A52 长度计量 标准查询与下载

JJG 2054-2015 振动计量器具检定系统表

本检定系统表适用于振动计量器具的量值传递，规定了振动国家基准的组成和用途，由国家基准通过计量标准器具向工作计量器具传递振动量值的程序，并给出相应的扩展不确定度和基本检定方法等。在开展校准时，本检定系统表也可作为量值溯源的依据。 本检定系统表以振动频率f（Hz），振动加速度a（m/s）、速度v（m/s）、位移d（m）的幅值和相位φ（°）作为描述振动运动的主要物理量。

Verification Scheme of Measuring Instruments for Vibration

BS EN ISO 14638:2015 几何产品规范 (GPS). 矩阵模型

Geometrical product specifications (GPS). Matrix model

KS B ISO 10385-1:2014 封闭管道中水流量的测量.热水表.第1部分:规范

Measurement of water flow in closed conduits-Meters for hot water-Part 1:Specifications

JJF 1484-2014 湿膜厚度测量规校准规范

本规范适用于测量范围为(0~3 000) μm的湿膜厚度测量规的校准。

Calibration Specification for Wet Film Thickness Gauges

KS B ISO 13385-1:2014 产品几何技术规范(GPS).尺寸测量设备.第1部分:卡尺.设计和计量特性

이 표준은 캘리퍼스의 가장 중요한 설계 및 계량 특성에 대하여 규정한다.― 아날로그 지시가 있는 경우: 버니어 눈금 또는 원주상 눈금(다이얼)― 디지털 지시가 있는 경우: 디지털 디스플레이?

Geometrical product specifications(GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological characteristics

KS B ISO 463:2014 读数为0.01mm、0.001英寸和0.0001英寸的千分表

이 표준은 기계식 다이얼 게이지의 가장 중요한 설계와 계측 특성에 대하여 규정한다.

Geometrical Product Specifications(GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges

JJF 1454-2014 数字抖动仪校准规范

本校准规范适用于标准倍速和多倍速的数字式抖动仪(以下简称“抖动仪”)的校准。指针式抖动仪的校准可参照本校准规范。

Calibration Specification for Digital Jitter Meter

JJF 1453-2014 角运动传感器(角冲击绝对法)校准规范

本规范适用于采用角冲击激励方式对角运动传感器(包括角加速度、角速度和角位移传感器)在角加速度500°/s~15 000°/s (脉宽5 ms~30 ms)、角速度5°/s~600°/s(脉宽20 ms~100 ms)、角位移0 5°~100° (脉宽30 ms~150 ms)范围内的校准。

Calibration Specification for Angular Motion Transducers (Primary Angular Shock)

JJF 1451-2014 轻便三杯风向风速表型式评价大纲

本型式评价大纲适用于机械式的轻便三杯风向风速表(以下简称三杯风表)的型式评价。

Program of Pattern Evaluation of Portable 3-cup Anemometer

DB23/T 1542-2014 精密单轴气浮轴角测量转台技术基本要求

Basic technical requirements of precise single-axis air bearing axis angle measurement turntable

DB23/T 1545-2014 超精密气浮主轴技术要求

Ultra-precision air bearing spindle technical requirements

DB23/T 1541-2014 高速气浮电主轴技术基本要求

Basic requirements for high-speed air-floating electric spindle technology

DB23/T 1543-2014 精密多轴气浮轴角测量转台技术基本要求

Technical basic requirements for precision multi-axis air bearing axis angle measurement turntable

DB23/T 1544-2014 超精密气浮导轨技术要求

Ultra-precision air bearing technical requirements

ASME B89.7.2-2014 尺寸测量规划

The objective of this Standard is to ensure correctness and acceptability of dimensional measurements. This Standard specifies requirements for preparation and approval of dimensional measurement plans and for the use of approved plans in making dimensional measurements. This Standard considers that a dimensional measurement method is acceptable if its associated measurement uncertainty per the Guide to the Expression of Uncertainty in Measurement (GUM) meets business needs, e.g., cost of measurements, consequences of pass and fail errors, liability, specific policies, and customer requirements. In assessing the acceptability of a stated measuring procedure, management should take into account the importance and difficulty of evaluating measurement uncertainty in such a way as to quantitatively capture the effects of all significant sources of measurement error.

Dimensional Measurement Planning

JJF(纺织) 012-2013 摇黑板机校准规范

本校准规范规定了摇黑板机的校准方法，适用于新制造、使用中和修理后的Y381、Y381A、YG381型摇黑板机的校准，其他型号的摇黑板机及不同规格黑板可参照执行。

Calibration Specification for the Winding Black Board Tester

DB23/T 1524-2013 大深径比微小孔径测量仪技术规程

Technical regulations for small aperture measuring instruments with large depth-to-diameter ratio

DB23/T 1526-2013 光学气浮隔微振平台技术基本要求

Basic requirements for optical air-flotation isolation micro-vibration platform technology

DB23/T 1528-2013 快速动态双频激光干涉仪技术规程

Technical regulations for fast dynamic dual-frequency laser interferometer

JJF 1423-2013 π尺校准规范

本规范适用于分度值为0.01mm, 0.02mm, 0.05mm,直径测量范围为9mm~16m的π尺的校准。

Calibration Specification for Pi Tapes