75.140 石蜡、沥青材料和其他石油产品 标准查询与下载

GSO ASTM D95:2023 通过蒸馏测定石油产品和沥青材料中水的标准测试方法

  Scope is not provided for this standard

Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

ASTM D5869/D5869M-07a(2023) 屋顶和防水材料的暗箱热暴露的标准实施规程

1.1 This practice establishes a procedure and conditions of temperature and time for heat exposure of roofing and waterproofing materials and systems in the presence of air. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials

ASTM D2746/D2746M-18(2023) 沥青染色趋势的标准试验方法（染色指数）

1.1 This test method covers the determination of the staining tendency of asphalt and the assignment of a stain index proportional to the extent of staining observed. 1.2 This test method is applicable to asphalts having ringand-ball softening points of 85 °C [185 °F] or greater. NOTE 1—This test method may be modified for use with other bituminous materials with softening points less than 85 °C [185 °F] by using a different temperature than specified in Section 7 by agreement of the interested parties. The report of results from such a test may cite this method but must clearly state the temperature employed in the exception and acknowledge that the interpretation of results in Section 9 and the precision and bias stated in Section 10 may not apply. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Staining Tendency of Asphalt (Stain Index)

T/CIPR 025-2023 再生沥青混合料

本文件规定了再生沥青混合料的技术要求、试验方法、检验规则和运输。 本文件适用于路面铺设的再生沥青混合料及其制备方法。

recycled asphalt mixture

T/CIPR 024-2023 透水沥青

本文件规定了透水沥青的技术要求、试验方法、检验规则和运输。 本文件适用于路面铺设的透水沥青及其制备方法。

permeable asphalt

T/CIPR 022-2023 环保沥青混合料

本文件规定了环保沥青混合料的技术要求、试验方法、检验规则和运输。 本文件适用于路面铺设的沥青混合物及其制备方法。

Environmental protection asphalt mixture

T/CIPR 023-2023 沥青混合料

本文件规定了沥清混合料的技术要求、试验方法、检验规则和运输。 本文件适用于路面铺设的沥青混合物及其制备方法。

Asphalt

ASTM D4799/D4799M-17(2023) 沥青材料加速老化试验条件和程序的标准实施规程（荧光紫外、喷水和冷凝法）

1.1 This practice describes test conditions and procedures for fluorescent UV and condensation exposures conducted according to Practices G151 and G154 for bituminous roofing and waterproofing materials. (See Terminology G113.) 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)

ASTM D6627/D6627M-22 测定冷沥青混合物挥发性馏出物馏分的标准试验方法

1.1 This test method covers the determination, by direct measurement, of the ambient to 260 °C [500 °F] volatile distillate fraction of cold mix asphalt mixtures. 1.2 A precision and bias statement for this test method has not been developed since this test method is used for research purposes or information only. Therefore this test method should not be used for acceptance or rejection of a material for purchasing purposes. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of a Volatile Distillate Fraction of Cold Asphalt Mixtures

ASTM D7552-22 使用动态剪切流变仪测定沥青混合料复合剪切模量（G*）的标准试验方法

1.1 This test method covers the determination of the complex shear modulus of asphalt mixtures using torsion rectangular geometry on a dynamic shear rheometer (DSR). It is applicable to asphalt mixtures having complex shear modulus values greater than 1 × 104 Pa when tested over a range of temperatures from –40 °C to 76 °C at frequencies of 0.01 to 25 Hz and strains of 0.0005 % to 0.1 %. The determination of complex shear modulus is typically determined at 20 °C to 70 °C at 0.01 % strain at ten discrete frequency values covering 0.01 to 10 Hz. From these data, temperature or frequency master curves can be generated as required. This test method is intended for determining the complex shear modulus of asphalt mixtures as required for specification testing or quality control of asphalt mixture production. 1.2 This test method is appropriate for laboratory-prepared and compacted mixtures, field-produced and laboratorycompacted mixtures or field cores, regardless of binder type or grade and regardless of whether RAP is used in the mixture. Due to the geometry of the specimens being tested this test method is not applicable to open-graded or SMA mixtures. It has been found to be appropriate for dense-graded mixtures, whether coarseor fine-graded, with 19 mm or smaller nominal maximum aggregate size. 1.3 Since a precision estimate for this standard has not been developed, the test method is to be used for research and informational purposes only. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Complex Shear Modulus (G*) of Asphalt Mixtures Using Dynamic Shear Rheometer

ASTM D5361/D5361M-16(2022) 实验室试验用压实沥青混合料取样的标准实施规程

1.1 This practice describes a procedure for removal of a sample of compacted asphalt mixture from a pavement for laboratory testing. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing

ASTM D1386-15(2022) 合成和天然蜡酸值（经验值）的标准试验方法

1.1 This test method covers the determination of the acid number of synthetic waxes and natural waxes. The number is obtained by direct titration of the material and indicates the amount of free acid present. 1.2 This test method, using an ethanol-xylene mixture, is applicable to all natural waxes, including carnauba. The test method is also applicable to oxidized microcrystalline waxes, oxidized Fischer-Tropsch, oxidized polyethylene, and montan esters. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Acid Number (Empirical) of Synthetic and Natural Waxes

KS M 5960-2022 清漆 沥青

Varnish, asphalt

T/SHMHZQ 059-2022 特种蜡产品研发流程规范

1 范围 2 规范性引用文件 3 术语和定义 4 基本要求 5 主要部门职责 5.1 市场部 5.2 研发部 5.3 生产部 5.4 品质部 5.5 采购部 5.6 管理部 6 研发基本流程 6.1 市场调研 6.2 技术调研 6.3 实验室研究 6.4 可行性论证 6.5 小试 6.6 模型试验 6.7 中试 6.8 样品检验 6.9 成果输出 6.10 持续改进 7 技术经济评价 7.1 初步评价 7.2 中间评价 7.3 最终评价

Special wax product research and development process specification

T/SHMHZQ 058-2022 特种蜡生产过程流程规范

1 范围 2 规范性引用文件 3 术语和定义 3.1 特种蜡 4 基本要求 5 生产原理 5.1 物理改性 5.2 化学改性 6 生产流程 6.1 生产指令 6.2 生产前准备 6.3 小规模试制 6.4 产品检验 6.5 规模化生产 6.6 入库交付 7 质量控制 7.1 制度控制 7.2 原料控制 7.3 人员控制 7.4 生产控制 7.5 贮存控制

Special wax production process flow specification

KS F 2363-2022 沥青表面处理材料用量的标准实施规程

Standard practice for quantities of materials for asphalt surface treatments

KS F 2337-2022 使用马歇尔装置测定沥青混合料马歇尔稳定性和流动性的测试方法

Testing method for marshall stability and flow of asphalt mixtures using marshall apparatus

KS F 2367-2022 压实沥青铺路混合料试件厚度或高度的测试方法

Testing method for thickness or height of compacted asphalt paving mixture specimens

KS F 2379-2022 落锤式冲击载荷装置挠度试验方法

Testing method for deflections with a falling-weight-type impulse load device

KS F 2381-2022 Abson从溶液中回收沥青的试验方法

Testing method for recovery of asphalt from solution by Abson