G52 涂料辅助材料 标准查询与下载

ISO 3262-22:2001 涂料用填充剂 规范和试验方法 第22部分：热碱处理的硅藻土

This part of ISO 3262 specifies requirements and corresponding methods of test for flux-calcined kieselguhr.

Extenders for paints - Specifications and methods of test - Part 22: Flux-calcined kieselguhr; German version EN ISO 3262-22:2001

ISO 3262-12:2001 涂料用填充剂 规范和试验方法 第12部分：白云母

This part of ISO 3262 specifies requirements and corresponding methods of test for muscovite-type mica.

Extenders for paints - Specifications and methods of test - Part 12: Muscovite-type mica

DIN EN ISO 3262-11:2001 涂料用填充剂.规范和试验方法.第11部分:含碳酸盐的片状天然滑石 (ISO 3262-11:2000); 德文版本 EN ISO 3262-11:2000

Extenders for paints - Specifications and methods of test - Part 11: Natural talc, in lamellar form, containing carbonates (ISO 3262-11:2000); German version EN ISO 3262-11:2000

DIN EN ISO 3262-10:2001 涂料用填充剂.规范和试验方法.第10部分:片状天然滑石/亚氯酸盐 (ISO 3262-10:2000); 德文版本 EN ISO 3262-10:2000

The document specifies requirements and corresponding test methods for natural talc/chlorite in lamellar form for use as extender in paints. For the composition (talc, chlorite and talc/chlorite contents), matter volatile at 105? loss on ignition, matter soluble in water and pH value figures are specified. Requirements for residue on sieve, particel size distribution, matter soluble in hydrochlorid acid, colour, lightness and resistivity of aqueous extract are left to an agreement between the interested parties.#,,#

Extenders for paints - Specifications and methods of test - Part 10: Natural talc/chlorite in lamellar form (ISO 3262-10:2000); German version EN ISO 3262-10:2000

BS 6782-17:2001 涂料用粘合剂.水稀释的粘合剂的MEQ值的测定

Binders for paints - Determination of MEQ value of water-dilutable binders

BS 6782-16:2001 涂料用粘合剂.水稀释粘合剂的通用试验方法

Binders for paints. General methods of test for water-dilutable binders

ASTM D2613-01(2012) EDTA法测定涂料催干剂中钙或锌的标准试验方法

1.1 This test method covers a titrimetric determination of calcium in liquid calcium driers and zinc in liquid zinc driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA). 1.2 This test method is not applicable to drier blends. 1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Calcium or Zinc in Paint Driers by EDTA Method

ASTM D1296-01(2012) 挥发性溶剂和烯释剂气味的标准试验方法

1.1 This test method covers a comparative procedure for observing the characteristic and residual odors of volatile organic solvents and diluents to determine their odor acceptability in a solvent system. 1.2 It is not intended that this test method be employed to determine subtle odor differences between materials or to determine odor intensity. 1.3 It is recommended that this test method not be employed to determine the residual odor of a liquid if its time for evaporation to dryness at room temperature exceeds 30 min or as agreed upon. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 4. 1.6 For specific hazard information, see the supplier's Material Safety Data Sheet (MSDS).

Standard Test Method for Odor of Volatile Solvents and Diluents

ASTM D1310-01 用泰格开口杯装置测定液体闪点和燃点的测试方法

1.1 This test method covers the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between 0 and 325176;F (-18 and 165176;C) and fire points up to 325176;F.1.2 This test method, when applied to paints and resin solutions that tend to skin over or that are very viscous, gives less reproducible results than when applied to solvents. Note 18212;In order to conserve time and sample, the fire point of a material may be determined by the Tag Open-Cup Method by continuing the heating of the specimen to its fire point. Fire points may also be determined by Test Method D 92, which should be used for fire points beyond the scope of this test method.1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end use.1.4 This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

ASTM D1310-01(2007) 用泰格开口杯装置测定液体闪点和燃点的测试方法

Flash point and fire point of a liquid are physical properties that may be used to define their flammability hazards. The flash point may be used to classify materials in government regulations.1.1 This test method covers the determination by Tag Open-Cup Apparatus of the flash point and fire point of liquids having flash points between 18 and 165176;C (0 and 325176;F) and fire points up to 325176;F.1.2 This test method, when applied to paints and resin solutions that tend to skin over or that are very viscous, gives less reproducible results than when applied to solvents. Note 1 - In order to conserve time and sample, the fire point of a material may be determined by the Tag Open-Cup Method by continuing the heating of the specimen to its fire point. Fire points may also be determined by Test Method D 92, which should be used for fire points beyond the scope of this test method.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end useThis standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

ASTM D2613-01(2017) 采用EDTA法测定漆干剂钙或锌含量的标准试验方法

4.1 This test method may be used to confirm the stated calcium or zinc content of pure liquid calcium or zinc driers soluble in toluene-alcohol and manufactured for use by the coatings industry. 1.1 This test method covers a titrimetric determination of calcium in liquid calcium driers and zinc in liquid zinc driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA). 1.2 This test method is not applicable to drier blends. 1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Calcium or Zinc in Paint Driers by EDTA Method

JIS K 5421:2000 熟油及熟亚麻籽油

この規格は，ボイル油 及び煮あまに油の品質とその試験方法について規定する。

Boiled oil and boiled linseed oil

DIN 55938:2000 色漆和清漆用粘合剂.精炼豆油.要求和试验方法

The document describes requirements and test methods for refined soya bean oil for application in paints, varnishes and similar coating materials.#,,#

Binders for paints and varnishes - Refined soya bean oil - Requirements and methods of test

DIN 55967:2000 色漆和清漆用原材料.甘油.要求和试验方法

Raw materials for paints and varnishes - Glycerine - Requirements and methods of test

CGSB 1.4-00-CAN/CGSB-2000 矿物油稀释剂.勘误表:2000年12月

La présente norme s’applique au diluant, essence minérale ou white spirit, produit de distillation du pétrole, convenant à une utilisation générale dans la dilution des peintures et des vernis. Ce produit ne doit pas être employé dans des applicati

Petroleum Spirits Thinner

BS EN ISO 3262-15:2000 涂料填充剂.规范和试验方法.透明石英

This part of ISO 3262 specifies requirements and corresponding methods of test for vitreous silica.

Extenders for paints - Specifications and methods of test - Vitreous silica

BS EN ISO 3262-19:2000 涂料填充剂.规范和试验方法.沉淀石英砂

This part of ISO 3262 specifies requirements and corresponding methods of test for precipitated silica.

Extenders for paints - Specifications and methods of test - Precipitated silica

BS EN ISO 3262-18:2000 涂料填充剂.规范和试验方法.沉淀硅铝酸钠

This part of ISO 3262 specifies requirements and corresponding methods of test for precipitated sodium aluminium silicate.

Extenders for paints - Specifications and methods of test - Precipitated sodium aluminium silicate

BS EN ISO 3262-10:2000 涂料填充剂.规范和试验方法.片状天然滑石/亚氯酸盐

This part of ISO 3262 specifies requirements and corresponding methods of test for products made from naturally occurring talc/chlorite in lamellar form. NOTE The mineralogical classes have been designated in accordance with products existing on the market (see annex A).

Extenders for paints - Specifications and methods of test - Natural talc/chlorite in lamellar form

BS EN ISO 3262-11:2000 涂料填充剂.规范和试验方法.含碳酸盐的片状天然滑石

This part of ISO 3262 specifies requirements and corresponding methods of test for products made from naturally occurring talc in lamellar form associated with carbonates. NOTE The mineralogical classes have been designated in accordance with products existing on the market (see annex A).

Extenders for paints - Specifications and methods of test - Natural talc, in lamellar form, containing carbonates