaque liquids such as new and in-service lubricating oils using a miniature microchannel viscometer at 40 °C in the range of 12.9 mm2 /s to 174 mm2 /s 1.2 The precision has only been determined for those materials and viscosity ranges, as indicated in Section 17 on Precision and Bias. 1.3 This test method is specifically tailored to obtaining a rapid, direct, temperaturestabilized measure of the kinematic viscosity of new and in-service lubricants in the field in realtime without the use of solvents or chemical cleaning agents. The measurement takes place at 40 °C and kinematic viscosity is directly obtained. No temperature extrapolations or density corrections are necessary. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 9 on Hazards. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer

ASTM D7961-22 在大温度和压力范围内校准U形管密度传感器的标准实施规程

1.1 This practice outlines procedures for the calibration of U-tube density cells. It is applicable to instruments capable of determining fluid density at temperatures in the range –10 °C to 200 °C and pressures from just greater than the saturation pressure to 140 MPa. The practice refers to density cells as they are utilized to make measurements of fluids primarily in the compressed-liquid state. Examples of substances for which the density can be determined with a calibrated U-tube density meter include: crude oils, gasoline and gasoline-oxygenate blends, diesel and jet fuels, hydraulic fluids, and lubricating oils. 1.2 This practice specifies a procedure for the determination of the expanded uncertainty of the density measurement. 1.3 This practice pertains to fluids with viscosities < 1 Pa·s (1000 centipoise) at ambient conditions. 1.4 4 The values listed in SI units are regarded as the standard, unless otherwise stated. The SI unit for mass density is kilograms per cubic metre (kg·m-3 ) and can be given as grams per cubic centimetre (g·cm-3 ). 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Calibrating U-tube Density Cells over Large Ranges of Temperature and Pressure

GSO OIML R 129-1:2022 多维测量仪器 第1部分：计量技术要求

This Standard specifies the metrological and technical requirements for the type evaluation of multi-dimensional measuring instruments used to determine the dimensions and/or dimensional volume of an object for the purpose of calculating charges for postage, freight or storage. The instruments may be used in conjunction with a weighing instrument also used in the determination of charges, in which case the procedure is usually for the dimensional volume to be calculated, a conversion factor applied, and the resulting dimensional weight of the object compared to its weight to establish which quantity (the largest of measured weight or dimensional weight) will be used to determine the charges. In some cases dimensions other than volume are used for determining charges. The Recommendation also includes type evaluation procedures, verification procedures and test procedures. The requirements of This Standard apply to automatic and semi-automatic instruments, but they do not apply (for example) to simple linear measures such as tape measures. The instruments measure the length, width and height of a rectangular box and in some cases determine the dimensional volume of that box. If the object is not in the form of a rectangular box, the volume of the smallest rectangular box (by volume) which fully encloses the object is determined (see 2.2.1). Instruments may include different measurement devices, each using a different method to measure separate dimensions of an object. The instrument may measure the object whilst there is relative motion between the instrument and the object. If the multi-dimensional measuring instrument is associated with a weighing instrument, which is also used for determining the charges, the requirements for the weighing instrument are found in the following OIML Recommendations: (a) OIML R 76 Non-automatic weighing instruments [1] for non-automatic weighing instruments; and (b) OIML R 51 Automatic catchweighing instruments [2] for automatic weighing instruments. The requirements of This Standard may also be used, where applicable, for type evaluation and verification of other instruments which measure the dimensions and/or the volume of objects for applications other than for determining postage, freight or storage charges.

Multi-dimensional measuring instruments - Part 1: Metrological and technical requirements

GSO OIML R 129-4:2022 多维测量仪器 第4部分：型式评价报告格式

This “Type evaluation report format”, the subject of OIML R 129-4, aims at presenting, in a standardized format, the results of the evaluation to which a type of a multi-dimensional measuring instrument shall be submitted with a view to its approval.

Multi-dimensional measuring instruments Part 4: Type evaluation report format

GSO OIML R 129-3:2022 多维测量仪器 第3部分：测试报告格式

The “Test report format”, the subject of OIML R 129-3, aims at presenting, in a standardised format, the results of the various tests and examinations to which a type of a multi-dimensional measuring instrument (MDMI) shall be submitted with a view to its approval.

Multi-dimensional measuring instruments Part 3: Test report format

BS EN ISO 8655-6:2022 活塞操作容量装置 用于确定体积的重量参考测量程序

1   Scope This document specifies a gravimetric reference measurement procedure for the determination of volume of piston-operated volumetric apparatus (POVA). The procedure is applicable to complete systems comprising the basic apparatus and all parts selected for use with the apparatus, disposable or reusable, involved in the measurement by delivery (Ex) or contained (In).

Piston-operated volumetric apparatus - Gravimetric reference measurement procedure for the determination of volume

T/JMJLXH 001-2022 液化石油气充装操作规程（YSP35.5液化石油气钢瓶）

本规定了液化石油气气瓶（以下简称气瓶）充装、的基本原则和安全技术要求。并适用于YSP35.5液化石油气钢瓶的充装、贮存、运输。

Liquefied Petroleum Gas Filling Operation Procedures (YSP35.5 Liquefied Petroleum Gas Cylinders)

T/JMJLXH 002-2022 液化石油气充装操作规程（YSP118液化石油气钢瓶）

规定了液化石油气气瓶（以下简称气瓶）充装、的基本原则和安全技术要求。并适用于YSP118液化石油气钢瓶的充装、贮存、运输。

Liquefied Petroleum Gas Filling Operation Procedures (YSP118 Liquefied Petroleum Gas Cylinders)