81.040.30 玻璃产品 标准查询与下载

T/GDFPT 0024-2021 米酒玻璃瓶质量要求

本文件规定了米酒玻璃瓶的要求、试验方法、检验规则、标志、包装、运输和贮存等质量要求。 本文件适用于盛装米酒的玻璃瓶。

Quality requirements for rice wine glass bottle

GOST 6799-2021 家具玻璃 一般技术条件

Glass articles for furniture. Specifications

GOST 21836-2021 工业装置用观察窗 技术条件

Sight glasses for industrial units. Specifications

KS L 2014-2020 太阳能反射玻璃

Solar reflective glass

KS L 2403-2020 水晶玻璃

Crystal glass

KS L 2408-2020 玻璃杯

Glass tumblers

T/WQS 002-2020 玻璃花瓶

3　要求 3.1　尺寸 尺寸偏差应符合表1规定。 表1　尺寸偏差 项目　外口径　底径　底厚　高度　壁厚 偏差（mm）　±2　±2　±2　±1.5　±0.5 3.2　外观 外观质量应符合表2规定。 表2　外观 缺陷名称　规  定　指 标 气泡　长度大于或等于5mm　不应有 　长度大于或等于3mm且小于5mm　允许1个 　长度大于或等于1mm且小于3mm　不多于3个 　长度小于1mm的密集气泡在任何一平方厘米范围内　不多于3个 杂粒　长度大于1mm　不许有 　长度大于或等于1mm且小于3mm　不多于2处 　长度小于1mm在任何一平方厘米范围内　不多于3处 表2  外观（续） 缺陷名称　规  定　指 标 崩口　明显的，刺手的　不许有 毛刺、毛边　毛刺，毛边刺手的　不许有 变形　口部明显的变形，影响外观的　不许有 　瓶身明显凹陷，影响外观的　不许有 　凸底，摆放摇摆的　不许有 炸裂　长度大于5mm穿透性的　不许有 纹路　长度大于50mm的　不许有 　长度在20mm和50mm之间的　不多于2条 表面光洁度　明显的模具氧化斑、油斑　不许有 　去不掉的粘料　不许有 3.3　理化性能 理化性能应符合表3规定 表3　理化性能 项目　规定 耐水性　符合GB/T6582-HGB3级 应力　小于或等于4级 抗冲击力　20g钢球30cm自由落体不破裂 稳定性　最大倾斜角8°，不发生倾倒

glass vase

T/FZWLW 18-2020 抗菌玻璃

本标准规定了抗菌玻璃的一般要求、抗菌性能要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于采用离子交换工艺的抗菌玻璃生产、检测和验收。

Antimicrobial glass

T/CSTM 00190-2020 金属和微晶玻璃复合衬板

本文件规定了金属和微晶玻璃复合衬板的术语与定义、要求、检验方法、检验规则、标志、包装、运输与贮存。 本文件适用于煤炭、矿石、工业原料等贮存仓和滑道内壁用的消失模法生产的金属和微晶玻璃复合衬板。

Composite lining plate used metal and glassceramic

ASTM D116-86(2020) 用于电气应用的玻璃化陶瓷材料的标准测试方法

1.1 These test methods outline procedures for testing samples of vitrified ceramic materials that are to be used as electrical insulation. Where specified limits are mentioned herein, they shall not be interpreted as specification limits for completed insulators. 1.2 These test methods are intended to apply to unglazed specimens, but they may be equally suited for testing glazed specimens. The report section shall indicate whether glazed or unglazed specimens were tested. 1.3 The test methods appear as follows: Section Test Method Related Standard(s) 6 Compressive Strength C773 13 Dielectric Strength D618, D149 8 Elastic Properties C623 15 Electrical Resistivity D618, D257, D1829 7 Flexural Strength C674, F417 9 Hardness C730, E18 5 Porosity C373 14 Relative Permittivity and Dissipation Factor D150, D2149, D2520 4 Specific Gravity C20, C329, F77 10 Thermal Conductivity C177, C408 12 Thermal Expansion C539, E288 11 Thermal Shock Resistance 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 11.3, 13.5, and 15.3. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications

T/ZBH 017-2020 晶硅光伏组件用材料 第1部分：面板玻璃

本标准规定了晶硅光伏组件用面板玻璃的术语和定义、分类、要求、试验方法、检验规则、包装、标志、运输、贮存等。 本标准适用于晶硅光伏组件用面板玻璃。

Materials for Crystalline Silicon Photovoltaic Modules Part 1 : Front cover Glass

T/ZBH 018-2020 晶硅光伏组件用材料 第2部分：背板玻璃

本标准规定了晶硅光伏组件用背板玻璃的术语和定义、分类、要求、试验方法、检验规则、包装、标志、运输、贮存。 本标准适用于晶硅光伏组件用背板玻璃。

Materials for Crystalline Silicon Photovoltaic Modules Part 2 : Rear Cover Glass

T/ZZB 1700-2020 展示柜用透明液晶显示中空玻璃门

本标准规定了展示柜用透明液晶显示中空玻璃门的术语和定义、基本要求、技术要求、试验方法、检验规则、包装、标志、运输与贮存、质量承诺。 本标准适用于商业展示柜的透明液晶显示中空玻璃门。

Transparent LCD insulating glass door for display case

ASTM C149-14(2020) 玻璃容器的耐热冲击性的标准测试方法

1.1 This test method covers the determination of the relative resistance of commercial glass containers (bottles and jars) to thermal shock and is intended to apply to all types of glass containers that are required to withstand sudden temperature changes (thermal shock) in service such as in washing, pasteurization, or hot pack processes, or in being transferred from a warm to a colder medium or vice versa. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thermal Shock Resistance of Glass Containers

T/QXBQ 0016-2020 人工吹制玻璃杯

本标准规定了人工吹制玻璃杯的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

hand blown glass

T/QXBQ 0005-2020 玻璃果汁罐

本标准规定了玻璃果汁罐的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

glass juice jar

T/QXBQ 0006-2020 玻璃蜡烛台

本标准规定了玻璃蜡烛台的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

glass candle holder

T/QXBQ 0009-2020 玻璃沙滩杯

本标准规定了玻璃沙滩杯的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

glass beach cup

T/QXBQ 0004-2020 玻璃分酒器

本标准规定了玻璃分酒器的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

glass wine dispenser

T/QXBQ 0012-2020 带柄玻璃杯

本标准规定了带柄玻璃杯的术语和定义、要求、试验方法、检验规则和标志、包装、运输、贮存。

Stem Glass