K48 绝缘子 标准查询与下载

NF C66-550*NF EN 60137:2017 交流电压大于1000V的绝热轴衬

La présente Norme internationale spécifie les caractéristiques et les essais applicables aux traversées isolées.

Insulated bushings for alternating voltages above 1 000 V

DL/T 1726-2017 特高压直流穿墙套管技术规范

Technical specification for UHV DC wall bushing

IEC 60137:2017 交流电压1000V以上的绝缘套管

This International Standard specifies the characteristics and tests for insulated bushings. This standard is applicable to bushings, as defined in Clause 3, intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1000 V and power frequencies of 15 Hz up to and including 60 Hz. Subject to special agreement between purchaser and supplier, this standard may be applied, in part or as a whole, to the following: bushings used in other than three-phase systems; bushings for high-voltage direct current systems; bushings for testing transformers; bushings for capacitors. Special requirements and tests for transformer bushings in this standard apply also to reactor bushings. This standard is applicable to bushings made and sold separately. Bushings which are a part of an apparatus and which cannot be tested according to this standard should be tested with the apparatus of which they form part.

Insulated bushings for alternating voltages above 1000 V

DIN EN 61466-1:2017 额定电压超过1000V的架空线用复合绝缘子串组合件.第1部分:标准强度等级和端接头(IEC 61466-1-2016);德文版本EN 61466-1-2016

Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V - Part 1: Standard strength classes and end fittings (IEC 61466-1:2016); German version EN 61466-1:2016

ASTM C1773-17 在环境温度下连续纤维增强先进陶瓷管试样单调轴向拉伸性能的标准试验方法

5.1 This test method provides information on the uniaxial tensile properties and tensile stress-strain response of a ceramic composite tube—tensile strength and strain, fracture strength and strain, proportional limit stress and strain, tensile elastic modulus, etc. The information may be used for material development, material comparison, quality assurance, characterization, and design data generation. 5.2 Continuous fiber-reinforced ceramic composites (CFCCs) are composed of continuous ceramic-fiber directional (1-D, 2-D, and 3-D) reinforcements in a fine grain-sized (<508201;µm) ceramic matrix with controlled porosity. Often these composites have an engineered thin (0.1 to 108201;µm) interface coating on the fibers to produce crack deflection and fiber pull-out. These ceramic composites offer high temperature stability, inherent damage tolerance, and high degrees of wear and corrosion resistance. As such, these ceramic composites are particularly suited for aerospace and high temperature structural applications (1, 2).3 5.3 CFCC components have a distinctive and synergistic combination of material properties, interface coatings, porosity control, composite architecture (1-D, 2-D, and 3-D), and geometric shape that are generally inseparable. Prediction of the mechanical performance of CFCC tubes (particularly with braid and 3-D weave architectures) cannot be made by applying measured properties from flat CFCC plates to the design of tubes. Direct uniaxial tensile strength tests of CFCC tubes are needed to provide reliable information on the mechanical behavior and strength of tube geometries. 5.4 CFCCs generally experience “graceful” fracture from a cumulative damage process, unlike monolithic advanced ceramics which fracture catastrophically from a single dominant flaw. The tensile behavior and strength of a CFCC are dependent on its inherent resistance to fracture, the presence of flaws, and any damage accumulation processes. These factors are affected by the composite material composition and variability in material and testing—components, reinforcement architecture and volume fraction, porosity content, matrix morphology, interface morphology, methods of material fabrication, test specimen preparation and conditioning, and surface condition. 5.5 The results of tensile tests of test specimens fabricated to standardized dimensions from a particular material or selected portions of a part, or both, may not totally represent the strength and deformation properties of the entire, full-size end product or its in-service behavior in different environments. 5.6 For quality control purposes, results derived from standardized tubular tensile test specimens may be considered indicative of the response of the material from which they were taken, given primary processing conditions and post-processing heat treatments. 1.1 This test method determines the axial tensile strength and stress-strain response of continuous fiber-reinforced advanced ceramic composite tubes at ambient temperature und......

Standard Test Method for Monotonic Axial Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramic Tubular Test Specimens at Ambient Temperature

DL/T 1673-2016 换流变压器阀侧套管技术规范

Technical specifications for valve side bushings of converter transformers

BS EN 62772:2016 交流电压高于1000 V, 直流电压高于1500 V变电站用电站支柱复合空心绝缘子. 定义, 试验方法和验收标准

Composite hollow core station post insulators for substations with a.c. voltage greater than 1 000 V and d.c. voltage greater than 1 500 V. Definitions, test methods and acceptance criteria

DIN IEC/TS 60815-3:2016 污染条件下用高压绝缘子的选择和定尺寸.第3部分:交流系统用聚合体绝缘子(IEC/TS 60815-3-2008)

Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems (IEC/TS 60815-3:2008)

DIN IEC/TS 60815-2:2016 污染条件下用高压绝缘子的选择和定尺寸.第2部分:交流系统用陶瓷和玻璃绝缘子(IEC/TS 60815-2-2008)

Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems (IEC/TS 60815-2:2008)

BS EN 61466-1:2016 标称电压大于 1000 V 的架空线路用复合串绝缘子单元 标准强度等级和端部配件

Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V. Standard strength classes and end fittings

DIN EN 62231-1:2016 交流电压大于1000 V小于等于245 kV的变电站用复合固定柱形绝缘子.第1部分:尺寸,机械和电气特性(IEC 62231-1-2015).德文版本EN 62231-1-2016

Composite station post insulators for substations with AC voltages greater than 1000 V up to 245 kV - Part 1: Dimensional, mechanical and electrical characteristics (IEC 62231-1:2015); German version EN 62231-1:2016

DL/T 1581-2016 直流系统用盘形悬式瓷或玻璃绝缘子金属附件加速电解腐蚀试验方法

Accelerated electrolytic corrosion test method for metal accessories of disc suspension porcelain or glass insulators for direct current systems

DL/T 1058-2016 交流架空线路用复合相间间隔棒技术条件

本标准规定了交流架空线路用复合相间间隔棒的型号、一般技术要求、标志、检验规则、包装和运输。 本标准适用于标称电压500kV及以下电压等级的交流架空线路用复合相间间隔棒。安装地点的海拔为1000m以下，环境温度在-40℃~+40℃之间。 500kV以上电压等级的复合相间间隔棒可参照本标准执行。

Technical specification of polymer phase to phase spacer for a.c. overhead lines

DL/T 1579-2016 棒形悬式复合绝缘子用端部装配件技术规范

Technical specification for end fittings for rod suspension composite insulators

DL/T 1580-2016 交、直流棒形悬式复合绝缘子用芯棒技术规范

本部分规定了交、直流棒形悬式复合绝缘子用芯棒的技术要求、检验规则、试验方法、包装与运输等。 本部分适用于交、直流系统架空线路、变电站或换流站用棒形悬式复合绝缘子、相间复合绝缘子(以下简称绝缘子)。

Technical specification for core of long rod composite insulators for a. c. or d. c. systems

BS EN 62231-1:2016 交流电压大于1000 V小于等于245 kV的变电站用复合固定柱形绝缘子.尺寸,机械和电气特性

Composite station post insulators for substations with AC voltages greater than 1 000 V up to 245 kV. Dimensional, mechanical and electrical characteristics

BS EN 50180-3:2015 充液变压器用1 kV至52 kV和250 A至3.15 kA的套管. 套管固定要求

Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformers. Requirements for bushing fixations

BS EN 50180-1:2015 充液变压器用1 kV至52 kV和250 A至3.15 kA的套管. 套管的通用要求

Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformers. General requirements for bushings

BS EN 50180-2:2015 充液变压器用1 kV至52 kV和250 A至3.15 kA的套管. 套管部件要求

Bushings above 1 kV up to 52 kV and from 250 A to 3,15 kA for liquid filled transformers. Requirement for bushing components

DL/T 1471-2015 高压直流线路用盘形悬式复合瓷或玻璃绝缘子串元件

本标准规定了高压直流线路用盘形悬式复合瓷或玻璃绝缘子串元件的型号及结构尺寸、技术要求、检验规则、试验方法、验收、包装、运输和储存。 本标准适用于标称电压高于1500V的直流架空电力线路用盘形悬式复合瓷或玻璃绝缘子（以下简称绝缘子）。

Cap and pin suspension ceramic or glass string insulators unit with composite shed for high voltage d.c. systems