23.060 阀门 标准查询与下载

JB/T 1754-2008 阀门零部件 接头组件

本标准规定了接头、接头垫、接头螺母的结构形式、尺寸、材料和要求。 本标准适用于锻钢阀门。

Components of valves.Connections

JB/T 1757-2008 阀门零部件 卡套 卡套螺母

本标准规定了卡套、卡套螺母的结构形式、尺寸和技术要求。 本标准适用于公称压力不大于 PN40，公称尺寸 DN6～DN25 的锻钢阀门用卡套和卡套螺母。

Components of valves.Sockets and guide and nuts

JB/T 2769-2008 阀门零部件.高压螺纹法兰

本标准规定了法兰连接锻造角式高压阀门用透镜垫密封螺纹法兰形式、尺寸、技术要求等。 本标准适用于公称压力PN160～PN320、公称尺寸DN3～DN200的螺纹法兰。

Components of valves.High pressure threaded flanges

JB/T 5208-2008 阀门零部件.隔环

本标准规定了阀门填料函用隔环的形式、尺寸和要求。 本标准适用于公称压力不小于PN16、公称尺寸不小于DN50铸钢闸阀填料函用隔环。

Components of valves.Lantern rings

JB/T 5211-2008 阀门零部件.闸阀阀座

本标准规定了闸阀阀座的结构形式、尺寸和技术要求。 本标准适用于钢制闸阀。

Components of valves.Seats of gate valves

QB/T 2909-2007 温度压力安全保护阀

本标准规定了用于封闭承压式热水器（系统）的温度压力安全保护阀的定义、命名与结构、技术要求、试验方法、检验规则及标志、包装、运输、贮存、使用说明书。 本标准适用于连续运行温度不超过85℃、紧急状态下温度不超过99℃，工作压力不超过1400kPa、泄荷流道直径为DN15~DN50的各种温度压力安全保护阀。

Temperature/pressure protection valves

KS B ISO 9461-2007(2012) 液压传动－阀口、子板、控制装置和螺线管的识别

Hydraulic fluid power－Identification of valve ports,subplates, control devices and solenoids

AIR FORCE QPL-25675-22-2007 飞机和导弹液压检查缩图阀门

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defens

VALVES, CHECK MINIATURE, HYDRAULIC, AIRCRAFT AND MISSILE

KS B 2821-2007 低温阀门的性能试验方法

? ??? -50~-196 ℃ ???? ???? ??? ??? ?? ?? ??? ????

Method for performance testing of low temperature valves

KS B 2821-2007(2017) 对低温阀门的性能试验方法

Method for performance testing of low temperature valves

KS B 2821-2007(2022) 低温阀门性能试验方法

Method for performance testing of low temperature valves

AIR FORCE MIL-HDBK-344 A VALID NOTICE 1-2007 电子设备制造(电子开关)环境应力筛选

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.da

ENVIRONMENTAL STRESS SCREENING (ESS) OF ELECTRONIC EQUIPMENT

AIR FORCE MIL-PRF-25675 C NOTICE 1-2007 航行器和导弹水力微型检查阀

This notice should be file in front of MIL-PRF-25675C Amendment 1 dated 12 Sept 2002. MIL-PRF-25675C is inactive for new design and is no longer used, except for replacement purposes.

VALVES, CHECK, MINIATURE, HYDRAULIC, AIRCRAFT AND MISSILE

DLA MIL-DTL-83739 C (1)-2007 一般规格射频固态天线开关

This specification covers the general requirements for solid-state antenna switches for use at radio frequencies

SWITCHES, ANTENNA, RADIO FREQUENCY, SOLID-STATE, GENERAL SPECIFICATION FOR

NAVY MIL-PRF-32150 A-2007 表面和舰艇静态自动总线汇流开关(SABT)

This specification covers the Static Automatic Bus Transfer Switch (SABT), herein referred to as the SABT (see 6.4.23) or the unit, for use on surface and submarine naval vessels. Requirements for Automatic Bus Transfer Switches (ABTs) and Manual Bus Transfer Switches (MBTs) are not covered in this specification. MILPRF-17773 specifies the requirements for ABTs and MBTs.

STATIC AUTOMATIC BUS TRANSFER SWITCH (SABT) ON SURFACE AND SUBMARINE NAVAL VESSELS

AIR FORCE MIL-PRF-25370 F VALID NOTICE 1-2007 充气阀(救生设备)

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.da

VALVE, PNEUMATIC INFLATOR (LIFE PRESERVER, MA-1)

NAVY QPL-5594-12 NOTICE 1-2007 密封型自保持扭子开关一般规定

QPL-5594-12, which identified products qualified under the requirements specified in MIL-S-5594, has been transformed to an equivalent qualification data set (QDS).

SWITCHES, TOGGLE, ELECTRICALLY HELD SEALED, GENERAL SPECIFICATION FOR

DLA SMD-5962-95813 REV E-2007 反射变硬互补金属氧化物半导体双重单刀双掷开关硅单片电路线型微电路

This drawing documents three product assurance class levels consisting of high reliability (device classes Q andM), space application (device class V) and for appropriate satellite and similar applications (device class T). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. For device class T, the user is encouraged to review the manufacturer’s Quality Management (QM) plan as part of their evaluation of these parts and their acceptability in the intended application.

MICROCIRCUIT, LINEAR RADIATION HARDENED CMOS, DUAL SPDT ANALOG SWITCHES, MONOLITHIC SILICON

DLA MS25225 REV J-2007 3位开关保险

This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the switch described herein shall consist of this specification and the latest issue of MIL-DTL-7703.

GUARD, SWITCH, 3 POSITION

DLA SMD-5962-06252-2007 四信道模拟开关混合微型电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, ANALOG SWITCH, QUAD CHANNEL