D92 采掘设备 标准查询与下载

MT/T 1003.1-2006 滚筒采煤机.大修规范.第1部分：总则和整机部分

MT/T 1003的本部分规定了滚筒采煤机大修的总则和整机部分的要求、试验方法和验收。 本部分适用于需要大修的滚筒采煤机（以下简称采煤机）。

Shearer-Specification of overhaul.Part 1:General principles and whole the machine

JB/T 8435-2006 气动盘式制动器

本标准规定了气动盘式制动器的型式、基本参数、技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本标准适用于气动盘式制动器（以下简称制动器）。本制动器可用于矿山、冶金、工程和船舶等机械设备。

Pneumatic disk brake

MT/T 971-2005 悬臂式掘进机　电气控制设备

本标准规定了煤矿用悬臂式掘进机电气控制设备（以下简称电控设备）的形式与参数、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于在含有瓦斯（甲烷）和粉尘爆炸危险的矿井中，作为开拓准备工作面悬臂式掘进机的控制设备。

Boom-type roadheader--Electric control equipment

ASTM D4702-06 机械钻煤取样系统的质量管理标准实施

1.1 This practice is applicable to cross-belt, falling stream, and auger sampling systems.1.2 Spacing of increments pertains to the kind of interval between increments. Intervals can be defined in quantitative terms, such as units of time or mass, or in terms of position over the lot.1.2.1 Spacing of Increments for Cross-Belt and Falling Stream SamplersCross-belt and falling stream type mechanical sampling systems take increments based on time, either at fixed time intervals or at random times during a fixed time strata. Some falling stream samplers can take increments based on equal mass of coal sampled as determined by scales. The sections of this practice that pertain to cross-belt and falling stream samplers describe procedures for only time-based sampling systems. This time-based inspection guideline will satisfy most criteria for mass-based or combination mass-based and time-based sampling systems. If there are items that are not covered, the inspector should refer to the manufacturer's literature.1.2.2 Spacing of Increments for Auger SamplingThe spacing of increments collected by auger sampling systems is defined in terms of position over the lot.1.3 It is essential that the inspector have the documentation listed in Section of this practice when conducting an inspection.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 5.

Standard Practice for Quality Management of Mechanical Coal Sampling Systems

MT/T 928-2004 悬臂式掘进机.圆环刮板链及驱动链轮的系列与参数

本标准规定了悬臂式掘进机用圆环刮板链(以下简称刮板链)及驱动链轮(以下简称链轮)的型式和参数系列。 本标准适用于煤矿井下用悬臂式掘进机，也适用于装煤机及连续采煤机等其他煤矿机械用圆环刮板链和链轮。

Boom-type roadheader-Series and parameters of scraper round link chain and driving sprocket

DIN 22261-1:2004 褐煤露天矿中的挖掘机、抛煤机和附属装置.第1部分:建造、投产和监测

Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 1: Construction, commissioning and monitoring

JB/T 5501-2004 地下铲运机 试验方法

　　本标准规定了地下铲运机的试验准备要求、整机性能试验方法、工业性试验方法、样机解体检查及其试验报告内容。 　　本标准适用于地下铲运机的型式试验、出厂试验及工业性试验。

Underground L.H.D - Test method

JB/T 6122-2004 破岩滚刀

本标准规定了破岩滚刀的型式、基本参数、技术要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于竖井钻机、工程钻机及隧道掘进机用滚刀。该滚刀主要用于钻凿矿山、军工、桥梁、水电站、港口、地质和城建等工程中的竖井、基桩孔及隧道。

Shaft drilling cutters

JB/T 5500-2004 地下铲运机

本标准规定了地下铲运机的术语定义、产品分类、技术要求、检验规则、标志、包装、运输和贮存。 本标准适用于地下电动铲运机和地下内燃铲运机。

Underground L.H.D

JB/T 10412-2004 XN(W)型高压水射流钢管清洗机

本标准规定了XN（W）型高压水射流钢管清洗机的型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 　　本标准适用于额定排出压力为50MPa～100MPa、额定输出功率为45kW～110kW的清洗机。该清洗机采用高压水射流清洗的方式用于清洗矿山、油田使用后的钢管内、外壁上粘结物，达到清洗钢管的目的，以满足生产再使用的要求。同时也可以用于清洗油田内、外壁上结蜡、原油油污、砂土厚度小于15mm的油管、水管。

XN (W) High pressure water jet steel- pipe line cleaning equipment

JB/T 5503-2004 立爪挖掘装载机

　　本标准规定了立爪装载机和地下挖掘装载机的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 　　本标准适用于立爪装载机和地下挖掘装载机。

Excavating digging arm loader

JB/T 9027-2004 固定车箱式窄轨矿车 技术条件

本标准规定了固定车箱式窄轨矿车的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于GB/T 2885.1中规定的固定车箱式矿车。

Technical conditions for fixed-carriage narrow-gauge mine cars

ASTM D4916-04 机械钻抽样的标准实施规范

1.1 This practice describes procedures for the collection of an increment, partial sample, or gross sample of material using mechanical augers. Reduction and division of the material by mechanical equipment at the auger is also covered. Further manual or mechanical reduction or division of the material elsewhere shall be performed in accordance with Method D 2013.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Mechanical Auger Sampling

YS/T 460-2003 高气压环形潜孔钻机

High-pressure ring in-the-hole drill rigs

NF E56-005-2:2003 地下采矿机械.地下作业用移动机械.安全性.第2部分:轨道机车

Machines for underground mines - Mobile machines working underground - Safety - Part 2 : rail locomotives.

DIN EN 1552:2003 地下采矿机械.工作面上的移动式采掘机械.割剪机、装载机和刮板系统的安全要求

This standard specifies safety requirements for shearer loaders and ploughs working underground including their control systems and guiding and haulage elements. The machines work with tools for cutting minerals. They are guided on armoured scraper conveyors or attachments and either have built-in haulage systems or are separately hauled. They may be equipped with loading devices, operated by an attending person or driver or remotely or program controlled. It does not cover any hazards resulting from the electrical equipment. It does not contain any requirements relating to dust suppression or firedamp hazards.#,,#

Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems; German version EN 1552:2003

BS EN 1552:2003 地下采矿机械.工作面上的移动式采掘机械.截装机和开沟机系统的安全要求

1 This European Standard specifies safety requirements which shall be met to minimize the hazards listed in clause 4 that may occur during the assembly, use, maintenance, repair, decommissioning, disassembly and disposal of shearer loaders and plough systems when operated in accordance with the manufacturer's requirements in underground mining. The machines work with tools for cutting minerals such as coal, ore, salt and surrounding rock, at a fixed or variable height and are guided on armoured face conveyors or their attachments. Shearer loaders have built-in haulage systems. They may be directly operated by one or more drivers or be remotely or program controlled. Plough systems are remotely controlled. Wireless remote control systems of shearer loaders are used in the immediate environment of the machines. 2 This European Standard does not cover any hazards resulting from the electrical equipment associated with the machine. It does not contain any requirements relating to dust suppression or firedamp hazards. . Hazards due to noise are also excluded from this standard, but a separate standard is in preparation where hazards due to noise will be addressed. NOTE Only a small amount of the noise emitted at the point of use of shearer loaders and plough systems is generated by the machines themselves. The noise level is affected more by the breaking mineral and the conveyors. Dust is generated not only by the mode of operation of the machines, but also by the material to be extracted, the environment, the roof support and the conveyor. For example, equipping the machine with a water spray may not completely eliminate the hazard on its own. It does not cover face conveyors, spill plates and auxiliary devices such as lasers etc. It is intended for manufacturers producing and marketing complete machines, and for manufacturers assembling machines or parts of machines from different origins or assembling machines for their own use. These are called "manufacturers" in this European Standard. 3 This document is not applicable to machines that are manufactured before the date of publication of this European Standard by CEN.

Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems

BS EN 1889-1:2003 地下采矿机械.移动式机械地下作业.安全性.安装橡胶轮胎的运载工具

1 This European Standard specifies the safety requirements and tests for self-propelled rubber tyred vehicles (defined in clause 3) intended primarily for use in underground mining (i.e. mine vehicles) and other underground workings (e.g. tunnelling vehicles). The electrical supply voltage is limited to 1100 A.C. and 1500 D.C. 2 This European Standard deals with the technical requirements to minimise the hazards listed in clause 4 which can arise during the commissioning, the travelling operation and the maintenance of rubber tyred vehicles when carried out in accordance with the specifications given by the manufacturer or his authorized representative. 3 This European Standard does not include rubber tyred drilling rigs, which-are covered by EN 791, or earth moving machinery not intended primarily for use in underground mines, which are covered by EN 474 series. This European Standard does not take account of specific hazards associated with special-purpose vehicles, e.g. tankers, explosives vehicles. This European Standard does not address operation in potentially explosive atmospheres, which is covered by another European Standard. Hazards due to noise are excluded from this standard, but a separate standard is in preparation where hazards due to noise will be addressed. This European Standard does not address remote control or deal with radiation and vibration. It does not deal with any equipment installed on the vehicle for purposes other than travelling. 4 This European Standard applies to vehicles which are manufactured after the date of issue of this standard.

Machines for underground mines - Mobile machines working underground - Safety - Rubber tyred vehicles

BS EN 1889-2:2003 地下采矿机械.移动式机械地下作业.安全.轨式机车

1 This European standard specifies the safety requirements and tests for rail locomotives for use in underground mining (i.e. mine locomotives) and other underground workings (e.g. tunnelling locomotives). 2 This European standard deals with the technical requirements to minimise the hazards listed in clause 4 which can arise during the commissioning, the operation and the maintenance of locomotives when carried out in accordance with the specifications given by the manufacturer or his authorised representative. This European standard does not address the special hazards associated with the rack drive of rack and pinion locomotives. 3 This European standard does not deal with radiation and vibration. It does not address remote control locomotives or operation in potentially explosive atmospheres. Hazards due to noise are excluded from this standard, but a separate standard is in preparation where hazards due to noise will be addressed.1.4 This European standard applies to locomotives which are manufactured after the date of issue of this standard.

Machines for underground mines - Mobile machines working underground - Safety - Rail locomotives

NF E56-001:2003 地下采矿机械.工作面上的移动式采掘机械.截装机和开沟系统的安全性要求

Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems.