J90 活塞式内燃机与其它动力设备综合 标准查询与下载

KS R ISO 8178-9:2007 往复式内燃机.气体排放测量.第9部分:压燃式发动机瞬态工况排气烟度试验台测量用试验方法和试验周期

이 규격은 시험대 위에서 압축 점화 기관으로부터 스모크 배출물의 평가를 위한 측정 절차와

Reciprocating internal combustion engines－Exhaust emission measurement－Part 9：Test cycles and test procedures for test-bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions

KS R ISO 8178-5:2007 往复式内燃机.气体排放测量.第5部分:试验燃料

이 규격은 KS R ISO 8178-4에서 주어진 배출 가스 배출물 시험 사이클을 수행하기

Reciprocating internal combustion engines－Exhaust emission measurement－Part 5：Test fuels

ARMY MIL-PRF-49080 C-2007 PP-2953D/U和PP-6224C/U型动力物资

This specification establishes the performance and verification requirements for each of the following Power Supplies: the PP-2953D/U and the PP-6224C/U . The power supply furnishes 0-25 amperes over a voltage range of 24 to 32Vdc from nominal 115/230 Vac at 50, 60 or 400 Hz single phase. The power supply can also operate from a 24 Vdc storage battery in the battery standby mode.

POWER SUPPLIES, PP-2953D/U AND PP-6224C/U

KS B ISO 15916:2006 氢系统安全性的基础问题

이 규격은 가스와 액체 형태의 수소를 사용하는데 있어서의 지침을 제공한다. 이것은 기본적인

Basic considerations for the safety of hydrogen systems

KS R ISO 13332:2006 往复式内燃机.发动机底座处测量由高速和中速往复式内燃机产生结构噪声的试验规程

이 규격은 고속 또는 중속 기관의 진동 발생 수준을 측정하고, 획득한 정보의 타당성을 위한

Reciprocating internal combustion engines－Test code for the measurement of structure－borne noise emitted fromhigh－speed and medium－speed reciprocating internal combustion engines measured at the engine feet

KS R ISO 14396:2006 往复式内燃机.发动机功率的测量和检测方法.依据ISO 8178的废气排放试验的补充要求

규격은 ISO 8178에 따라 배출가스 시험에 제출되는 왕복 내연 기관의 동력을 결정하기

Reciprocating internal combustion engines-Determination and method for the measurement of engine power-Additional requirements for exhaust emission tests in accordance with ISO 8178

KS R ISO 6798:2006 往复式内燃机.辐射的空气噪声测量.工程法和简易法

1.1 이 규격은 소음원을 둘러싸는 측정 표면에서의 음압 레벨을 측정하는 방법, 그리고 그

Reciprocating internal combustion engines－Measurement of emitted airborne noise－Engineering method and survey method

KS R ISO 3046-3:2006 往复式内燃机.性能.第3部分:试验测量

이 규격은 ISO 15550에 지정하는 기본 요구 사항에 추가하여, 왕복 내연 기관의 주요

Reciprocating internal combustion engines－Performance－Part 3：Test measurements

KS R ISO 3046-6:2006 往复式内燃机.性能.第6部分:超速保护

이 규격은 왕복동 내연 기관 및 그 피구동 기기를 보호하기 위해 사용되는 과속 제한 장치에

Reciprocating internal combustion engines－Performance－Part 6：Overspeed protection

NF E37-211-1:2006 往复式内燃机.废气排放测量.第1部分:气体和颗粒废物排放的试验床测量

Reciprocating internal combustion engines - Exhaust emission measurement - Part 1 : test-bed measurement of gaseous and particulate exhaust emissions.

JIS B 8008-10:2006 往复式内燃机.排放测量.第10部分:压燃式发动机瞬态工况时排气烟度现场测量用试验周期和试验方法

この現格は，圧縮点火機関からの排気煙排出の評価を現地で行うめの，試験サイクル及び測定方法について規定する。この規格は，主にJIS B 8009-9に従って認証又は型式認定される機関の排気煙濃度測定要領として使用する。JIS B 8009-9は，台上で運転される各種用途の機関における排気煙濃度測定の試験サイクル及び試験方法について規定している。

Reciprocating internal combustion engines -- Exhaust emission measurement -- Part 10: Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions

BS ISO 3046-3:2006 往复式内燃机.性能.试验测量

This part of ISO 3046 specifies the common measurement techniques of the main performance parameters of reciprocating internal combustion engines, in addition to the basic requirements defined in ISO 15550. This is to ensure that the required accuracy of measurement is achieved for comparison of the measured values with those values specified by the engine manufacturer. Where necessary, individual requirements may be given for particular engine applications. This part of ISO 3046 applies to reciprocating internal combustion engines for land, rail-traction and marine use. It may be applied to engines used to propel road construction machines, industrial trucks, and for other applications where no suitable International Standards for these engines exist.

Reciprocating internal combustion engines - Performance - Test measurements

BS ISO 21006:2006 内燃机.发动机重量(质量)说明

ISO 21006:2006 specifies how to make a declaration of the engine weight (mass) for internal combustion engines. For the purposes of this standard, the word weight is used as the direct equivalent of the word mass. ISO 21006:2006 concerns reciprocating internal combustion engines (spark-ignition or compression ignition engines) but excluding free piston engines, and rotary piston engines. NOTE These engines may be naturally aspirated or pressure-charged, either by a mechanical pressure-charger or a turbocharger. ISO 21006:2006 applies to engines for land, rail-traction and marine use, the propulsion of automotive vehicles, propelling (or powering) non-road mobile machinery, motorcycles, the propulsion of agricultural tractors and machines, the propulsion of earth-moving machinery as defined in ISO 6165, and the propulsion of recreational or other small marine craft of full length up to 24 m . In addition, ISO 21006:2006 may be applied to engines used to propel road-construction machines, industrial trucks and for other applications where no suitable International Standard for these engines exists.

Internal combustion engines - Engine weight (mass) declaration

ISO 3046-3:2006 往复式内燃机.性能.第3部分:试验测量

This part of ISO 3046 specifies the common measurement techniques of the main performance parameters of reciprocating internal combustion engines, in addition to the basic requirements defined in ISO 15550. This is to ensure that the required accuracy of measurement is achieved for comparison of the measured values with those values specified by the engine manufacturer. Where necessary, individual requirements may be given for particular engine applications. This part of ISO 3046 applies to reciprocating internal combustion engines for land, rail-traction and marine use. It may be applied to engines used to propel road construction machines, industrial trucks, and for other applications where no suitable International Standards for these engines exist.

Reciprocating internal combustion engines - Performance - Part 3: Test measurements

ISO 21006:2006 内燃机.发动机重量（质量）说明

本标准规定了内燃机的重量(质量)标定方法。 本标准中所用名词重量直接等效于名词质量。 本标准适用于： a） 往复内燃式(RIC)发动机（火花点燃式或压燃式发动机）但不包括自由活塞式发动机； b） 旋转活塞式发动机； 这些发动机可以是自燃吸气式发动机或采用机械增压器或涡轮增压器的增压发动机。 本标准适用于下列用途的发动机： c) 陆用、轨道牵引和船用； d) 车用 c) 驱动(或作为动力）的肺道路移动机械用； f) 摩托车用； g) 农用拖拉机和溶液机械驱动用； h) ISO 6165 标准中定义的土方机械用。 i） 总长不超过24m的游艇等小型船舶用。 本标准也适用于筑路机械、工业卡车以及目前尚无合适标准使用的其他用途的发动机。

Internal combustion engines - Engine weight (mass) declaration

BS ISO 8178-11:2006 往复式内燃机.废气排放测量.瞬态试验条件下非道路车辆排气和颗粒排放量现场测量

This part of ISO 8178 specifies the measurement and evaluation methods for gaseous and particulate exhaust emission from reciprocating internal combustion (RIC) engines under transient conditions on a test bed, necessary for determining one value for each exhaust gas pollutant. The specific transient test cycle covered by this part of ISO 8178 is applicable to compression-ignition engines for mobile use with a power output between 37 kW and 560 kW, excluding engines for motor vehicles primarily designed for road use. This part of ISO 8178 may be applied to engines used in off-road vehicles and diesel powered off-road industrial equipment as described in 8.3.1.3 of ISO 8178-4. This includes e.g. engines for construction equipment including wheel loaders, bulldozers, crawler tractors, crawler loaders, truck-type loaders, off-highway trucks, hydraulic excavators, agricultural equipment, self propelled agricultural vehicles (including tractors), forestry equipment, fork lift trucks, road maintenance equipment and mobile cranes. Many of the procedures described below are detailed accounts of laboratory methods, since determining an emissions value requires performing a complex set of individual measurements, rather than obtaining a single measured value. Thus, the results obtained depend as much on the process of performing the measurements as they depend on the engine and test method.

Reciprocating internal combustion engines - Exhaust emission measurement - Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions

ISO 8178-11:2006 往复式内燃机.废气排放测量.第11部分:瞬态试验条件下非道路车辆发动机排气和颗粒废物排放量现场测量

This part of ISO 8178 specifies the measurement and evaluation methods for gaseous and particulate exhaust emission from reciprocating internal combustion (RIC) engines under transient conditions on a test bed, necessary for determining one value for each exhaust gas pollutant. The specific transient test cycle covered by this part of ISO 8178 is applicable to compression-ignition engines for mobile use with a power output between 37 kW and 560 kW, excluding engines for motor vehicles primarily designed for road use. This part of ISO 8178 may be applied to engines used in off-road vehicles and diesel powered off-road industrial equipment as described in 8.3.1.3 of ISO 8178-4. This includes e.g. engines for construction equipment including wheel loaders, bulldozers, crawler tractors, crawler loaders, truck-type loaders, off-highway trucks, hydraulic excavators, agricultural equipment, self propelled agricultural vehicles (including tractors), forestry equipment, fork lift trucks, road maintenance equipment and mobile cranes. Many of the procedures described below are detailed accounts of laboratory methods, since determining an emissions value requires performing a complex set of individual measurements, rather than obtaining a single measured value. Thus, the results obtained depend as much on the process of performing the measurements as they depend on the engine and test method.

Reciprocating internal combustion engines - Exhaust emission measurement - Part 11: Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions

NFPA 37-2006 固定式内燃机和燃气涡轮的安装和使用标准

This standard establishes criteria for minimizing the hazards of fire during the installation and operation of stationary combustion engines and gas turbines.

Standard for the Installation and Use of Stationary Combustion Engines and Gas Turbines Effective Date: 2/16/2006

ASTM D3147-06(2013) 发动机冷却剂用止漏添加剂的标准试验方法

5.1 The screening procedures simulate the conditions of temperature, pressure, and circulation encountered in service. This test method will indicate whether a product is suitable for further evaluation in vehicles. 1.1 This test method covers screening procedures for the preliminary evaluation of leak-stopping materials intended for use in engine cooling systems. (Heavy-duty users are referred to X1.2.21 in Specification D4485 for additional information.) 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 10.1.

Standard Test Method for Testing Stop-Leak Additives for Engine Coolants

KS R ISO 12345:2005 柴油机.燃料喷射设备的清洁度评定

이 규격은 디젤 기관에 대한 연료 분사 장치를 구성하는 부품 내에서 발견되는 불순물의 양을

Diesel engines-Cleanliness assessment of fuel injection equipment