共找到 628 条与 长度计量 相关的标准,共 42 页
本规程适用于分度值/分辨力为O.Olmm,测量范围上限大于10mm,小于等于100mm的指针式或数显式大量程百分表的首次检定、后续检定和使用中检验。
Verification Regulation of Wide Range Dauges Reading in 0.01mm
本规范适用于钢筋保护层厚度测量仪和楼板厚度测量仪的校准。
Calibration Specification for Reinforced Concrete Covermeter and Floorslab Thickness Tester
本规程适用于测量下限大于或等于600mm,测量上限小于或等于4500mm的各种规格套管尺的首次检定、后续检定和使用中检验。
Verification Regulation of Casing Coupling Meter
本规范适用于光电测距仪、全站仪长度基线场和全球定位系统(GPS)接收机长度基线场的校准和周期内核查。
Calibration Specification for Baseline and Basenet
本规程适用于方形角尺首次检定、后续检定和使用中检验。
Verification Regulation of Square Gauge
이 표준은 다른 방향의 경로를 따라 전파하는 사운드의 속도에 대해 역시간을 적용하는 음파
Meteorology-Sonic anemometers/thermometers-Acceptance test methods for mean wind measurements
本规范适用于钢、硬质合金、陶瓷等材料制造的各类针规、三针的校准。
Calibration Specification for Cylindrica Measuring Pin
本规程适用于分度值为0.01mm、0.002mm,量程不大于10mm的指针式指示表:分度值为0.001mm,量程不大于5mm的指针式指示表;分辨力为0.01mm、0.005mm、0.001mm,量程不大于10mm的数显示指示表的首次检定、后续检定和使用中检验。
Verification Regulation of Dial Gauges (dial and digital)
本规程适用于分辨力不大于0.5μm,量程不大于50mm的数显式指示类量具检定仪和分度值不大于10μm,量程不大于25mm的机械式指示类量具检定仪的首次检定、 后续检定和使用中检验。
Verification Regulation of Tester for Dial Indicator Gauges
本规范适用于相对法自动和半自动齿轮齿距测量仪的校准。
Calibration Specification for Gear Pitch Measuring Instruments
This International Standard specifies the most important design and metrological characteristics of mechanical dial gauges.
Geometrical product specifications (GPS) - Dimensional measuring equipment - Design and metrological characteristics of mechanical dial gauges
本规程适用于分度值为0.Olmm,测量上限至500mm的外径千分尺;测量上限至25mm的板厚、壁厚千分尺;以及分辨力为0.OOlmm,0.0001mm,测量上限至500mm的数显外径千分尺的首次检定、后续检定和使用中检验。
Verification Regulation of Micrometer
本规范适用于测长仪的校准。
Calibration Specification for Length Measuring Instrument
本检定规程规定了标准球、标准半球(以下简称:标准(半)球)的检定技术要求、检定条件、检定项目、检定方法、鉴定结果处理和检定周期。 本检定规程适用于新制造、使用中和修理后的标准(半)球的检定。
Verification regulation for standard sphere and standard hemisphere
Geometrical product specifications (GPS) - Squares 90° - Part 2: Granite squares 90°
Geometrical product specifications (GPS) - Straight edges - Part 3: Granite straight edges; dimensions, technical delivery conditions
Basic norms of interchangeability. Geometrical product specifications. Positional tolerancing
Basic norms of interchangeability. Geometrical product specifications. Maximum material requirement, least material requirement and reciprocity requirement
This is the first Addenda to be published to ASME MFC-3M–2004.Following approval by the ASME MFC Standards Committee and ASME, and after public review,MFC-3Ma–2007 was approved by the American National Standards Institute on October11, 2007.Addenda to the 2004 edition of ASME MFC-3M–2004 are issued in the form of replacement pages.Revisions, additions, and deletions are incorporated directly into the affected pages. It is advisable,however, that this page, the Addenda title and copyright pages, and all replaced pages beretained for reference.
Addenda to ASME MFC-3M-2004 Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号