G52 涂料辅助材料 标准查询与下载

ISO 150:2006 色漆和清漆用生的、精制的和熟的亚麻仁油.规范和试验方法

This International Standard specifies the requirements and the corresponding methods of test for raw, refined and boiled linseed oils for paints and varnishes.

Raw, refined and boiled linseed oil for paints and varnishes - Specifications and methods of test

ASTM D3545-06(2012) 气相色谱法测定乙酸乙酯中乙醇含量和纯度的标准试验方法

1.1 This test method covers the determination by gas chromatography of the ester content and the corresponding alcohol content of acetate esters. This test method has been applied to ethyl, n-propyl, isopropyl, n-butyl, isobutyl, and 2-ethoxyethyl acetates. 1.2 Water, and in some cases acetic acid, cannot be determined by this test method and must be measured by other appropriate ASTM procedures and the results used to normalize the chromatographic value. 1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for material listed in this specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography

DIN 55940:2005 色漆和清漆用粘合剂.脱水蓖麻油.要求和试验方法

The document specifies requirements for dehydrated castor oil used in paints, varnishes and similar coating materials.#,,#

Binders for paints and varnishes - Dehydrated castor oil - Requirements and methods of test

DIN EN ISO 16805:2005 色漆和清漆用粘合剂.玻璃化转变温度的测定

Specification of a procedure for sample preparation for the determination of the glass transition temperature of binders for paints and varnishes, including coating powders, by differential colorimetry scanning (DSC).

Binders for paints and varnishes - Determination of glass transition temperature (ISO 16805:2003); German version EN ISO 16805:2005

WJ 9028-2005 涂料用硝化棉规范

本規範规定了涂料用硝化棉的要求、质量保证规定、交货准备等内容。 本规范适用于涂料用硝化棉的制造与验收。

Specification for nitrocellulose for paint

BS EN ISO 16805:2005 色漆和清漆用粘合剂.玻璃转变温度的测定

ISO 16805:2003 specifies the procedure to be used for sample preparation for the determination of the glass transition temperature of binders for paints and varnishes, including coating powders, by differential scanning calorimetry (DSC). The method to be used for determining the glass transition temperature is specified in ISO 11357-2.

Binders for paints and varnishes. Determination of glass transition temperature

BS EN ISO 4625-1:2005 涂料和清漆用粘合剂.软化点的测定.环-球法

This part of ISO 4625 specifies methods of determining the softening point of resins (including rosin) and similar materials by means of the ring-and-ball apparatus. Both manual and automatic methods are specified.

Binders for paint and varnishes - Determination of softening point - Ring-and-ball method

BS EN ISO 4625-2:2005 涂料和清漆用粘合剂.软化点的测定.环-球接合法

This part of ISO 4625 specifies a method for determining the softening point of resins (including rosin) by means of a cup-and-ball apparatus and can, under user-defined conditions, give results comparable to those obtained using the ring-and-ball method (ISO 4625-1).

Binders for paint and varnishes - Determination of softening point - Cup-and-ball method

ASTM D464-05(2010) 松脂油产品包括妥尔油及其相关产品的皂化值的标准试验方法

These test methods are designed to broaden the scope of the earlier editions of the test method by the inclusion of tall oil and tall oil derived products as test materials and is referenced in Test Methods D803. The saponification number is an important property of tall oil and the products obtained by the fractionation of tall oil. It is the test method widely used to determine the total acid content, both free and combined, of these products. The potentiometric test method should be used when the most reproducible results are required.1.1 These test methods cover the determination of the saponification number of tall oil and products obtained by the fractionation of tall oil such as rosin, fatty acids and distilled tall oil as defined in Terminology D804. These test methods are also applicable to gum and wood rosin. Two test methods are covered as follows: 1.1.1 Test method using a potentiometric method, and 1.1.2 Test method using an internal indicator method. 1.2 The potentiometric method is suitable for use with both light- and dark-colored test samples. It should be considered the referee method. The internal indicator method is suitable for use only with light- and medium-colored test samples. It should be considered the alternate method. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Saponification Number of Naval Store Products Including Tall Oil and Other Related Products

ASTM D3988-05 EDTA法测定涂料干燥剂中钒的标准试验方法

This test method may be used to confirm the stated content of a pure liquid vanadium drier manufactured for use by the coatings industry.1.1 This test method covers the titrimetric determination of vanadium in liquid vanadium driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).1.2 This test method is limited to the determination of the vanadium content of a liquid vanadium drier that does not contain other drier elements. This test method is not applicable to drier blends.1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.1.4 This test method has been tested for concentrations of 3 and 4 % vanadium, but there is no reason to believe that it is not suitable for higher or lower vanadium concentrations provided specimen size is adjusted proportionately.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Vanadium in Paint Driers by EDTA Method

ASTM D3970-05(2017) 采用氧化滴定法测定色漆干燥剂中铈含量的标准试验方法

4.1 This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry. 1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate. 1.2 This test method is not applicable to dryer blends. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

ASTM D3926-05(2011) 钛粉(二氧化钛)稀浆中固体百分比标准试验方法

These test methods are intended as a quick and reliable procedure for measuring the titanium dioxide pigment content of aqueous slurries. Included with the pigment content in the percent solids are the various nonvolatile additives used in preparing a stable slurry. Because the aluminum and silica oxide treatments on the more highly treated titanium dioxide pigments may change somewhat with prolonged drying, in the oven method the solids of the slurry are considered dry after heating at 105°C for 60 to 65 min. The high temperature associated with the infrared moisture analyzer may also effect a change in the aluminum and silica oxide treatment on highly treated TiO2 products. Therefore, care in selection of time and temperature are critical to obtain accurate results with the infrared method. With the short duration of test associated with the microwave drying system, overdrying is not a concern.1.1 These test methods cover the determination of the weight percent of solids in aqueous slurries of titanium dioxide pigments by either the use of a gravity-convection oven (Method A), infrared radiation moisture analyzer (Method B), or a microwave drying system (Method C). 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This test standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Percent Solids in Titanium Dioxide Slurries

ASTM D2373-05(2011) 用EDTA法测定涂料干燥剂中钴含量的标准试验方法

The amount of cobalt drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated cobalt content of a pure liquid cobalt drier soluble in glacial acetic acid and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of cobalt in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA). 1.2 This test method is not applicable to drier blends. If driers other than cobalt are present, they may interfere by reacting with EDTA under the conditions used for analysis. 1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Cobalt in Paint Driers by EDTA Method

ASTM D2374-05(2011) EDTA法测定涂料干燥剂中铅含量的标准试验方法

The amount of lead drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated lead content of pure liquid lead drier soluble in glacial acetic acid and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of lead in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA). 1.2 This test method is not applicable to drier blends. If driers other than cobalt are present, they may interfere by reacting with EDTA under the conditions used for analysis. 1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Lead in Paint Driers by EDTA Method

ASTM D3926-05 二氧化钛浆料中固体百分比的标准试验方法

These test methods are intended as a quick and reliable procedure for measuring the titanium dioxide pigment content of aqueous slurries. Included with the pigment content in the percent solids are the various nonvolatile additives used in preparing a stable slurry. Because the aluminum and silica oxide treatments on the more highly treated titanium dioxide pigments may change somewhat with prolonged drying, in the oven method the solids of the slurry are considered dry after heating at 105°C for 60 to 65 min. The high temperature associated with the infrared moisture analyzer may also effect a change in the aluminum and silica oxide treatment on highly treated TiO2 products. Therefore, care in selection of time and temperature are critical to obtain accurate results with the infrared method. With the short duration of test associated with the microwave drying system, overdrying is not a concern.1.1 These test methods cover the determination of the weight percent of solids in aqueous slurries of titanium dioxide pigments by either the use of a gravity-convection oven (Method A), infrared radiation moisture analyzer (Method B), or a microwave drying system (Method C).1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This test standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Percent Solids in Titanium Dioxide Slurries

ASTM D2375-05 用EDTA法测定涂料干燥剂中锰的标准试验方法

The amount of manganese drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated manganese content of pure liquid manganese drier soluble in toluene-alcohol and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of manganese in liquid paint driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).1.2 This test method is not applicable to drier blends.1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Manganese in Paint Driers by EDTA Method

ASTM D509-05(2011)e1 松香分级和抽样的标准试验方法

Rosin is an important product of the centuries old Naval Stores industry and is produced and consumed in many countries throughout the world. Consequently, reliable methods of sampling and grading rosin are necessary. The test methods based on the use of the USDA Official Standards described herein, were developed many years ago for the sampling and grading of rosin and are similar to those included in the Naval Stores Act. Although these test methods based on the use of the USDA Official Standards are still applicable, many additional test methods are now used to grade rosin. In particular, the color of rosin is now more commonly reported using the Gardner color scale rather than the USDA Official Standards. In addition, Test Methods E28, D465, and D5974 are widely used to assess the quality of rosin in addition to the color grading methods described in this standard.1.1 These test methods cover procedures for sampling and determining the grade of rosin delivered in commercial bags, barrels, drums or in molten form. Although developed for rosin, these methods can also be used for the grading of modified rosins and rosin based resins. Note 18212;All rosin sold in interstate commerce must be described by reference to the U. S. Standards for rosin, and is therefore subject to grading prior to such sale. The grading procedure described in these test methods is used for checking grades or regrading after the rosin has moved from the primary markets to distributing or consuming points. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Sampling and Grading Rosin

ASTM D3970-05(2011) 氧化滴定法测定涂料干燥剂中铈的标准试验方法

This test method may be used to confirm in the presence of rare earths the stated cerium content of liquid pure cerium or rare earth driers manufactured for use in the coatings industry.1.1 This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate. 1.2 This test method is not applicable to dryer blends. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see Section 7.

Standard Test Method for Cerium in Paint Driers by Oxidimetric Determination

ASTM D2375-05(2011) EDTA 法测定涂料干燥剂中锰含量的标准试验方法

The amount of manganese drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated manganese content of pure liquid manganese drier soluble in toluene-alcohol and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of manganese in liquid paint driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA). 1.2 This test method is not applicable to drier blends. 1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Manganese in Paint Driers by EDTA Method

ASTM D2373-05 用EDTA法测定涂料干燥剂中钴的标准试验方法

The amount of cobalt drier used in oxidizing-type coatings significantly affects their drying properties. This test method may be used to confirm the stated cobalt content of a pure liquid cobalt drier soluble in glacial acetic acid and manufactured for use by the coatings industry.1.1 This test method covers a titrimetric determination of cobalt in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate (EDTA).1.2 This test method is not applicable to drier blends. If driers other than cobalt are present, they may interfere by reacting with EDTA under the conditions used for analysis.1.3 All cations that can be titrated with EDTA in alkaline media interfere and must not be present in the sample.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Cobalt in Paint Driers by EDTA Method