79.060.01 木基板材综合 标准查询与下载

DIN EN ISO 12460-5:2016 木基板材.甲醛释放的测定.第5部分:萃取法(又称穿孔法)(ISO 12460-5-2015).德文版本EN ISO 12460-5-2015

Wood-based panels - Determination of formaldehyde release - Part 5: Extraction method (called the perforator method) (ISO 12460-5:2015); German version EN ISO 12460-5:2015

BS EN 16718:2015 木材和木制品 木材和木制品中总有机碳 (TOC) 的用量

What is BS EN 16718 – Total organic carbon content in wood products about?    BS EN 16718 describes a method for determining total organic carbon by calculating the difference between the results of measurements of total carbon (TC) and total inorganic carbon (TIC). The identification of the bio-based content given by the stable isotopes such as 13C is described also.    This method is applicable to all wood species, wood-based materials (panels, plywood, wood-polymer, etc.) and woods containing chemicals in general.   Who is BS EN 16718 – Total organic carbon content in wood products for?   BS EN 16718 on the dosage of the total organic carbon (TOC) in wood and wood-based products is useful for:   Manufacturers of wood and wood-based products (panels, plyw...

Wood and wood based products. Dosage of the total organic carbon (TOC) in wood and wood based products

DIN EN ISO 12460-3:2016 木材.甲醛释放测定.第3部分:气体分析法(ISO 12460-3-2015).德文版本EN ISO 12460-3-2015

Wood-based panels - Determination of formaldehyde release - Part 3: Gas analysis method (ISO 12460-3:2015); German version EN ISO 12460-3:2015

BS EN ISO 12460-4:2016 木基板材. 甲醛释放量的测定. 干燥器法

Wood-based panels. Determination of formaldehyde release. Desiccator method

EN ISO 12460-4:2016 人造板.甲醛释放量的测定.第4部分:干燥器法(ISO 12460-4:2016)

Dieser Teil der ISO 12460 legt ein Exsikkator-Verfahren (Desiccator-Verfahren) zur quantitativen Bestimmung des aus Spanplatten, Faserplatten, Sperrholz, Platten aus langen, flachen, ausgerichteten Spänen (OSB) und schichtverklebten Bodenbelägen aus Holz emittierten Formaldehyds fest.

Wood-based panels - Determination of formaldehyde release - Part 4: Desiccator method

ISO 12460-4:2016 木基板材. 甲醛释放的测定. 第4部分: 干燥器法

Wood-based panels - Determination of formaldehyde release - Part 4: Desiccator method

SNI 5008.2-2016 通用胶合板

Kayu lapis penggunaan umum

SNI 5010.4-2016 林业支持 第 4 节：用材林产品名称

Pendukung di bidang kehutanan - Bagian 4: Nama produk hasil hutan kayu

BS EN ISO 12460-5:2015 木基板.甲醛释放量的测定.钻孔萃取法

Wood-based panels. Determination of formaldehyde release. Extraction method (called the perforator method)

GSO ISO 12460-5:2015 人造板甲醛释放量的测定 第5部分：萃取法（称穿孔法）

  Scope is not provided for this standard

Wood-based panels -- Determination of formaldehyde release -- Part 5: Extraction method (called the perforator method)

GSO ISO 27528:2015 人造板 螺钉轴向拔出阻力的测定

  Scope is not provided for this standard

Wood-based panels -- Determination of resistance to axial withdrawal of screws

GSO ISO 16572:2015 木结构 木板 结构性能测试方法

  Scope is not provided for this standard

Timber structures -- Wood-based panels -- Test methods for structural properties

GSO ISO 12460-3:2015 木质板甲醛释放量的测定 第3部分：气体分析方法

  Scope is not provided for this standard

Wood-based panels -- Determination of formaldehyde release -- Part 3: Gas analysis method

ASTM D7989-15 用木结构面板对木框剪力墙进行等效平面横向抗震性能的标准实践

5.1 This practice documents cyclic performance benchmarks for shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using common or box nails as defined in 3.2.8. 5.2 Procedures described in this practice provide a method to evaluate an alternative shear wall system’s SEPs to demonstrate equivalent in-plane lateral seismic performance to the reference shear wall system. 5.3 The procedures described in this practice do not address all factors to be considered for recognition of an alternative shear wall system. Such factors, as described in 1.4, vary by the end-use application and shall be addressed outside the scope of this standard through an evaluation of the acceptability of the alternative shear wall system in accordance with requirements of building codes and standards, as applicable. 1.1 This practice establishes a method for alternative shear wall systems to compare seismic equivalency parameters (SEP) derived from cyclic in-plane racking tests to performance targets derived from tests of light-frame shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using nails. 1.2 This practice considers only the performance of shear walls subject to cyclic lateral loading, parallel to the plane of the shear wall. Design of walls with openings and performance for other wall functions, such as out-of-plane bending, combined shear and uplift, etc. are not considered. 1.3 This practice is applicable only to shear walls where all vertical-load-supporting elements are intact at the end of the in-plane lateral load test and remain capable of supporting gravity loads. Wall assemblies whose vertical-load-supporting elements buckle or otherwise become incapable of supporting gravity loads during the lateral load test are outside the scope of this practice. In addition, for bearing wall systems, this practice assumes that the shear wall system under evaluation has documented design procedures to ensure that vertical-load-supporting elements have adequate resistance to the combined effect of compression loads caused by overturning and gravity loads. 1.4 This practice does not address height limitations, detailing requirements, wall openings, derivation of design values for strength and stiffness, or other requirements and limitations that may be necessary for an alternative shear wall system. These requirements shall be provided elsewhere, such as by a suitable product standard for the alternative shear wall system. 1.5 This practice assumes that the stiffness or deformation of the alternative shear wall system can be estimated, and that design loads within a structure will be distributed among seismically equivalent wall systems based on their relative stiffness. 1.6 This practice is not intended to preclude other rational means of evaluating seismic performance. 1.7x0......

Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels

EN ISO 12460-5:2015 人造板.甲醛释放量的测定.第5部分:提取方法(称为穿孔法)(ISO 12460-5:2015)

Dieser Teil von ISO 12460 legt ein Extraktionsverfahren, bekannt als "Perforatormethode" fest. Er wird angewendet für die Bestimmung des Formaldehydgehaltes von unbeschichteten und unlackierten Holzwerkstoffen.

Wood-based panels - Determination of formaldehyde release - Part 5: Extraction method (called the perforator method)

BS EN ISO 12460-3:2015 木质板材.甲醛释放量的测定.气体分析法

Wood-based panels. Determination of formaldehyde release. Gas analysis method

ISO 12460-3:2015 木基板材.甲醛释放的测定.第3部分:气体分析法

Wood-based panels - Determination of formaldehyde release - Part 3: Gas analysis method

ISO 12460-5:2015 木基板材.甲醛释放的测定.第5部分:萃取法(又称穿孔法)

This part of ISO 12460 specifies an extraction method known as the “perforator method”. It is used for the determination of the formaldehyde content of unlaminated and uncoated wood-based panels.

Wood-based panels - Determination of formaldehyde release - Part 5: Extraction method (called the perforator method)

EN 16718:2015 木材和木材为基础的产品.木材和木制品中有机碳(TOC)的总用量

This European Standard describes a method for determining total organic carbon by calculating the difference between the results of measurements of total carbon (TC) and total inorganic carbon (TIC). The identification of the bio-based content given by the stable isotopes such as 13C is described also. This method is applicable to all wood species, wood-based materials (panels, plywood, wood-polymer, etc.) and woods containing chemicals in general.

Wood and wood based products - Dosage of the total organic carbon (TOC) in wood and wood based products

EN ISO 12460-3:2015 人造板.甲醛释放量的测定.第3部分:气体分析法(ISO 12460-3:2015)

Dieser Teil von ISO 12460 legt ein Verfahren zur Bestimmung der beschleunigten Formaldehydabgabe von beschichteten und unbeschichteten Holzwerkstoffen fest. Das Verfahren ist auch zur Prüfung anderer Werkstoffe (z. B. Kantenstreifen, Fußbodenbeläge, Schäume, Folien, schichtverklebte Holzprodukte, furnierte Holzprodukte, beschichtete Holzprodukte) geeignet.

Wood-based panels - Determination of formaldehyde release - Part 3: Gas analysis method