53.020.01 起重设备综合 标准查询与下载

GSO ISO 7363:2007 起重机和起重设备：技术特性和符合规范的文件

This International Standard establishes the form of presen-tation and content of the documents which a manufacturershould provide with craes and lifting appliances (hereafter called "equipment"). Such documents give technical informa-tion and include acceptance documents for the equipment to facilitate its installation, testing and use. Specimen acceptance documents are given in the annex.

Cranes and Lifting Appliances – Technical Characteristics and Acceptance Documents

SANS 4308-2:2007 起重机和提升设备．钢丝绳的选用．第2部分：流动式起重机，利用系数

Establishes the values of the minimum practical coefficient of utilization, Zp, as defined in ISO 4308-1 (published in South Africa as an identical adoption under the designation SANS 4308-1), for ropes and rotation-resistant ropes used on mobile cranes.

Cranes and lifting appliances - Selection of wire ropes Part 2: Mobile cranes - Coefficient of utilization

ANSI A10.22-2007 构筑和拆除工作用导绳和非引导工人升降机的安全要求

This standard establishes minimum safety requirements for temporary personnel hoisting systems used for the transportation of persons to and from working elevations during normal construction and demolition operations, including maintenance, and is restr

Safety Requirements for Rope-Guided and Nonguided Workers' Hoists for Construction and Demolition Operations

CNS 14965-2006 高空工作车

本标准适用于作业台高度在2 m以上之高空工作车。但下列列举者，则不适用。1.1 特殊构造之高空工作车及其构造部分。1.2 行驶于道路应符合交通运输法令之规定，可不适用本标准第3节(供移动之原动机、动力传达装置、移动装置、操纵装置及制动装置)、第4.3节、第5.15节(移动装置

Engineering vehicle for line-men

JIS A 4302:2006 电梯、自动扶梯、轻型运货升降机的检查标准

この規格は，建築物，工作物などに設置したエレべーター(段差解消機及びいす式階段昇降機を含む。)，エスカレーター（動く歩道を含む。)及び小荷物専用昇降機の安全について検査するための検査項目，検査器具，検査方法及び判定基準について規定する。

Inspection standard of elevator, escalator and dumbwaiter

SANS 10314-2:2006 垂直提升作业平台．操作和维护．第2部分：自推进式高空作业平台

This part of SANS 10314 is applicable to the operation, maintenance, documentation, inspection and training of personnel of self-propelled power-operated integral-chassis elevating aerial platforms that have their primary functions (including the drive) controlled from the platform, that cannot be configured with their centre of gravity completely beyond the base and that are used to position personnel, with their tools and materials, at elevated work locations (see figure 1). 2 This part of SANS 10314 is not applicable to a) ladders and ladder stands, b) scaffolding, c) vehicle-mounted elevating and rotating aerial platforms, d) non-self-propelled elevating aerial platforms, NOTE Mobile manually propelled elevating aerial platforms are dealt with in SANS 10314-1. e) self-propelled aerial platforms with boom supports, f) vehicle-mounted vertical lift devices for airliner ground-support vehicle-mounted vertical lifts, g) vehicle-mounted bridge inspection and maintenance devices, h) mast-climbing work platforms, i) suspended powered platforms for exterior building maintenance, j) vertically adjustable equipment used primarily to raise and lower materials and equipment from one elevation to another, k) fire-fighting equipment, I) construction and demolition operation/digger derricks, and m) any attachment or device that is intended to convert an elevating aerial platform that is non-self- propelled into a self-propelled elevating aerial platform, unless the resulting elevating aerial platform falls within the scope of 1.1.

Vertical lift elevating work platforms - Operation and maintenance Part 2: Mobile self-propelled elevating aerial platforms

SANS 4308-1:2005 起重机和提升设备．钢丝绳的选用．第1部分：总则

Specifies two methods for the selection of wire ropes to be used on lifting appliances. Establishes the minimum requirements for acceptable strength and performance levels with respect to design, application and maintenance of the lifting appliance.

Cranes and lifting appliances - Selection of wire ropes Part 1: General

SANS 10314-1:2005 垂直提升作业平台．操作和维护．第1部分：手动推进式高空作业平台

This part of SANS 10314 is applicable to the operation, maintenance, documentation, inspection and training of personnel of manually propelled or towed integral-chassis elevating aerial platforms that are adjustable by manual or powered means, that cannot be configured with their centre of gravity completely beyond the base and that are used to position personnel, with their tools and materials, at elevated work locations (see figure 1). 2 This part of SANS 10314 is not applicable to a) ladders and ladder stands, b) scaffolding, c) vehicle-mounted elevating and rotating aerial platforms, d) self-propelled elevating aerial platforms, e) safety requirements for airliner ground-support vehicle-mounted vertical lift devices, f) vehicle-mounted bridge inspection and maintenance devices, g) mast-climbing work platforms, h) suspended powered platforms for exterior building maintenance, i) vertically adjustable equipment used primarily to raise and lower materials and equipment from one elevation to another, and j) fire-fighting equipment.

Vertical lift elevating work platforms - Operation and maintenance Part 1: Mobile manually propelled elevating aerial platforms

JB/T 9008.2-2004 钢丝绳电动葫芦.第2部分:试验方法

本部分规定了一般用途钢丝绳电动葫芦的基本试验要求、试验类别以及各项试验的检测方法。 本部分主要适用于一般用途钢丝绳电动葫芦，并以产品设计工作级别作为试验的基准条件。其他特殊用途的电动葫芦亦可参照采用。

Electric wire rope hoists Part 2: Testing method

JB/T 9008.1-2004 钢丝绳电动葫芦.第1部分:型式与基本参数、技术条件

本部分规定了钢丝绳电动葫芦的型式与基本参数、技术要求、检验规则及标志、包装、运输、贮存等内容。 本部分适用于一般用途的电动葫芦，特殊用途的电动葫芦可以参照采用。

Electric wire rope hoists Part 1: Types and basic parameter, specification

SH/T 3515-2003 大型设备吊装工程施工工艺标准

本标准制订了石油化工大型设备吊装的施工工艺及其安全技术要求。适用于石油化工工程建设大型设备吊装的施工。一般型及小型工件的吊装施工可参照使用。

Construction standard for large-size equipment hoisting engineering

SH/T 3536-2002 石油化工工程起重施工规范

Lifting Construction Specification for Petrochemical Engineering

SANS 7363:2002 起重机和提升装置．技术性能和验收文件

Establishes the form of presentaton and content of the documents which a manufacturer should provide with cranes and lifting appliances (hereafter called "equipment").

Cranes and lifting appliances - Technical characteristics and acceptance documents

SANS 4301-1:2002 起重机和提升设备．分类．第1部分：总则

Establishes a general classification of cranes based on the number of operating cycles to be carried out during the expected life of the crane and a load spectrum factor which represents a nominal state of loading.

Cranes and lifting appliances - Classification Part 1: General

JB/T 2104-2002 油压千斤顶

本标准规定了手动油压千斤顶的产品型式、要求、检验方法、检验规则、标志、包装和贮存。 本标准适用于车辆、工矿、船舶及建筑工程等手动油压千斤顶。其他类似型式的油压千斤顶亦可参照使用。

Specification for hydraulic jacks

KS B ISO 7363-2002(2012) 起重机和起重机械技术特性和验收文件

Cranes and lifting appliances－Technical characterisitics and acceptance documents

ASTM A952/A952M-02 锻造80级和100级钢提升部件和焊接附件链接标准规范

1.1 This specification covers the requirements for forged alloy steel lifting components and welded coupling and master links for Grade 80 and Grade 100 alloy chain slings as described in Specification A 906/A 906M. 1.2 Two grades of components and welded links are covered:1.2.1 Grade 80.1.2.2 Grade 100.1.3 This specification is a performance standard. Other standards apply to use of these products. Some of these standards are: OSHA 1910.184, ASME B30.10, and ASME B30.9. 1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Forged Grade 80 and Grade 100 Steel Lifting Components and Welded Attachment Links

SANS 4301-2:2002 起重机械．分类．第2部分：流动式起重机

This part of ISO 4301 establishes a classification of mobile cranes and related crane mechanisms based on the number of operating cycles to be carried out during the expected life of the mobile crane or mechanism and on a load spectrum factor which represents a nominal state of loading. It applies to basic types of self-propelled mobile cranes and their parts as defined in ISO 4306/2.

Lifting appliances - Classification - Part 2: Mobile cranes

JIS B 8832:2001 提升设备.能力

この規格は，JIS B 8802， JIS B 8819, JIS B 8815, JIS C 9620, JIS B 8813の巻上機(以下，巻上機という。)の定格荷重について規定する。

Lifting equipments -- Capacities

JB/T 10222-2001 防爆钢丝绳电动葫芦

标准化规定了防爆钢丝绳电动葫芦的分类、技术要求、试验、检验规则及标志、包装、运输、贮存等内容。 本标准用于煤矿井下(Ⅰ类)和工厂(Ⅱ类)在有爆炸性气体环境中工作的防爆葫芦。 本标准不适用于在爆炸性粉尘环境中工作的防爆葫芦。

Specification for explosion-proof electric wire rope hoists