J57 插、拉、刨、锯床 标准查询与下载

JB/T 9931.2-2011 卧式弓锯床.第2部分：精度检验

JB/T 9931的本部分规定了卧式弓锯床的几何精度和工作精度的要求及检验方法。 本部分适用于最大锯削直径160 mm～400 mm的卧式弓锯床。 最大锯削直径小于160 mm或大于400 mm的卧式弓锯床可参照本部分使用。

Horizontal hack sawing machine.Part 2:Testing of the accuracy

JB/T 10226.2-2011 龙门铣刨床.第2部分：技术条件

JB/T 10226的本部分规定了龙门铣刨床制造和验收的技术要求。 本部分适用于最大刨削宽度为800～2000mm的一般用途的普通精度龙门铣刨床。

Double column milling-planning machines.Part 2:Specifications

JB/T 4182.1-2011 立式内拉床.第1部分：型式与参数

JB/T 4182的本部分规定了立式内拉床的系列构成、基本参数。 本部分适用于新设计的一般用途的立式内拉床（以下简称机床）。

Vertical internal broaching machines.Part 1:Types and parameters

JB/T 3362.2-2011 牛头刨床.第2部分： 精度检验

JB/T 3362的本部分规定了牛头刨床的几何精度和工作精度的要求及检验方法。 本部分适用于最大刨削长度200mm～1500mm的牛头刨床。

Shaping machines.Part 2:Testing of the accuracy

JB/T 8770.1-2011 板料边缘刨床.第1部分：精度检验

JB/T 8770的本部分规定了一般用途的板料边缘刨床的预调精度、几何精度和工作精度检验要求及方法。 本部分适用于最大报销长度为6000mm～16000mm的板料边缘刨床。

Plate edge planing machine.Part 1:Testing of the accuracy

JB/T 2825.1-2011 插床.第1部分 参数

JB/T 2825的本部分规定了插床的基本参数。 本部分适用于新设计的最大插削长度200mm～1600mm的插床。

Slotting machines.Part 1:Parameters

JB/T 4182.2-2011 立式内拉床.第2部分：静刚度

JB/T 4182的本部分规定了立式内拉床静刚度检验（以下简称刚度检验）的技术要求和检验方法。 本部分适用于额定拉力为20kN、40kN、50kN、63kN、100kN、200kN、300kN、400kN、600kN、800kN、1000kN、1200kN和1500kN的立式内拉床。

Vertical internal broaching machines.Part 2:Static rigidity

JB/T 2732.1-2011 悬臂刨床龙门刨床.第1部分：型式与参数

JB/T 2732的本部分规定了悬臂刨床和龙门刨床的型式和参数。 本部分适用于新设计的悬臂刨床和龙门刨床。

Cantilever and portal-type planers.Part 1:Types and parameters

JB/T 3364.2-2011 圆锯床.第2部分：精度检验

JB/T 3364的本部分规定了圆锯床的几何精度和工作精度的要求及检验方法。本部分适用于最大圆锯片直径315 mm～2000 mm的卧式圆锯床、摆式圆锯床和立式圆锯床。 最大圆锯片直径小于315 mm或大于2000 mm的圆锯床可参照本部分使用。

Circular sawing machine.Part 2:Testing of the accuracy

JB/T 9931.3-2011 卧式弓锯床.第3部分：技术条件

JB/T 9931的本部分规定了卧式弓锯床的制造与验收的技术条件。 本部分适用于最大锯削直径为160 mm～400 mm的卧式弓锯床。 最大锯削直径小于160 mm或大于400 mm的卧式弓锯床可参照本部分使用。

Horizontal hack sawing machine.Part 3:Specifications

NF E60-460:2010 机床.安全性.冷金属锯床.

Machine tools - Safety - Sawing machines for cold metal.

NF E60-460/IN1:2010 机床.安全性.冷金属锯床.

Machine tools - Safety - Sawing machines for cold metal.

DIN EN 61029-2-1:2010 便携式电动工具的安全性.第2-1部分:圆锯的详细要求(IEC 61029-2-1-1993,修改件+A1-1999+A2-2001).德文版本EN 61029-2-1-2010

Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saw benches (IEC 61029-2-1:1993, modified + A1:1999 + A2:2001); German version EN 61029-2-1:2010

KS B ISO 6481:2010 立式平面拉床的验收条件.精度试验

이 표준은 일반적인 정확정밀도를 갖는 수직 외면 브로칭 머신의 예비 수평도 시험, 기하학적

Acceptance conditions for vertical surface type broaching machines-Testing of accuracy

KS B ISO 6480:2010 卧式内孔拉床的验收条件.精度试验

이 표준은 일반적인 정확정밀도를 가진 수평 내면 브로칭 머신의 예비 수평도 시험, 정확정밀

Conditions of acceptance for horizontal internal broaching machines-Testing of the accuracy

DIN EN 61029-2-9:2010 移动式电动工具的安全性. 第2-9部分: 斜切锯的详细要求; （IEC 61029-2-9: 1995, 修改件）; 德文版本 EN 61029-2-9: 2009

Safety of transportable motor-operated electric tools - Part 2-9: Particular requirements for mitre saws (IEC 61029-2-9:1995, modified); German version EN 61029-2-9:2009

DIN EN 61029-2-11:2010 便携式马达安全性. 电动工具. 第2-11部分: 组合横切锯和台锯的详细要求（IEC 61029-2-11: 2001, 修改件）; 德文版本EN 61029-2-11: 2009

Safety of transportable motor-operated electric tools - Part 2-11: Particular requirements for combined mitre and bench saws (IEC 61029-2-11:2001, modified); German version EN 61029-2-11:2009

DIN EN 15027:2010 施工现场用便携式平锯和线状锯设备.安全性

This standard specifies the safety requirements for transportable wall saw and wire saw equipment intended for the construction industry, and used to make cuts on walls, ceilings and floors composed of mineral construction materials and/or composite materials. For this purpose the machines are used with diamond tools. Machines covered by this standard may be powered by: electric motor, IC engine, electro-hydraulic drive and IC engine-hydraulic drive.

Transportable wall saw and wire saw equipment for job site - Safety; German version EN 15027:2007+A1:2009

DIN EN 13862:2010 地板切割机.安全性

This standard specifies the safety requirements for self-propelled ride-on and pedestrian controlled floor cutting-off machines having power feed, manual feed or hand feed for sawing, grooving and milling floor surfaces made of concrete, asphalt and similar building materials where the main power is supplied by electric or internal combustion prime engine. This standard does not apply to machines moving along a rail; hand-held portable cutting off machines for construction materials mounted on a mobile support, to be used as floor saws and for remote controlled machines.

Floor cutting-off machines - Safety; German version EN 13862:2001+A1:2009

DIN EN 13985:2009 机械工具安全.剪板机德文版本EN 13985:2003+A1:2009

1.1 This European Standard specifies technical safety requirements and measures to be adopted by persons undertaking the design as defined in 3.11 of EN 292-1:1991, manufacture and supply of guillotine shears which are intended to work cold metal or material partly of cold metal as defined in 3.1.7 and hereafter referred as machines. 1.2 This standard also covers guillotine shears whose primary intended use is to work cold metal, which are to be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather). 1.3 The requirements in this standard take account of intended use as defined in 3.12 of EN 292-1:1991. This standard presumes access to the guillotine shear from all directions, deals with the hazards described in clause 4, and specifies the safety requirements and/or protective measures for both the operator and other exposed persons 1.4 This standard also applies to ancillary devices which are an integral part of the guillotine shear. This standard also applies to machines which are integrated into an automatic production line where the hazards and risk arising are comparable to those of machines working separately. 1,5 This standard includes guillotine shears in which energy is imparted to the blade by a number of means, e.g.: a) mechanically driven from a motor through a friction clutch; b) through a direct drive motor and brake; c) through hydraulic pressure; d) through pneumatic pressure. 1.6 This standard does not cover machines whose principal designed purpose is: a) cutting in other than a straight line (e.g. at nibbling machines); b) cutting by continuous action at crocodile shears (see 3.4). 1.7 This standard does not cover the safety requirements related to the use of PES or PPS. They will be dealt with at its next revision. 1.8 This standard is not applicable to machines which are manufactured before the date of publication of this document by CEN.

Machine tools - Safety - Guillotine shears (includes Amendment A1:2009); English version of DIN EN 13985:2009-11