71.080.01 有机化学综合 标准查询与下载

T/NAIA 076-2021 反式-3-氯-2-丙烯基羟胺 连续化生产工艺技术规范

本文件规定了反式-3-氯-2-丙烯基羟胺生产的原料要求、设备要求、工艺流程以及生产工艺等要求。 本文件适用于以盐酸羟胺、液碱、乙酸乙酯为起始原料，经酰胺化、醚化、酸解及中和四步反应工序，采用连续流工艺合成反式-3-氯-2-丙烯基羟胺的工艺技术。

Technical specification for continuous production process of trans-3-chloro-2-propenyl hydroxylamine

T/NAIA 072-2021 2-噻吩乙酰氯生产技术规范

本文件规定了2-噻吩乙酰氯合成生产的术语和定义、原料要求、设备要求、工艺基本条件以及生产要求。 本文件适用于以噻吩、多聚甲醛、盐酸等为原料制备的2-噻吩乙酰氯的生产加工。

Technical specifications for the production of 2-thiopheneacetyl chloride

T/NAIA 077-2021 反式-3-氯-2-丙烯基羟胺

本文件规定了连续流工艺及釜式工艺生产反式-3-氯-2-丙烯基羟胺的质量要求、试验方法、检验规则及标志、包装、运输、贮存。 本文件适用于以盐酸羟胺、乙酸乙酯、液碱为原料制备的反式-3-氯-2-丙烯基羟胺产品。 化学名：反式-3-氯-2-丙烯基羟胺

trans-3-chloro-2-propenylhydroxylamine

T/SDEPI 011-2021 苯酚残液回收工业用苯酚

本文件规定了苯酚残液回收工业用苯酚的原料及工艺流程、要求、试验方法、检验规则、标志、包装、运输和贮存。 

Industrial phenol which recycled from phenol of residual liquid

T/SDEPI 013-2021 苯酚残液回收工业用α-甲基苯乙烯

本文件规定了苯酚残液回收工业用α-甲基苯乙烯的原料及工艺流程、要求、试验方法、检验规则、标志、标签、包装和运输、贮存。

α-methyl styrene which recycled from phenol of residual liquid

T/SDEPI 012-2021 苯酚残液回收工业用异丙苯

本文件规定了苯酚残液回收工业用异丙苯的原料及工艺流程、要求、试验方法、检验规则、标志、标签、包装、运输和贮存。

Industrial isopropyl-benzene which recycled from phenol of residual liquid

T/NAIA 057-2021 工业用4,6-二氯嘧啶

本文件规定了4,6-二氯嘧啶产品的要求、采样、试验方法、检验规则以及标志（采样、）、标签、包装、运输和贮存。 本文件适用于4,6-二氯嘧啶产品质量控制。

4,6-Dichloropyrimidine for industrial use

T/NAIA 058-2021 工业用2-氨基-4-氯-6-甲氧基嘧啶

本文件规定了2-氨基-4-氯-6-甲氧基嘧啶产品的要求、采样、试验方法、检验规则以及标志、标签、包装、运输和贮存。 本文件适用于2-氨基-4-氯-6-甲氧基嘧啶产品质量控制。

2-Amino-4-chloro-6-methoxypyrimidine for industrial use

T/NAIA 059-2021 工业用2-氨基-4-甲基-6-甲氧基-1,3,5-均三嗪

本文件规定了2-氨基-4-甲基-6-甲氧基-1,3,5-均三嗪产品的质量要求、试验方法、检验规则以及标志、标签、包装、运输和贮存。 本文件适用于2-氨基-4-甲基-6-甲氧基-1,3,5-均三嗪产品的质量控制。

2-Amino-4-methyl-6-methoxy-1,3,5-s-triazine for industrial use

ASTM E502-21a 用闭杯法测定化学品闪点的ASTM标准的选择和使用的标准试验方法

1.1 This test method covers the determination of the flash point of liquid and solid chemical compounds flashing from below −10 to 370°C (16 to 700°F). The procedures and apparatus in Test Methods D56, D93, D3278, D3828, and D3941 are to be used. Modification to these procedures are specified for tests on solids and viscous liquids. The significance of the results obtained is discussed along with possible sources of error and factors that might cause interference. 1.2 Suggestions for adapting this procedure to mixtures of chemicals are included (see Appendix X2). 1.3 This test method should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials or assemblies under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment that take into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website — http:// www.epa.gov/mercury/faq.htm — for additional information. Users should be aware that selling mercury or mercurycontaining products, or both, into your state may be prohibited by state law. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See also Section 8. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods

ASTM E502-21 用于通过闭杯方法测定化学品闪点的ASTM标准的选择和使用的标准测试方法

1.1?This test method covers the determination of the flash point of liquid and solid chemical compounds flashing from below ?10 to 370��C (16 to 700��F). The procedures and apparatus in Test Methods D56, D93, D3278, D3828, and D3941 are to be used. Modification to these procedur

Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods

ASTM D4308-21 精密仪表液体碳氢化合物电导率的标准试验方法

1.1?This test method covers and applies to the determination of the “rest” electrical conductivity of aviation fuels and other similar low-conductivity hydrocarbon liquids in the range from 1 pS/m to 2000 pS/m (see 3.1.2). This test method can be used in the laboratory or in the

Standard Test Method for Electrical Conductivity of Liquid Hydrocarbons by Precision Meter

T/GAMA 13-2020 增材制造 高分子粉末床激光熔融设计规范

规定了高分子聚合物粉末床激光熔融工艺的特征和设计要求，适用于高分子聚合物粉末床激光熔融工艺。

Design specification for polymer powder bed laser fusion for additive manufacturing

T/NAIA 014-2020 甲醇中水分含量的测定 气相色谱法

本标准规定了用气相色谱法测定工业甲醇中水分含量的方法。 本标准适用于甲醇中水分含量。 测定甲醇中水分含量为0.002%-10.0%。

Determination of Moisture Content in Methanol by Gas Chromatography

ASTM D1157-91(2019) 轻烃总抑制剂含量（TBC）的标准试验方法

1.1 This test method covers the determination of total p-tertiary-butylcatechol inhibitor added to polymerization and recycle grades of butadiene or to other C4 hydrocarbon mixtures containing no phenolic material other than catechol or no oxidized phenolic material other than that derived from oxidation of catechol. In general, all phenols and their quinone oxidation products are included in the calculated catechol content. Small amounts of polymer do not interfere. This test method is applicable over the range of TBC from 50 mg ⁄kg to 500 mg ⁄kg. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Total Inhibitor Content (TBC) of Light Hydrocarbons

ASTM D1078-11(2019) 挥发性有机液体蒸馏范围的标准试验方法

1.1 This test method covers the determination of the distillation range of liquids boiling between 30 and 350 °C, that are chemically stable during the distillation process, by manual or automatic distillation procedures. 1.2 This test method is applicable to organic liquids such as hydrocarbons, oxygenated compounds, chemical intermediates, and blends thereof. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.5 For hazard information and guidance, see the supplier’s Material Safety Data Sheet. 1.6 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercurycontaining products, or both, in your state may be prohibited by state law. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Distillation Range of Volatile Organic Liquids

T/FSI 026-2019 工业用八氟环丁烷

本标准规定了工业用八氟环丁烷的要求、试验方法、检验规则以及标志、包装、运输、贮存和安全。 本标准适用于由四氟乙烯及六氟丙烯生产过程中的副产物粗八氟环丁烷经精馏、干燥等过程得到的八氟环丁烷。生产过程中的副产物粗八氟环丁烷经精馏、干燥等过程得到的八氟环丁烷。 分子式：C4F8　 分子量：200 CAS号：115-25-3

Octafluorocyclobutane for industrial use

ASTM D5350-95(2019) 滴定法测定有机结合的硫酸酐的标准试验方法

1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by boiling the sample with sulfuric acid and determining the acidity of the reaction mixture. This test method is applicable only to oils that split off their combined SO3 upon boiling with mineral acids and that do not contain compounds that cannot be accurately titrated in water solution with methyl orange as the indicator. This test method was derived from Test Methods D500, Sections 15 through 19. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Titration, Test Method A

ASTM D5352-95(2019) 有机硫酸酐重垢测定标准试验方法 试验方法C

1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfonated or sulfated oil, or both, by extracting the undecomposed sulfonated or sulfated fat and other fatty matter over an acidulated, concentrated salt solution, and ashing the purified extract. This test method is applicable to all types of sulfonated and sulfated oils, including true sulfonic acid oils and those containing sodium acetate or similar partially titratable compounds. This test method was derived from Test Methods D500, Sections 25 through 28. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Organically Combined Sulfuric Anhydride Ash-Gravimetric, Test Method C

T/CTES 1014-2019 纺织用酶 α-淀粉酶

本标准规定了纺织行业用液体α-淀粉酶制剂的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输及储存。 本标准适用于纺织行业织物前处理退浆及成衣水洗的α-淀粉酶制剂产品。

Textile enzyme alpha-amylase