77.180 冶金设备 标准查询与下载

YB/T 4056-2021 金属板材矫正机工作辊技术条件

Technical conditions for work rolls of sheet metal straightening machines

T/SSEA 0102-2021 可控流物料转运系统

本文件规定了可控流物料转运系统的术语和定义、型式与参数、技术要求、试验方法、检验规则、供货要求、标志、包装、运输和贮存。 本文件适用于钢铁行业铁矿石、铁精粉、煤、焦炭、熔剂等块状和粉状物料的转运。

Controlled Flow Material Transfer System

T/CISA 070-2020 工业机器人热成型模锻智能装备

本标准规定了工业机器人热成型模锻智能装备的订货内容、形式、要求、试验方法、检验规则、包装、标志和交付。

Industrial Robot Thermoforming Die Forging Intelligent Equipment

T/CISA 069-2020 高速金属智能冷锯机

本标准规定了高速金属智能冷锯机的术语和定义、分类、型号表示方法、结构、技术参数、要求、试验方法、检验规则、标志、使用说明书、包装、运输、贮存、订货内容。

High-speed metal intelligent cold sawing machine

T/CAMIE 12-2020 《真空石墨化炉》

目前真空石墨化炉属于非标产品，没有统一的分类、基本参数、尺寸规格、型号及型号表示规则。行业内对这类设备的性能需求无统一尺度衡量，无相应的国家标准、行业标准和地方标准可作产品标准执行。编制组根据多年来所生产的真空石墨化炉的实际应用情况，结合高温处理行业的需求情况，湖南顶立科技有限公司同北京工业大学、自贡长城装备技术有限责任公司、安徽弘昌新材料有限公司和湖南科西机械技术有限公司等科研单位、装备研制和使用单位，对真空石墨化炉的系统组成、性能特点进行了总结，并总结形成《真空石墨化炉》标准。 编制组从以下方面对真空石墨化炉进行规范： 1)统一了设计和制造规范 规范了真空石墨化炉总体设计和制造要求，使设备设计和制造有据可依。 2)统一出厂和验收规范 规范真空石墨化炉出厂检验和需方验收内容，做到设备出厂检验和需方验收有据可依。  3)统一了基本分类 根据结构形式和装料方式分为卧式双开门真空石墨化炉、卧式单开门真空石墨化炉、立式上装料真空石墨化炉和立式下装料真空石墨化炉等4种炉型。

Vacuum Graphitization Furnace

T/SSEA 0064-2020 水封式烧结环冷机

本标准规定了水封式烧结环冷机的术语和定义、型式与基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于钢铁行业上下水密封式烧结环冷机

Water-sealed sintering ring cooler

T/SSEA 0050-2020 带式焙烧机

本标准规定了带式焙烧机的型号与基本参数、正常工作条件、技术要求、试验方法、检验规则、标志、使用说明书、包装、运输和贮存。

Belt roaster

T/CCIAT 0020-2020 冶金工程C型封闭料场设备安装与验收规程

本规程共分11章，主要技术内容有：1 总则、2 术语、3 基本规定、4 施工准备、5 门式刮板堆取设备安装、6 卸料车安装、7 带式输送机安装、8 辅助设施安装、9 设备试运转、10 环境、职业健康与安全、11 验收、12 附录。

Installation and acceptance regulations for C-type closed stockyard equipment in metallurgical engineering

JB/T 13765-2020 钨钼板冷轧机 通用技术条件

General technical conditions for tungsten-molybdenum plate cold rolling mill

JB/T 13766-2020 钨钼板热轧机 通用技术条件

General technical conditions for tungsten-molybdenum plate hot rolling mill

T/CFA 0203121-2020 自激式湿式除尘器

本标准规定了自激式湿式除尘器的（以下简称除尘器）的术语和定义、规格、型号及基本参数、要求、试验方法、检验规则、标志和使用说明书、包装、运输、贮存等。 本标准适用于冶金、铸造、机械加工、建材行业各工序粉尘、酸碱废气的吸收净化。

Self-excited wet dust collectors

T/CFA 020101161-2020 铸造高速钢轧辊

本标准规定了铸造高速钢轧辊的技术要求、试验方法、检验规则、标识、包装、质量证书和超声波探伤方法。 本标准适用于金属材料压延加工使用轧辊工作层为高速钢材质的铸造高速钢复合轧辊（含辊环）的制造与验收。

Cast high speed steel rolls

T/YKJSX 0005-2020 再生铸造铝及铝合金生产技术规范

典型再生铸造铝及铝合金生产工艺, 典型的再生铝原料预处理工艺, 配料时应根据加工企业的产品技术要求及用户的使用情况，制定工艺技术文件，确定各类再生铝原料的数量配比; 熔化工艺宜采用“低温浸没”原则，以降低熔炼过程中的铝损及能源损耗; 炉料熔化后应充分搅拌,取样进行炉前快速分析,按检测结果调整化学成分,满足标准要求后,宜进行炉内精炼,精炼后须静置,然后开始铸造; 针对不同品质要求的铝及铝合金铸锭产品，在铸造时宜配备相应的在线净化设备,必要时可以使用在线测氢、测渣等检测仪器，以保证铸锭的内部金属纯净度，熔炼工艺及设备可参照GB/T 34640要求执行，纯净度参照GB/T 32186 要求执行

Technical Specification of Regenerated Casting Aluminum and Aluminum Alloy

YB/T 4782-2019 真空自耗炉结晶器

Vacuum consumable furnace crystallizer

ASTM F1348/F1348M-91(2019) 气动旋转除垢机标准规格

1.1 This specification covers requirements for pneumatic rotary descaling machines for removal of paint, rust, scale, nonskid deck covering, and other coatings from steel and aluminum structures. These portable machines are intended for use in a marine environment, subject to salt air and spray during use and high humidity during storage. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary statement pertains to the test method portion only, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 17.2.1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pneumatic Rotary Descaling Machines

19/30394748 DC BS EN 15093 机械安全 热平轧机安全要求

BS EN 15093. Safety of machinery. Safety requirements for hot flat rolling mills

YB/T 4139-2019 连续铸钢电磁搅拌器

Continuous cast steel electromagnetic stirrer

ASTM D5224-12(2019) 热固性模塑化合物压缩模塑试样的标准实施规程

1.1 This practice covers the general principles to be followed when compression molding test specimens of thermosetting molding compounds, such as phenolics, aminoplastics, melamine phenolics, epoxies, and unsaturated polyesters. 1.2 Molding conditions are given for amino, phenolic, and allyl molding compounds. The exact molding conditions will vary from material to material, and, if not incorporated in the material specification, shall be agreed upon between the purchaser and the supplier or determined by previous experience with the particular type of material being used 1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are given for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This standard and ISO 295 address the same subject matter, but differ in technical content. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds

ASTM E2349-19 金属铸造操作安全要求的标准实践:砂准备 成型和核心制造;熔化和浇注和清洁和整理

1.1 This practice covers the requirements of applying the design, construction, and operation of the machinery and equipment used in metal casting operations—sand preparation, molding and core making, melting and pouring, and cleaning and finishing. This practice does not apply to die casting operations. 1.2 Purpose—The requirements of this practice, including the training of supervisors and employees, are intended to minimize the possibility of injury to operating and maintenance personnel while working on, or in the vicinity of, the specified equipment. Compliance with this practice, in conjunction with OSHA regulations, provides a relatively safe environment, which is a fundamental requisite in helping to prevent occupational injuries. 1.3 Application: 1.3.1 New Installations—After the date of publication, all new installations within the scope of this specification shall be in conformance with its requirements. Any existing machine installation moved to a new plant or another location in the same plant is deemed a new installation when it is installed in the new location. However, an existing installed machine (former installation) that is moved for a short distance, for example, to provide additional aisle space, is not deemed to be a new installation. 1.3.2 Existing Installations—After the approval date of this practice, installations existing on, or before, this date shall be modified as necessary to be in conformance with all requirements of this practice. Where it is not practical to modify an existing facility in conformance with this practice, deficiencies shall be noted and plans for compliance shall be included in any future facility or equipment changes. Those facilities and equipment on order or in the process of construction on the date of publication of this practice shall be considered as an existing installation. This practice applies to existing equipment if it lacks the necessary employee protection (personal protective equipment or administrative controls). 1.4 The values stated in inch/pound units are to be regarded as the standard. The values in brackets are for information only. 1.5 The text of this practice references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing

T/CNIA 0029.3-2019 镁冶炼生产专用设备 第3部分：冷却器

本部分规定了产品分类和型号、要求、试验方法、检验规则、标志、包装、运输和贮存。 本部分适用于热还原法冶炼金属镁生产用冷却器。

Special Equipment for Magnesium Smelting Production Part 3: Cooler