E94 海洋石油作业用设备 标准查询与下载

SY/T 7057-2016 动态立管

dynamic riser

SY/T 7064.5-2016 石油天然气工业 海洋结构物特殊要求 第5部分：设计和施工过程中的重量控制

Special requirements for offshore structures in the oil and gas industry Part 5: Weight control during design and construction

SY/T 7054-2016 海底管道维修推荐作法

Recommended Practices for Subsea Pipeline Maintenance

ISO 19905-1:2016 石油和天然气工业. 海上移动装置的现场具体评定. 第1部分: 自升式钻塔

This part of ISO 19905 specifies requirements and guidance for the site‐specific assessment of independent leg ‐up unit ses: jack s for use in the petroleum and natural gas industries. It addres cuated and unmanned jack‐ups; a) manned non‐evacuated, manned eva b) the installed phase at a specific site. To ensure acceptable reliability, the provisions of this part of ISO 19905 form an integrated approach, which is used in its entirety for the site‐specific assessment of a jack‐up. This part of ISO 19905 does not apply specifically to mobile offshore drilling units operating in regions subject to sea ice and icebergs. When assessing a jack‐up operating in such areas, it is intended that the assessor supplement the provisions of this part of ISO 19905 with the provisions relating to ice actions and procedures for ice management contained in ISO 19906. This part of ISO 19905 does not address design, transportation to and from site, or installation and removal from site. However, it is advisable that the assumptions used in the assessment be checked against the as‐installed configuration. To ensure that the design of the jack‐up is sound and the structure is adequately maintained, this part of  hold a valid classification society certification from a recognized classification society (RCS) throughout the te s sment duration of the operation at the specific si ubject to asses ; or  have been verified by an independent competent body to be structurally fit for purpose for elevated ati situ ons and are subject to periodic inspection, both to the standards of an RCS. NOTE 1 An RCS is an International Association of Classification Societies (IACS) member body, meeting the RCS definition given in 3.52. Jack‐ups that do not comply with this requirement are assessed according to the provisions of ISO 19902, supplemented by methodologies from this part of ISO 19905, where applicable. NOTE 2 Future revisions of this part of ISO 19905 can be expanded to cover mat‐supported jack‐ups. NOTE 3 Well conductors are a safety‐critical element for jack‐up operations. However, the integrity of well conductors is not part of the site‐specific assessment process for jack‐ups and is, therefore, not addressed in this part of ISO 19905. Annex A provides references to other publications addressing this topic. NOTE 4 RCS rules and the IMO MODU code provide guidance for the design of jack‐ups.

Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups

NF M87-264-8*NF EN ISO 19901-8:2015 石油和天然气工业. 海上结构的特殊要求. 第8部分: 海洋土壤调查

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 8 : marine soil investigations

BS EN ISO 19901-1:2015 石油和天然气工业 海上结构的具体要求 Metocean 设计和操作注意事项

Petroleum and natural gas industries. Specific requirements for offshore structures. Metocean design and operating considerations

ISO 19901-1:2015 石油和天然气工业.海上建筑物的特殊要求.第1部分:Metocean设计和运行研究

This part of ISO 19901 gives general requirements for the determination and use of meteorological and oceanographic (metocean) conditions for the design, construction and operation of offshore structures of all types used in the petroleum and natural gas industries. The requirements are divided into two broad types: — those that relate to the determination of environmental conditions in general, together with the metocean parameters that are required to adequately describe them; — those that relate to the characterization and use of metocean parameters for the design, the construction activities or the operation of offshore structures. The environmental conditions and metocean parameters discussed are: — extreme and abnormal values of metocean parameters that recur with given return periods that are considerably longer than the design service life of the structure, — long-term distributions of metocean parameters, in the form of cumulative, conditional, marginal or joint statistics of metocean parameters, and — normal environmental conditions that are expected to occur frequently during the design service life of the structure. Metocean parameters are applicable to: — the determination of actions for the design of new structures, — the determination of actions for the assessment of existing structures, — the site-specific assessment of mobile offshore units, — the determination of limiting environmental conditions, weather windows, actions and action effects for pre-service and post-service situations (i.e. fabrication, transportation and installation or decommissioning and removal of a structure), and — the operation of the platform, where appropriate. NOTE Specific metocean requirements for site-specific assessment of jack-ups are contained in ISO 19905-1, for arctic offshore structures in ISO 19906 and for topside structures in ISO 19901-3.

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations

BS EN ISO 19901-8:2015 石油和天然气工业. 海上构筑物的特殊要求. 海洋土壤调查

Petroleum and natural gas industries. Specific requirements for offshore structures. Marine soil investigations

BS IEC 61892-1:2015 移动式及固定式海上设施.电气装置.一般要求和条件

Mobile and fixed offshore units. Electrical installations. General requirements and conditions

DIN EN ISO 19901-3:2015 石油和天然气工业 海上构筑物的特定要求 第3部分：最上层构筑物(ISO 19901-3-2014) 英文版本EN ISO 19901-3-2014

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2014); English version EN ISO 19901-3:2014, only on CD-ROM

BS EN ISO 19901-3:2014 石油和天然气工业.海上建筑物的专门要求.水线以上部分结构

Petroleum and natural gas industries. Specific requirements for offshore structures. Topsides structure

KS B ISO 19901-7:2014 石油和天然气工业.海洋结构的特殊要求.第7部分:浮式海上建筑物和移动式海上设备用保持系统

Petroleum and natural gas industries — Specific requirements for offshore structures — Part 7: Stationkeeping systems for floating offshore structure and mobile offshore units

ISO 19901-3:2014 石油和天然气工业.海上建筑物的具体要求.第3部分:水线以上部分结构

This part of ISO 19901 gives requirements for the design, fabrication, installation, modification and structural integrity management for the topsides structure for an oil and gas platform. It complements forms of support structure. Requirements in this part of ISO 19901 concerning modifications and maintenance relate only to those aspects that are of direct relevance to the structural integrity of the topsides structure. The actions on (structural components of) the topsides structure are derived from this part of The resistances of structural components of the topsides structure can be determined by the use of international or national building codes, as specified in this part of ISO 19901. If any part of the topsides structure forms part of the primary structure of the overall structural system of the whole platform, the requirements of this part of ISO 19901 are supplemented with applicable requirements in ISO 19902, This part of ISO 19901 is applicable to the topsides of offshore structures for the petroleum and natural gas industries, as follows: — topsides of fixed offshore structures; — discrete structural units placed on the hull structures of floating offshore structures and mobile offshore units; — certain aspects of the topsides of arctic structures. This part of ISO 19901 is not applicable to those parts of the superstructure of floating structures that form part of the overall structural system of the floating structure; these parts come under the provisions of ISO 19904-1. This part of ISO 19901 only applies to the structure of modules on a floating structure that do not contribute to the overall integrity of the floating structural system. This part of ISO 19901 is not applicable to the structure of hulls of mobile offshore units. This part of ISO 19901 does not apply to those parts of floating offshore structures and mobile offshore units that are governed by the rules of a recognized certifying authority and which are wholly within the class rules. Some aspects of this part of ISO 19901 are also applicable to those parts of the hulls of floating offshore structures and mobile offshore units that contain hydrocarbon processing, piping or storage. This part of ISO 19901 contains requirements for, and guidance and information on, the following aspects of topsides structures: — design, fabrication, installation and modification; — in-service inspection and structural integrity management; — assessment of existing topsides structures;  Licensee=University of Alberta/5966844001, User=ahmadi, rozita 1  — reuse; — decommissioning, removal and disposal; — prevention, control and assessment of fire, explosions and other accidental events. This part of ISO 19901 applies to structural components including the following: — primary and secondary structure in decks, module support frames and modules; — flare structures; — crane pedestal and other crane support arrangements; — helicopter landing decks (helidecks); — permanent bridges between separate offshore structures; — masts, towers and booms on offshore structures.

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure

EN ISO 19901-3:2014 石油和天然气工业.海上建筑物的专门要求.水线以上部分结构

Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2014)

IEC 61892-7:2014 移动式及固定式近海装置.电气装置.第7部分:危险区域

This part of IEC 61892 contains provisions for hazardous areas classification and choice of electrical installation in hazardous areas in mobile and fixed offshore units@ including pipelines@ pumping or 'pigging' stations@ compressor stations and exposed location single buoy moorings@ used in the offshore petroleum industry for drilling@ processing and for storage purposes. It applies to all installations@ whether permanent@ temporary@ transportable or hand-held@ to AC installations up to and including 35 000 V and DC installations up to and including 1 500 V. (AC and DC voltages are nominal values). This standard does not apply to electrical installations in rooms used for medical purposes@ or in tankers.

Mobile and fixed offshore units - Electrical installations - Part 7: Hazardous areas

BS IEC 61892-5:2014 移动和固定的近海工程装置.电气设备.移动装置

Mobile and fixed offshore units. Electrical installations. Mobile units

DIN CEN ISO/TR 19905-2:2014 石油和天然气工业 移动式海上设备的特地场地评定 第2部分：自升式说明和具体样品计算 (ISO/TR 19905-2-2012) 英文版本CEN ISO/TR 19905-2-2013

Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 2: Jack-ups commentary and detailed sample calculation (ISO/TR 19905-2:2012); English version CEN ISO/TR 19905-2:2013, only on CD-ROM

DIN EN ISO 19900:2014 石油和天然气工业.近海结构的一般要求(ISO 19900-2013).英文版本EN ISO 19900-2013

Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013); English version EN ISO 19900:2013

SY/T 6981-2014 暖风加热和空气调节系统的安装

本标准规定了包括过滤器、风管和相关设备在内的暖风加热和空气调节系统的制造、安装、运行和维修的原则,以保证当火灾或类似情况出现时,生命财产不受到火焰、烟气和燃气的损坏。本标准适用于为下列处所通风的所有系统:a)单用户或双用户居所。b)体积不超过708m (25000ft)的居所。c)高度超过三层的可燃结构建筑物,宜遵循NFPA 90A的规定。

Standard for the installation of warm air heating and air-conditioning systems

SY/T 6982-2014 通风空调系统的安装

简介风道系统具有把烟气、热气和火焰从一个区域传到另一个区域的潜在可能,也可能送空气到火灾区域以助燃。基于以上原因,风道系统的防火性对生命安全和财产保护是必要的。因此,具有完整防火性能的风道系统本身也可作为建筑物防火系统的一部分(见1.4)。适用范围本标准适用于以下建筑物中的所有通风系统:a)*容积超过707.9m (25000ft)的空间。b)*不考虑容积时,垂直高度超过3层的Ⅲ类、Ⅳ类和Ⅴ类建筑。c)*不包括其他适用的NFPA标准的建筑物和空间。d)*不包括其他适用的NFPA标准的居住者或进程。目的本标准规定了有关火灾中保护生命和财产安全的最低要求。这些要求为了达到下列目的:a)限制烟气通过风道在建筑物内扩散,或从外部进入建筑物内。b)控制火源从着火点(无论建筑物内或建筑物外)通过风道蔓延。c)维持建筑物结构及构件的耐火完整性。避免风道安装影响地板、隔壁、屋顶、墙壁和地板组合件或屋顶天花板组合件完整性。d)使风道系统的点火源和元件的可燃性减至最少。e)允许建筑物中的风道系统用于应急烟气控制。本标准并不限于新方法或新设计的使用。当使用新的方法和设计时,应将充足的技术数据提供给权威机构进行批准,这些技术数据应能够证明所提出的方法或设计在质量、强度、耐用性以及安全性上与规定的标准等同。本标准的规定没有追溯力。当一个系统修改、扩充或修复,本标准的要求应只适用于当前进行的部位。*烟气控制*维护(保留)

Standard for the installation of air-conditioning and ventilating systems