J90 活塞式内燃机与其它动力设备综合 标准查询与下载
共找到 478 条与 活塞式内燃机与其它动力设备综合 相关的标准，共 32 页
本标准规定了采用批次热重力分析(TGA)法的多通道碳黑过滤试验方法，在线连续傅立叶转换红外线(FTIR)，或其他已被认可的碳黑测量技术，以评估内燃机用单级或多级离心式或其他型式碳黑去除装置(SRD)的初始滤清效率，试验时流体流量保持恒定。本试验程序确定碳黑去除装置以时间加权的平均初始碳黑去除效率。 本试验方法适用于额定流量为0.5 L/min~75 L/min的碳黑去除装置(SRD)。
Performance test method for diesel engine soot-removal devices in lubricating oils.Initial filtration efficiency
- ICS
- 27.020
- CCS
- J90
- 发布
- 2014-05-06
- 实施
- 2014-10-01
The objective of this glossary is to establish uniform definitions of parts and terminology for engine cooling systems. Components included are all those through which engine coolant is circulated: water pump, engine oil cooler, transmission and other coolant-oil coolers, charge air coolers, core engine, thermostat, radiator, external coolant tanks, and lines connecting them.
Glossary of Engine Cooling System Terms
- ICS
- 01.040.43;43.060.30
- CCS
- J90
- 发布
- 2014-02-07
- 实施
이 표준은 출력, 연료 소비량, 윤활유 소비량의 표기 및 시험방법의 요건에 대하여 규정한다.이 표준은 출력의 표기(statement of power)를 단순화하고 의사 소통을 원활하게 할 수 있도록 엔진의제동 출력 시험방법을 규정한다. 이것은 엔진의 명판에 기재하는 출력의 표기 등에 적용한다.이것은 육상, 철도 및 해상 용도의 왕복 내연 기관에 적용한다.도로 건설 및 토공 기계, 산업 트럭 및 그 밖의 용도로 사용하는 엔진에 적절한 표준이 없을 때는이 표준을 적용할 수 있다.이 표준은 “주변” 표준으로서 “중심” 표준 KS R ISO 15550과 연계하여 적용하는 경우에 한하여 특정엔진의 요건을 완전히 규정할 수 있다.
Reciprocating internal combustion engines — Performance — Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods — Additional requirements for engines for general use
- ICS
- 27.020
- CCS
- J90
- 发布
- 2013-12-05
- 实施
- 2013-12-05
1.1 이 표준은 상거래를 목적으로 생산되는 액체 또는 기체 연료를 사용하는 내연 기관의 표준 기준 조건 그리고 출력, 연료 소비량 및 윤활유 소비량의 공표 및 시험방법에 대하여 규정한다. 이 표준은 다음과 같은 엔진에 적용한다.a) 자유 피스톤 엔진을 제외한, 왕복 내연 기관(RIC: Reciprocating Internal Combustion engine)(스파크 점화 엔진 또는 압축 착화 엔진)b) 로터리 피스톤 엔진이들 엔진은 자연 흡기 방식 또는 기계식 과급기 또는 터보차저를 사용하는 과급 방식의 엔진으로 한다.1.2 이 표준에는 다음 용도로 사용하는 엔진에 적용한다.a) KS R ISO 3046-1에 지정하는 육상, 철도 및 해상b) KS R ISO 1585 및 KS R ISO 2534에 지정하는 자동차의 추진c) KS R ISO 4106에 지정하는 이륜 자동차d) KS B ISO 9249에 지정하는 토공 장비의 추진e) KS V ISO 8665에 지정하는 선체 길이 24 m 이내의 레저용 선박 및 그 밖의 다른 소형 선박의 추진이 표준에는 적합한 표준이 존재하지 않는 도로 건설 장비, 산업 트럭 및 그 밖의 다른 용도에 동력을 제공하는 엔진에도 적용할 수 있다.이 표준에는 제조자 장소의 시험대 및 현장에서 실시하는 시험에도 적용할 수 있다.1.3 특정 엔진 용
Internal combustion engines — Determination and method for the measurement of engine power — General requirements
- ICS
- 27.020
- CCS
- J90
- 发布
- 2013-12-05
- 实施
- 2013-12-05
Diesel engines.NOx reduction agent AUS 32. Part 4: Refilling interface
- ICS
- 13.040.50;43.060.40
- CCS
- J90
- 发布
- 2013-02-20
- 实施
1.1 This document covers terminology relating to engine coolants. It is intended to provide a reference for anyone seeking information on engine coolants, and also to provide a uniform set of definitions for use in preparing ASTM specifications, test methods and other standard documents. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Terminology for Engine Coolants and Related Fluids
- ICS
- 01.040.71 (Chemical technology (Vocabularies)); 71
- CCS
- J90
- 发布
- 2013
- 实施
5.1 Density is a fundamental physical property that can be used in conjunction with other properties to characterize engine coolant concentrates and aqueous engine coolants. 5.2 Determination of the density or relative density of these products is necessary for the conversion of measured volumes to volumes at the standard temperature of 208201;°C (688201;°F). 1.1 This test method covers the determination of the density or relative density of engine coolant concentrates and aqueous engine coolants. 1.2 This test method should not be applied to samples so dark in color that the absence of air bubbles in the sample cell cannot be established with certainty. 1.3 The accepted units of measure for density are grams per milliliter or kilograms per cubic meter. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Note 1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter
- ICS
- 17.060 ; 47.020.20 ; 71.100.45
- CCS
- J90
- 发布
- 2013
- 实施
Reciprocating internal combustion engines - Exhaust emission measurement - Part 9: Test cycles and test procedures for test bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
- ICS
- 13.040.50;27.020
- CCS
- J90
- 发布
- 2012-08
- 实施
Reciprocating internal combustion engines - Safety - Part 1: Compression ignition engines; German version EN 1679-1:1998+A1:2011
- ICS
- 27.020
- CCS
- J90
- 发布
- 2011-09
- 实施
本标准规定了内燃机用光整机产品系列型式、型号、参数、构成、技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于内燃机用自由磨具滚膜表面光整加工设备。其他行业用表面光整加工设备亦可参照使用。
Finishing machines for internal combustion engines
- ICS
- 27.020
- CCS
- J90
- 发布
- 2011-05-18
- 实施
- 2011-08-01
本标准规定了内燃机零部件表面光整加工的术语和定义、光整设备、光整介质、光整加工前对零部件表面的要求、光整加工技术要求、检验方法、光整加工后处理、检验规则、标志、包装、运输及贮存等。 本标准适用于内燃机金属零部件精加工表面。其他行业金属零部件精加工表面亦可参照使用。
Internal combustion engines.Surface finishing for parts.Specifications
- ICS
- 27.020
- CCS
- J90
- 发布
- 2011-05-18
- 实施
- 2011-08-01
Reciprocating internal combustion engines. Vocabulary of components and systems. Main running gear
- ICS
- 01.040.27;27.020
- CCS
- J90
- 发布
- 2011-02-28
- 实施
- 2011-02-28
Diesel engines -- NOx reduction agent AUS 32 -- Part 3: Handling, transportation and storage
- ICS
- 13.040.50;43.060.40
- CCS
- J90
- 发布
- 2011-01-20
- 实施
This part of ISO 7967 defines terms relating to the main running gear of reciprocating internal combustion engines. ISO 2710-1 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.
Reciprocating internal combustion engines - Vocabulary of components and systems - Part 2: Main running gear
- ICS
- 01.040.27;27.020
- CCS
- J90
- 发布
- 2010-12-15
- 实施
- 2010-12-15
Reciprocating internal combustion engines. Vocabulary of components and systems. Valves, camshaft drives and actuating mechanisms
- ICS
- 01.040.27;27.020
- CCS
- J90
- 发布
- 2010-11-30
- 实施
- 2010-11-30
Reciprocating internal combustion engines - Vocabulary of components and systems - Part 3: Valves, camshaft drives and actuating mechanisms
- ICS
- 01.040.27;27.020
- CCS
- J90
- 发布
- 2010-08
- 实施
Reciprocating internal combustion engines - Vocabulary of components and systems - Control and monitoring systems
- ICS
- 01.040.27;27.020
- CCS
- J90
- 发布
- 2010-06-30
- 实施
- 2010-06-30
1.1 Scope. This standard establishes criteria for minimizing the hazards of fire during the installation and operation of stationary combustion engines and gas turbines.
Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines
- ICS
- 27.020;27.040
- CCS
- J90
- 发布
- 2010
- 实施
Reciprocating internal combustion engines -- Exhaust emission measurement -- Part 5: Test fuels
- ICS
- 13.040.50;27.020
- CCS
- J90
- 发布
- 2009-12-21
- 实施
Diesel engines -- NOx reduction agent AUS 32 -- Part 1: Quality requirements
- ICS
- 13.040.50
- CCS
- J90
- 发布
- 2009-12-21
- 实施
