71.080.01 有机化学综合 标准查询与下载

ASTM E1858-23 用差示扫描量热法测定碳氢化合物氧化诱导时间的标准试验方法

1.1 These test methods describe the determination of the oxidative properties of hydrocarbons by differential scanning calorimetry or pressure differential scanning calorimetry and is applicable to hydrocarbons that oxidize exothermically in their analyzed form. 1.2 Test Method A—A differential scanning calorimeter (DSC) is used at ambient pressure, for example, about 100 kPa of oxygen. 1.3 Test Method B—A pressure DSC (PDSC) is used at high pressure, for example, 3.5 MPa (500 psig) oxygen. 1.4 Units—The values stated in SI units are to be regarded as standard. Imperial units are provided for user convenience and are not the standard. 1.5 These test methods are related to ISO 11357–6 but is different in technical content. These test methods are related to CEC L-85–T but includes additional experimental conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 7.4 and 12.10. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Determining Oxidation Induction Time of Hydrocarbons by Differential Scanning Calorimetry

ASTM D7423-23 用气相色谱法和火焰离子化检测法测定C2、C3、C4和C5碳氢化合物基质中氧合物的标准试验方法

1.1 This test method covers the gas chromatographic procedure for the quantitative determination of organic oxygenates in C2, C3, C4, and C5 matrices by multidimensional gas chromatography and flame ionization detection. This test method is applicable when the hydrocarbon matrices have a final boiling point not greater than 200 °C. Oxygenate compounds include, but are not limited to, those listed in Table 1. The linear working range for oxygenates is 0.50 mg ⁄kg to 100 mg ⁄kg. 1.2 This test method is intended to determine the mass concentration of each oxygenate in the hydrocarbon matrix. Oxygenate compound identification is determined by reference standards and column elution retention order. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities. The eLearning training course “Liquefied Petroleum Gases Sampling Safety” is available on the ASTM.org website. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Oxygenates in C2, C3, C4, and C5 Hydrocarbon Matrices by Gas Chromatography and Flame Ionization Detection

ASTM D1157-23 轻质烃的总抑制剂含量（TBC）的标准试验方法

1.1 This test method covers the determination of total p-tertiary-butylcatechol inhibitor added to polymerization and recycle grades of butadiene or to other C4 hydrocarbon mixtures containing no phenolic material other than catechol or no oxidized phenolic material other than that derived from oxidation of catechol. In general, all phenols and their quinone oxidation products are included in the calculated catechol content. Small amounts of polymer do not interfere. This test method is applicable over the range of TBC from 50 mg ⁄kg to 500 mg ⁄kg. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Total Inhibitor Content (TBC) of Light Hydrocarbons

T/CCASC 6003-2022 氯碱工业绿色设计产品评价甘油法环氧氯丙烷

Green Design Product Evaluation of Chlor-Alkali Industry Glycerin Method Epichlorohydrin

T/QGCML 471-2022 有机烷烃精炼费托蜡

本标准规定了有机烷烃精炼费托蜡的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输、贮存和注意事项。 本标准适用于有机烷烃精炼费托蜡的生产、检验和验收。

Organic alkanes refining Fischer-Tropsch wax

T/SDEPI 014-2022 苯酚残液蒸馏脱酚油生产古马隆-茚树脂

本文件规定了苯酚残液蒸馏脱酚油生产古马隆-茚树脂的原料及流程、要求、试验方法、检验规则、标志、标签、包装和运输、贮存。

Coumarone-indene resin which produced by dephenolized phenol oil rectified from phenol of residual liquid

T/CCASC 2002-2022 医用级聚氯乙烯专用树脂

1 范围　 2 规范性引用文件　 3 术语和定义　 4 技术要求　 5 试验方法　 6 检验规则　 7 标志、包装、运输和贮存 附　录　A （规范性） 1，2-二氯乙烷的测定　 附　录　B （规范性） 重金属(Pb、Zn、Cu、Cr)的测定　

Medical grade of polyvinyl chloride special resin

KS M 1988-2022 工业用1,4-丁二醇 不饱和度的测定

Butane-1,4-diol for industrial use — Determination of degree of unsaturation

T/SPSTS 040-2022 锂离子电池用N-甲基-2-吡咯烷酮溶剂原料和产品质量

1 范围　 2 规范性引用文件　 3 术语和定义　 4 缩略语　 5 检验规则　 附录A （资料性） NMP溶剂原料和成品不是危险化学品的说明 附录B （资料性） 精馏前原料NMP溶剂不是固固体废物的说明　 附录C （资料性） NMP溶剂不是挥发性有机液体说明　

Quality standard of NMP solvent as raw material and product for lithium ion batteries

GSO ASTM D4308:2022 用精密仪器测量液态烃电导率的标准测试方法

1.1 This test method covers and applies to the determination of the “rest” electrical conductivity of aviation fuels and other similar low-conductivity hydrocarbon liquids in the range from 0.1 to 2000 pS/m (see 3.1.2). This test method can be used in the laboratory or in the field. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 7.1.1, 7.2, 8.3, and Annex A1.

Standard Test Method for Electrical Conductivity of Liquid Hydrocarbons by Precision Meter

GSO ASTM D1078:2022 挥发性有机液体蒸馏范围的标准测试方法

1.1 This test method covers the determination of the distillation range of liquids boiling between 30 and 350 °C, that are chemically stable during the distillation process, by manual or automatic distillation procedures. 1.2 This test method is applicable to organic liquids such as hydrocarbons, oxygenated compounds, chemical intermediates, and blends thereof. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.5 For hazard information and guidance, see the supplier’s Material Safety Data Sheet. 1.6 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercurycontaining products, or both, in your state may be prohibited by state law.

Standard Test Method for Distillation Range of Volatile Organic Liquids

T/NAIA 0104-2022 副产硫酸镁生产技术规范

本文件规定了副产硫酸镁的要求，试验方法，检验规则，标志、标签，包装、运输和贮存。 本文件适用于采用微通道连续流技术生产2-硝基-4-甲砜基苯甲酸生产过程中介质硫酸与工业氧化镁制备硫酸镁。

Technical specifications for the production of by-product magnesium sulfate

T/NAIA 0107-2022 副产氯化钠生产技术规范

本文件规定了副产氯化钠生产的术语和定义、原料要求、设备要求、工艺基本条件以及生产要求。 本文件适用于企业在氯代胺连续化生产过程中产生的氯化钠经无害化处理后制备的副产品氯化钠。

Technical specifications for the production of by-product sodium chloride

T/CIESC 0025-2022 工业用N,N-二甲基环己胺

本文件规定了工业用N,N-二甲基环己胺（DMCHA）的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以环己胺为原料，经甲醛加氢工艺生产的N,N-二甲基环己胺，以及以环己酮为原料，经二甲胺加氢工艺生产的N,N-二甲基环已胺。

N,N-Dimethylcyclohexylamine（DMCHA）for industrial use

T/SDEPI 023-2021 工业副产有机溶剂稀料

本文件规定了工业副产有机溶剂稀料的要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以二氯乙烯单体、氯乙烯单体、乙烯直接氯化生产二氯乙烷过程中产生的重馏分为原料，经过蒸馏制得的工业副产有机溶剂稀料，主要用于溶剂、稀料和油脂、橡胶的稀释剂使用。

By-product organic solvent thinner

T/CRIA 20002-2021 炭黑原料油 煤焦油

本文件规定了煤焦油技术要求、试验方法、检验规则、包装、标志、储存、运输和质量证明书。 本文件适用于炭黑生产用原料油。

Carbon Black Raw Oil Coal Tar

ASTM D5351-93(2021) 用萃取滴定法测定有机结合硫酸酐的标准试验方法 试验方法B

1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by extracting the undecomposed sulfated fat and other fatty matter over an acidulated, concentrated salt solution, boiling the residue with sulfuric acid after evaporating the solvent, and titrating the products of reaction. This test method is applicable only to sulfated oils that split off their combined SO3 upon boiling with mineral acids, including samples containing sodium acetate or other compounds that cannot be accurately titrated in water solution with methyl orange as the indicator. This test method was derived from Test Methods D500, Sections 20 through 24, and ALCA Method H-43. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Extraction Titration, Test Method B

KS M 1501-2021 磷 红色

Phosphorus, red

KS M 2712-2021 工业用硬化油和脂肪酸

Hardened oils and fatty acids for industrial use

T/NAIA 073-2021 2-噻吩乙酰氯

本文件规定了2-噻吩乙酰氯的质量要求、试验方法、检验规则及标志、包装、运输、贮存。 本文件适用于以噻吩、多聚甲醛、盐酸为原料制备的2-噻吩乙酰氯产品。

2-thiopheneacetyl chloride