G54 颜料 标准查询与下载

DIN EN 14469-3:2004 颜料和补充剂.增塑聚氯乙烯(PVC-P)中着色剂的试验.第3部分:白颜料相对染色强度的测定

This Part of EN 14469 specifies a method of determining the relative tinting strength of white pigments in PVC-P.

Pigments and extenders - Testing of colouring materials in plasticized polyvinyl chloride (PVC-P) - Part 3: Determination of the relative tinting strength of white pigments; German version EN 14469-3:2004

ARMY MIL-Z-291 G VALID NOTICE 2-2004 工业氧化锌 [代替:ARMY MIL-Z-00291 D]

MIL-Z-291G remains inactive for new design, however, the document is valid for use.

ZINC OXIDE, TECHNICAL [Use In Lieu Of: ARMY MIL-Z-00291 D]

NF T31-310-4:2004 颜料和稀释剂.扩散方法和在塑料中可扩散性的评定.第4部分:用双滚研磨机测定聚乙烯中白颜料的色度特性和易扩散性

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 4 : determination of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling.

NF T31-311-3*NF EN 14469-3:2004 颜料和稀释剂.增塑聚氯乙烯(PVC-P)中着色剂的检验.第3部分:白颜料相对着色力的测定

Pigments and extenders - Testing of colouring materials in plasticized polyvinyl chloride (PVC-P) - Part 3 : determination of the relative tinting strength of white pigments.

DIN EN 13900-4:2004 颜料和稀释剂.扩散方法和在塑料中可扩散性的评估.第4部分:由双滚研磨机测定聚乙烯中的白颜料的颜色性能和易扩散性

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 4: Determination of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling; German version EN 13900-4:2004

BS EN 13900-4:2004 颜料和填充剂.扩散方法和在塑料中可扩散性的评定.用双辊研磨机测定聚乙烯中白颜料的颜色性能和易扩散性

This Part of EN 13900 specifies a method of determining the colouristic properties of a test pigment in polyethylene (PE) relative to a standard, and the ease of dispersion DHPE of pigments from the differences in tinting strength of dispersing colouring materials under various conditions. The method is appropriate for use with white pigments. The ease of dispersion determined in this way is valid only for the dispersion equipment, dispersion conditions and dispersion medium being used. The use of test conditions differing from those specified can give different results; this applies both to the absolute magnitude and to the relation between values of the ease of dispersion of various pigments. The subscript DHPE is therefore used to designate the value obtained as specified in this Part of EN 13900.

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling

JIS K 5116:2004 二氧化钛(颜料)

この規格は，二酸化チタンからなる顔料の品質及び試験方法について規定する。

Titanium dioxide (pigment)

HG/T 3726-2003 荧光增白剂 CF-351

Fluorescent whitening agent CF-351

HG/T 2549-2003 还原橄榄绿5G细粉

Reduced olive green 5G fine powder

HG/T 3724-2003 媒介黑PV（C I 媒介黑9）

Medium Black PV (CI Medium Black 9)

NF T31-310-3:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.第3部分:用两辊磨测定色彩特点和黑色及彩色颜料在聚乙烯中的易扩散性

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3 : determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling.

NF T31-310-1:2003 颜料和填料.塑料制品的色散方法和色散性的评估.第1部分:一般导言

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1 : general introduction.

NF T31-310-2:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.第2部分:用两辊磨测定色彩特点和在增塑聚氯乙烯中的易扩散性

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 2 : determination of colouristic properties and ease of dispersion in plasticized polyvinyl chloride by two-roll milling.

DIN EN 13900-2:2003 颜料和填料.扩散方法和在塑料中可扩散性的评估.第2部分:用两辊研磨测定色彩特点和在增塑聚氯乙烯中的易扩散性

This part of EN 13900 specifies a method of determining the ease of dispersion DH/PVC-P of pigments from the differences in colour strength on dispersing colouring materials under various conditions in plasticized polyvinyl chloride (PVC-P) compounds. The method is appropriate for use with organic and inorganic colour pigments and for pigment preparations.

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 2: Determination of colouristic properties and ease of dispersion in plasticized polyvinylchloride by two-roll milling; German version EN 13900-2:2003

DIN EN 13900-3:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.第3部分:用两辊研磨测定色彩特点和黑色及彩色颜料在聚乙烯中的易扩散性

This part of EN 13900 specifies a method of determining in polyethylene (PE) the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DH/PE of pigments from the differences in colour strength on dispersing colouring materials under various conditions. The method is appropriate for use with organic and inorganic black and colour pigments.#,,#

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling; German version EN 13900-

DIN EN 13900-1:2003 颜料和填料.扩散方法和在塑料中可扩散性的评估.第1部分:概述

This part of EN 13900 provides an introduction to the various parts of EN 13900 which describe methods for dispersing pigments and extenders in plastics materials in order to determine their dispensibility. Methods of assessing the ease of dispersion are described in the subsequent parts of EN 13900. The various procedures described permit comparisons to be made between similar pigments (for example between a test sample and an agreed reference pigment).

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 1: General introduction; German version EN 13900-1:2003

BS EN 13900-1:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.概述

This part of this European Standard provides an introduction to the various parts of this European Standard which describe methods for dispersing pigments and extenders in plastics materials in order to determine their dispersion characteristics and colouristic properties. Methods of assessing dispersion characteristics are described in the subsequent parts of this European Standard. The various procedures described permit comparison to be made between similar pigments (for example between a test sample and an agreed reference pigment). The results provide an indication of relative dispersibility under practical conditions of use, provided that the test procedure and plastics material selected are appropriate.

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - General introduction

BS EN 13900-2:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.用两辊磨压测定色彩特点和在增塑聚氯乙烯中的易扩散性

This part of this European Standard specifies a method of determining the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DHPVC-P of pigments from the differences in colour strength on dispersing colouring materials under various conditions in plasticized polyvinyl chloride (PVC-P) compounds. The method is appropriate for use with organic and inorganic black and colour pigments and for pigment preparations. The ease of dispersion determined in this way is valid only for the dispersion equipment, dispersion conditions and dispersion medium being used. The use of test conditions differing from those specified may give different results; this applies both to the absolute magnitude and to the relation between values of the ease of dispersion of various pigments. The subscript DHPVC-P is therefore used to designate the value obtained as specified in this part of this European Standard. The principle of this standard may also be used for routine quality control purposes by reference to the photometric data generated from the sheets milled at 130 ℃. For quality control purposes, the ratio of pigment to TiO2 may be agreed between the interested parties. Ratios of 1:10 for organic pigments and 0,2 to 0,5:1 for inorganic pigments are suggested as convenient and widely used standard ratios. Annex A is informative and gives a description of a suitable basic compound.

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion in plasticized polyvinyl chloride by two-roll milling

BS EN 13900-3:2003 颜料和填充剂.扩散方法和在塑料中可扩散性的评估.用两辊磨压法测定色彩特点和炭黑及彩色颜料在聚乙烯中的易扩散性

This part of this European Standard specifies a method of determining in polyethylene (PE) the colouristic properties of a test pigment relative to a standard, and the ease of dispersion DHPE of pigments from the differences in colour strength on dispersing colouring materials under various conditions. Method A is appropriate for use with organic powder pigments and carbon black pigments in powder form, many of which are subject to compaction (reagglomeration under pressure), for inorganic pigments in powder form and for pigment preparations in powder or flake form. Method B is appropriate for testing pigments and pigment preparations in granular form and for inorganic pigments in any form. The ease of dispersion determined in this way is valid only for the dispersion equipment, dispersion conditions and dispersion medium being used. The use of test conditions differing from those specified may give different results; this applies both to the absolute magnitude and to the relation between values of the ease of dispersion of various pigments. The subscript DHPE is therefore used to designate the value obtained as specified in this part of this European Standard.

Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Determination of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling

NF T31-223:2003 颜料和填料的一般试验方法.第17部分:白色颜料调淡力的比较

General methods of test for pigments and extenders - Part 17 : comparison of lightening power of white pigments.