G52 涂料辅助材料 标准查询与下载

DIN 53246:2009 油漆和清漆用溶剂.乙酸酯.交付规范.进一步要求和试验方法

Solvents for paints and varnishes - Acetic esters - Delivery specification, further requirements and methods of test

DIN 53245:2009 油漆和清漆用溶剂.醇类.供应规范,进一步的性能和试验方法

Solvents for paints and varnishes - Alcohols - Supply specification, further properties and methods of test

ASTM D5062-09 容积/重量测定法测定树脂溶液稀释度的标准试验方法

This test method provides a means for resin producers and users as well as solvent and varnish manufacturers to rate various types of resins for solubility by assigning a numerical dilutability value. This percent dilutability value can be used to differentiate resin types for end users and can be utilized as a quality control tool by resin manufacturers. When running a series of these tests, the same lot or batch of dilution solvent must be used throughout to ensure reproducible results.1.1 This test method covers both volumetric and gravimetric determination of resin solution dilutability which gives a numerical value for the overall solubility of the resin expressed as percent dilutability. 1.2 This test method is applicable only if the test solution is of sufficient clarity to allow accurate visual judgement of the end point and of low enough viscosity for efficient mixing to take place. 1.3 This test method is primarily for, but not limited to, resins used in the printing ink industry. 1.4 The percent solvent tolerance of a resin can be determined using this test method if the solvent in the resin solution and the dilution solvent are the same. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Resin Solution Dilutability by Volumetric/Gravimetric Determination

BS ISO 13885-1:2008 涂料和清漆用粘合剂.凝胶渗透色谱法(GPC).用四氢呋喃(THF)作洗提液

Binders for paints and varnishes. Gel permeation chromatography (GPC). Tetrahydrofuran (THF) as eluent

DIN EN ISO 3681 Berichtigung 1:2008 涂料和清漆用粘合剂.皂化值的测定.滴定法.技术勘误DIN EN ISO 3681-2007-10

Binders for paints and varnishes - Determination of saponification value - Titrimetric method (ISO 3681:1996); German version EN ISO 3681:1998, Corrigendum to DIN EN ISO 3681:2007-10

ISO 13885-1:2008 涂料和清漆用粘合剂.凝胶渗透色谱法(GPC).第1部分:用四氢呋喃(THF)作洗提液

This part of ISO 13885 describes the determination of the molar-mass distribution, number-average molar mass Mn and mass-average molar mass Mw of polymers that are soluble in THF (tetrahydrofuran) by gel permeation chromatography (GPC)I). It is possible that, in spite of the good repeatability obtained with this method, it cannot be used with certain polymer types because of specific interactions, such as adsorption within the sample/eluentJcolumn system. The method is not an absolute one and requires calibration with commercially available unbranched- polystyrene standards that have been characterized by absolute methods. The results for samples of polymers other than polystyrene are therefore only comparable within groups of samples of the same type. The conditions specified in this part of ISO 13885 are not suitable for the GPC analysis of polymer samples with .~/w values greater than 106 (see Annex C). No correction methods, e.g. for the elimination of peak broadening, are included in this part of ISO 13885. If absolute molar-mass values are required, an absolute method, e.g. membrane osmometry for .Un or light scattering for Mw, must be used.

Binders for paints and varnishes - Gel permeation chromatography (GPC) - Part 1: Tetrahydrofuran (THF) as eluent

SANS 5126:2008 涂料粘合剂的粘度

Specifies a method for the determination of the viscosity of binders for paints.

Viscosity of binders for paints

ASTM C647-08 胶合辅料和涂覆品的性能及试验的标准指南

Each of the properties listed should be considered in selecting materials for specific projects. A list of the selected properties with limiting values assigned will form a part of the product specification. All of the properties may not be pertinent in any specific situation, and all of the tests outlined may not be required. A condition to any specification must be an evaluation of the proposed use to determine which properties may be required. Membrane reinforcements are frequently specified and used with mastics and coatings. Service properties of such systems of finishes may be different from the unreinforced finishes; therefore, it is essential to test specimens of the reinforced system.1.1 This guide identifies properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation. 1.2 These properties relate to application and service. Each property is defined, and its significance and suggested test methods are described. 1.3 The properties appear in the following order in this guide. Paragraph Application Properties6 Consistency6.1 Coverage6.2 Build6.3 Wet Flammability6.4 Toxicity6.5 Temperature and Humidity Range6.6 Surface Wetting and Adhesion6.7 Gap Filling and Bridging6.8 Sizing and Sealing6.9 Corrosion or Solvent Attack6.10 Drying Time and Curing Time6.11 Shrinkage6.12 Storage Stability6.13 Freeze-Thaw Stability6.14 Service Properties7 Specimen Preparation7.1 Outdoor Durability7.2 Environmental Resistance7.3 Temperature Limits7.3.1 Chemicals and Water Resistance7.3.2 Mold and Mildew Resistance7.3.3 Surface Flammability7.4 Water-Vapor Transmission Rate7.5 Adhesion7.6 Damage Resistance7.7

Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation

ASTM D2627-08(2012) 二丙酮醇的标准规格

1.1 This specification covers diacetone alcohol.2 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Diacetone Alcohol

ASTM D233-08 松脂的抽样和测试的标准试验方法

The test procedures described in this standard were developed when the chief use for turpentine was as a solvent. Currently however, the chief use for turpentine (and pinenes) is as raw materials for the production of resins and synthetic organic chemicals. Thus the chemical composition of turpentines and pinenes is extremely important and tests, in addition to the ones described in these test methods, are required in order to fully characterize turpentines and pinenes. The most widely used technique for determining the chemical composition of turpentines (and pinenes) is gas chromatography (see Test Methods D 6387).1.1 These test methods cover procedures for sampling and testing turpentine, as defined by the Code of Federal Regulations and Terminology D 804. These test methods are also used for the sampling and testing of pinenes, the major components of most turpentines. 1.2 These test methods primarily measure the physical rather than the chemical properties of turpentines and pinenes. As turpentines and pinenes are currently used chiefly as chemical raw materials for the production of resins and synthetic organic chemicals, chemical composition is also very important. Consequently, testing the chemical composition of turpentines and pinenes by gas chromatography has displaced these test methods to a large extent. (See for example Test Methods D 6387.) 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods of Sampling and Testing Turpentine

NF T30-406*NF EN ISO 11909:2007 色漆和清漆用粘合剂.聚亚安酯树脂.试验的通用方法

Binders for paints and varnishes - Polyisocyanate resins - General methods of test.

DIN EN ISO 10283:2007 涂料和清漆用粘合剂.异氰酸酯树脂中二异氰酸酯单体的测定

This international Standard specifies a gas-chromatographic method for determining monomeric diisocyanates such as toluene diisocyanate,hexamethylene diisocyanate,isophorone diisocyanate,diphenylmethane diisocyanate and other diisocyanates in isocyanate resins as defined in Clause 3 and in solutions prepared from such resins,insofar as these are used in the formulation of paints and similar coating materials.

Binders for paints and varnishes - Determination of monomeric diisocyanates in isocyanate resins (ISO 10283:2007); English version of DIN EN ISO 10283:2007-11

NF T30-096*NF EN ISO 7143:2007 涂料和清漆用粘合剂.表征水基粘合剂的试验方法

Binders for paints and varnishes - Methods of test for characterizing water-based binders.

DIN EN ISO 3681:2007 涂料和清漆的粘合剂.皂化值的测定.滴定法

This international Standard specifies a titrimetric metohd for determining the esterified-acid content in binders for paints and varnishes,free acids and acid anhydrides being necessarily included in the result obtained. Because different binders vary in their resistance to saponification,this international Standard is of limited applicability.If necessary,completeness of saponification may be checked by repeating the test under more severe conditions achieved by the use of longer saponification time,more concentrated potassium hydroxide solution,or a higher-boiling alcohol as solvent. Annex A specifies a procedure suitable for binders that saponify with difficulty. Themethod is not applicable to those materials that show further reaction with alkalis beyond normal saponification.

Binders for paints and varnishes - Determination of saponification value - Titrimetric method (ISO 3681:1996); English version of DIN EN ISO 3681:2007-10

KS M ISO 3262-19:2007 涂料用填充剂.规范和试验方法.第19部分:沉淀石英

이 규격은 침강 실리카의 품질규격과 그에 따른 시험방법에 대하여 규정한다.

Extenders for paints-Specifications and methods of test-Part 19:Precipitated silica

KS M ISO 3262-2:2007 涂料用填充剂.规范和试验方法.第2部分:重晶石(天然硫酸钡)

KS M ISO 3262 규격의 일부로 도료용 바라이트(천연 황산바륨) 체질 안료의 규정된

Extenders for paints－Specfications and methods of test－Part 2：Barytes(natural barium sulfate)

KS M ISO 3262-17:2007 涂料用填充剂.规范和试验方法.第17部分:沉淀硅酸钙

이 규격은 침강 규산칼슘의 품질 규격과 그에 따른 시험방법에 대하여 규정한다.

Extenders for paints－Specifications and methods of test－Part 17：Precipitated calcium silicate

KS M ISO 3262-6:2007 涂料用填充剂.规范和试验方法.第6部分:沉淀碳酸钙

KS M ISO 3262의 부속 규격으로서, 도료용 침강 탄산칼슘 체질 안료의 품질과 그의

Extenders for paints－Specification and methods of test－Part 6：Precipitated calcium carbonate

KS M ISO 3262-20:2007 涂料用填充剂.规范和试验方法.第20部分:烟化石英

이 규격은 발연 실리카의 품질규격과 그에 따른 시험방법에 대하여 규정한다.

Extenders for paints－Specifications and methods of test－Part 20：Fumed silica

KS M ISO 3262-22:2007 涂料用填充剂.规范和试验方法.第22部分:热碱处理的硅藻土

이 규격은 용융 하소 규조토에 대한 품질과 시험방법에 대하여 규정한다.

Extenders for paints-Specifications and methods of test-Part 22:Flux-calcined kieselguhr