K54 汽轮机及其辅助设备 标准查询与下载

ASME PTC 6-1976 汽轮机

Steam turbines

DIN 1943:1975 汽轮机热验收试验(VDI汽轮机规则)

Thermal acceptance tests of steam turbines (VDI rules of steam turbines)Diese Norm wurde vom Ausschu? Dampfturbinenregeln der VDI-Gesellschaft Energietechnik bearbeitet.

Thermal acceptance tests of steam turbines

JB/T 1329-1991 汽轮机与汽轮发电机 连接尺寸

本标准规定了汽轮机与汽轮发电机连接尺寸。 本标准适用于0.75～600MW固定电站凝汽式汽轮发电机组。

Connection size of steam turbine and steam turbine generator

ASME PTC 19.11-1970 装置和仪器.第11部分:动力循环中的水和蒸汽(纯度和质量.泄漏检验和测量)

Instruments and apparatus - Part 11: Water and steam in the power cycle (puritiy and quality, leak detection and measurement)

ASME PTC 20.3-1970 汽轮发电机组用压力控制系统

The purposes of this Code are: 1.01 To establish guiding principles and provide a format for performance specifications for pressure control systems applicable to the equipment covered under this Code. 1.02 To establish test procedures for determining performance characteristics of the subject pressure control systems including: 1.02.1 Pressure set point range. 1.02.2 Rate of change of pressure set point. 1.02.3 Steady state pressure regulation. 1.02.4 Transient response characteristics. 1.02.5 Steady state frequency response. 1.02.6 Dead band and hysteretic error. 1.02.7 Stability band. 1.02.8 Interaction between the variables in a compound control system. 1.03 To establish a procedure for describing the system performance by means of test quantities obtained under Par. 1.02 and the system transfer functions.

Pressure control systems used on steam turbine-generator units

DIN 4305-2:1968 汽轮机.冷凝设备组件与零件术语

Steam turbines, terms of assemblies and parts of the condenser system

Steam turbines; terms of assemblies and parts of the condenser system

DIN 4305-1:1968 蒸汽轮机.涡轮机组件和零件术语

Steam turbines, termes of assemblies and parts of the turbineDiese Norm gilt für Axial- und Radialturbinen. Bauteile von Radialturbinen, die sich wesentlich von denen der Axial-turbinen unterscheiden, sind besonders genannt und erl?utert.Die hier aufgef

Steam turbines; terms of assemblies and parts of the turbine

ASME PTC 20.2-1965 汽轮发电机组用超速自动分离系统

0.01 This Code is applicable to steam turbine generator units of 500 kw and larger and provides: 0.01.1 Recommended specifications for the performance of overspeed trip systems subject to modifications by mutual agreement between the parties concerned and 0.01.2 Standard procedures for acceptance tests to determine the performance of overspeed trip systems. The purposes of this Code are: 1.01 To establish guiding principles and specifications for overspeed trip systems that will apply to the equipment covered under this Code. 1.02 To establish test procedures to determine the following characteristics of overspeed trip systems: 1.02.1 Setting of overspeed trip 1.02.2 Short term deviation of trip speed. 1.02.3 Long term deviation of trip speed. 1.02.4 Signal transmission delay time. 1.02.5 Emergency stop valve(s) closing time. 1.03 To determine over all system performance from data obtained under Par 1.02.

Overspeed Trip Systems Of Steam Turbine-Generator Units (PTC 20.2 - 1965)

ASME PTC 6S-1988 性能测试规程.蒸汽涡轮机例行测试简化程序

The test procedures of this Report are intended for periodic turbine tests and do not supplant the Code (PTC 6) as the basic procedure for turbine acceptance tests. The Code is used for the accurate testing of steam turbines to obtain performance level with minimum uncertainty. Sections 3 through 5 of this Report present general recommendations for instrumentation and test planning. These recommendations are based on current industry practice for the periodic determination of turbine-cycle performance. Section 6 discusses interpretation of test results and shows typical plots of test data for analysis of turbine performance. Sections 7 through 12 present test procedures for selected types of turbine cycles. Each of these procedures contains specific recommendations for instrumentation and method for testing a selected turbine type.

Performance Test Code - Steam Turbines, Simplified Procedures for Routine Tests

ASME PTC 6R-1985 汽轮机运行试验中测量不确定度的评定导则

This Report provides guidance for the parties to the test to establish the degree of uncertainty of the test results when there are deviations from requirements of PTC 6 (The Code). This Report does not contain a complete test procedure. It should be used only in conjunction with the Code. Compliance with the Code is expected where no alternative is shown in this Report. Numerical values have been assigned to the uncertainty of instruments of various qualities. These numerical values, representing the consensus of knowledgeable professional people, cover 95% uncertainty intervals and therefore will be exceeded, on average, in one instance in 20.

Guidance for Evaluation of Measurement Uncertainty in Performance Tests of Steam Turbines