共找到 244 条与 插、拉、刨、锯床 相关的标准,共 17 页
A-A-59662, dated 05 June 2001, has been reviewed and determined to be valid for use in acquisition.
CHAIN SAW (PORTABLE, PNEUMATIC-MOTOR-DRIVEN)
Acceptance conditions for vertical surface type broaching machines - Testing of accuracy.
Acceptance conditions for broaching machines of vertical internal type - Testing of accuracy.
This International Standard specifies the designation of groups of high-speed steels used for manufacturing cutting tools such as taps, drills, etc. It is not intended to specify the composition of high-speed steels, which is stated in ISO 4957.
Cutting tools - Designation of high-speed steel groups
The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil
SAW, BAND, CUTOFF, HORIZONTAL, AND COMBINATION HORIZONTAL AND VERTICAL [Superseded: DLA MIL-S-45814 D CANC NOTICE 1, DLA MIL-S-45814 D, DLA MIL-S-45814 C, DLA MIL-C-45814 B, DLA MIL-C-45814 A]
The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil.
CUTOFF MACHINE, ABRASIVE DISK, CHOP-STROKE [Superseded: DLA MIL-C-80021 B CANC NOTICE 1, DLA MIL-C-80021 B (1), DLA MIL-C-80021 B, DLA MIL-C-80021 A (1), DLA MIL-C-80021 A, DLA MIL-C-80021, DLA MIL-C-80071 B CANC NOTICE 2, DLA MIL-C-80071 B VALID
This commercial item description (CID) covers the requirements for electric motor driven, two-wheel, utility type, bench and pedestal mounted, grinding machines.
GRINDING MACHINES, UTILITY, BENCH AND PEDESTAL
이 규격은 금속 냉간 절단용 톱의 드라이브의 호환성 치수를 규정한다. 고속도강 일체형 톱과
Solid and segmental circular saws for cold cutting of metals-Interchangeability dimensions of the drive-Saw diameter range 224∼2 240 mm
1.1 This standard specifies the safety requirements and measures to be adopted by persons undertaking the design, construction and supply (including installation, setting–up, maintenance, and repair) of machines whose primary intended use is for sawing cold metal (ferrous and non-ferrous), or material partly of cold metal, by means of a saw blade. 1.2 This standard takes into account the intended use, reasonably foreseeable misuse, machine setting and blade fitting, maintenance and cleaning, and their effects on the safety of operators and other exposed persons. It presumes access to the machine from all directions at floor level and addresses both normal operation and unexpected or unintended starting. 1.3 This standard applies to the ancillary devices which form an integral part of the machine. Where such devices are not an integral part of the machine, the designer, manufacturer or supplier of the installation should take into account their intended use, and should make provision for the safe linking of such devices with the machine. 1.4 This standard applies to (metal) sawing machines which are manufactured after the date of publication by CEN of this standard.
Machine tools.Safety.Sawing machines for cold metal
1 This standard specifies the safety requirements and measures to be adopted by persons undertaking the design, construction and supply (including installation, setting-up, maintenance, and repair) of machines whose primary intended use is for sawing cold metal (ferrous and non-ferrous), or material partly of cold metal, by means of a saw blade. 2 This standard takes into account the intended use, reasonably foreseeable misuse, machine setting and blade fitting, maintenance and cleaning, and their effects on the safety of operators and other exposed persons. It presumes access to the machine from all directions at floor level and addresses both normal operation and unexpected or unintended starting. 3 This standard applies to the ancillary devices which form an integral part of the machine. Where such devices are not an integral part of the machine, the designer, manufacturer or supplier of the installation should take into account their intended use, and should make provision for the safe linking of such devices with the machine. 4 This standard applies to (metal) sawing machines which are manufactured after the date of publication by CEN of this standard.
Machine tools - Safety - Sawing machines for cold metal
Machine-tools - Safety - Guillotine shears.
This clause of part 1 is applicable except as follows: 1 Addition: This European Standard applies to transportable mitre saws with a blade diameter not exceeding 350 mm. intended for cutting wood and analogue materials. 2 Addition: This standard does not apply to transportable mitre saws used to cut steel, brass or food. Mitre saws for cutting wood other than transportable are covered by EN 1870-3. Tools combining the function of a mitre saw with the function of a circular saw bench are covered by EN 61029-2-11.
Safety of transportable motor-operated tools - Particular requirements for mitre saws
이 규격은 그라인딩 휠, 소(saw) 등과 같은 공산품 제조에 사용되는 다이아몬드 및 입방
Abrasive products-Grain sizes of diamond or cubic boron nitride
Covers the safety requirements as they relate to the design, installation, operation and maintenance of powered shears.
Machine Tools – Safety Requirements for Shears
Covers the safety requirements as they relate to the design, installation, safeguarding, operation and maintenance of powered machines used to saw metals.
Safety Requirements for Metal Sawing Machines
A-A-59200, dated 17 June 1998, has been reviewed and determined to be valid for use in acquisition
GRINDING MACHINES, SURFACE, ROTARY TABLE, VERTICAL SPINDLE
To be read in conjunction with BS EN 61029-1:2000
Safety of transportable motor-operated tools - Particular requirements for circular saw benches
This British Standard specifies design, dimensions and tolerances for hole-saws up to 152 mm diameter. The following types of hole-saws are specified: a) toothed hole-saws; b) tipped-toothed hole-saws; c) abrasive grit-edged hole-saws. This British Standard also includes dimensions of hole-saw driving arbors and other accessories.
Specification for hole-saws
To be read in conjunction with BS EN 61029-1:2000
Safety of transportable motor-operated tools - Particular requirements for band saws
本标准规定了立式带锯床的制造与验收的技术条件。 本标准适用于最大锯削厚度125mm~1600mm的立式带锯床。 最大锯削厚度大于1600mm的立式带锯床可参照本部分。
Vertical band sawing machine Part 4:Specifications
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号