K54 汽轮机及其辅助设备 标准查询与下载

JB/T 9627-1999 汽轮机组成套供应范围

　　本标准规定了汽轮机组成套供应范围。 本标准适用于发电用的汽轮机组，其它用途的汽轮机组也可参考使用。

Scope of supply of steam turbine sets

JB/T 8188-1999 汽轮机随机设备供应范围

　　本标准规定了汽轮机随机备品、备件的供应范围。 本标准适用于固定式发电用汽轮机和工业汽轮机随机备品、备件的供应范围。

Scope of spare parts supplied by manufacturer with steam turbine

JB/T 8184-1999 汽轮机低压给水加热器 技术条件

　　本标准规定了汽轮机低压给水加热器(简称低加)的性能和制造技术要求。适用于火力发电厂汽轮机回热系统中管侧设计压力不高于 4.5MPa，设计温度不高于 220℃；壳侧设计压力不高于 1.5MPa，设计温度不高于 400℃ 的表面式低压给水加热器，也适用于相同工作条件的其它热交换器。

Specifications for steam turbine low pressure feed water heaters

JB/T 8990-1999 大型汽轮发电机定子端部绕组模态试验分析和固有频率测量方法及评定

本标准规定了大型汽轮发电机定子端部绕组模态试验分析和固有频率的测量方法及评定准则。 本标准适用于额定功率300 MW及以上的额定转速为3000 r/min和3600 r/min的大型汽轮发电机(包括在空冷、双水冷、全氢冷和水氢冷等)定子端部绕组的模态试验分析和固有频率测量及评定。 大型汽轮发电机在制造厂内做型式试验时，应做定子端部绕组模态试验分析。在电厂做固有频率测量时，如果发现多数线棒有接近电磁干扰力频率的固有频率时，也要做模态试验分析。 大型汽轮发电机产品在出厂前、大修后必须做定子端部绕组的固有频率测量。在电厂，有异常情况时(例如，承受突然短路、线圈磨损或者松动等)，都必须做固有频率测量。 300 MW以下的汽轮发电机，根据具体情况决定在大修后是否做固有频率测量。 进口机组也可参照此标准执行。

Model test analyses and natural frequency measurement methods of large turbo - generators on stator end windings and evaluation criteria

JB/T 9559-1999 工业汽轮机用挠性联轴器

　　本标准规定了工业汽轮机用齿式联轴器、膜片式联轴器等挠性联轴器的设计、承载零件的材料、制造质量的控制，检验和选用等基本要求。 本标准适用于工业汽轮机等中、高速机械联接两轴、传递运动和动力并对所联两轴轴线间相对的轴向、径向和角向位移需有一定补偿性能的场合。

Flexible coupling for industrial steam turbine

JB/T 9629-1999 汽轮机承压件 水压试验技术条件

　　本标准规定了汽轮机需要进行水压试验的主要部件、水压试验要求和试验结果的判定。 本标准适用于汽轮机承压件的水压试验。

Hydrostatic tests for steam turbine pressure parts

JB/T 9628-1999 汽轮机叶片 磁粉探伤方法

　　本标准规定了汽轮机叶片的湿法磁粉探伤。 本标准适用于检测叶片表面及近表面的裂纹、发纹及其它缺陷。

Method of magnetic particle inspection of steam turbine blades

JB/T 4058-1999 汽轮机清洁度

　　本标准规定了汽轮机零部件非机械加工表面清洁度分级和铸件、冷作焊接件、机械加工零部件、汽轮机油系统和蒸汽系统的清洁度。 本标准适用于汽轮机铸件、冷作焊接件、机械加工零部件、汽轮机油系统和蒸汽系统零部件清洁度的有关要求。

Standard of cleanliness for steam turbines

JB/T 4274-1999 汽轮机隔板.挠度试验方法

　　本标准规定了隔板挠度试验装置的要求、试验步骤、试验结果的判定、试验报告的内容等。 本标准适用于冲动式汽轮机的隔板挠度试验。

Deflection test of diaphragms of steam turbines

ANSI/ISA 77.42.01-1999 火电厂给水控制系统.滚筒式

The standard is intended to assist in the development of design specifications covering the measurement and control of feedwater systems in boilers with steaming capacities of 200, 000 lb/h (25 kg/s) or greater. The safe physical containment of the feedwater shall be in accordance with applicable piping codes and standards and is beyond the scope of this standard.

Fossil Fuel Plant Feedwater Control System - Drum Type

ANSI/ISA 77.13.01-1999 火电厂汽轮机旁路系统

Establishes the applicable code requirements and boundaries for the design and installation of instrument-sensing lines interconnecting nuclear safety-related power plant processes with both nuclear safety-related and non-nuclear safety-related instrumentation. Covers design, protection, and installation of nuclear safety-related instrument sensing lines for light water-cooled nuclear power plants and covers the pressure boundary requirements for sensing lines up to and including 1-inch (25.4-mm) outside diameter or three-quater-inch nominal pipe.

Fossil Fuel Power Plant Steam Turbine Bypass System

DIN EN 45510-5-1:1998 发电厂设备的购置说明.第5-1部分:蒸汽轮机

The document gives guidance on writing the technical specification for the procurement of steam turbines to be installed in electrical power plants.

Guide for procurement of power station equipment - Part 5-1: Steam turbines; German version EN 45510-5-1:1998

BS EN 45510-5-1:1998 发电站设备采购指南.正蒸汽轮机

This standard gives guidance on writing the technical specification for the procurement of steam turbines driving generators for use in electricity generating stations (power stations). This Guide for procurement is not applicable to equipment for use in the nuclear reactor plant area of nuclear power stations. Other possible applications of such equipment have not been considered in the preparation of this Guide. This Guide covers: - reheat and non-reheat turbine; - back-pressure turbine whose exhaust will be used for process heating; - condensing turbine whose exhaust is directly connected to a condenser ; - mixed pressure turbine; - regenerative cycle turbine; - extraction turbine; - combined cycle turbine. This Guide for procurement of steam turbines has been prepared to be used with the existing European Standard EN 60045-1, it should, therefore, be read in addition and complementary to the European Standard. The equipment covered by this Guide is defined by its function rather than design type. Therefore, the guidance to the specification is stated in performance terms rather than being specified by a detailed description of the equipment to be supplied. This Guide indicates to potential purchasers how their specification should be prepared so that: - the equipment type and capacity interfaces correctly with other elements of the systems; - predicted performance is achieved; - ancillary equipment is properly sized; - reliability, availability and safety requirements are achieved; - proper consideration is given to the evaluation process and the quality measures to be applied. This Guide does not determine the type of specification (e.g. detailed, performance, functional) or the extent of supply for any given contract which is normally decided on the basis of the purchaser's project strategy. It does not cover: - any commercial, contractual or legal issues which are normally in separate parts of an enquiry; - any allocation of responsibilities which are determined by the contract. This Guide does not prescribe the arrangement of the documents in the enquiry. NOTE As a comprehensive European environmental policy is still under preparation, this Guide does not address the environmental implications of the equipment.

Guide for the procurement of power station equipment - Steam turbines

DL/T 650-1998 大型汽轮发电机自并励静止励磁系统.技术条件

Specification for potential source static exciter systems for large turbine generators

ASTM D4248-98 蒸气涡轮发电机润滑油系统设计的标准实施规范

1.1 This practice is applicable to steam turbine-generator units and provides recommended practices for the design of the oil system. 1.1.1 The oil system is defined as that assembly which uses and circulates the turbine-generator lubricating oil. The oil system generally includes high pressure, bearing, control, generator seal, and drain systems. The system may also include the supply and return lines for a boiler feed pump and hydraulic coupling. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Design of Steam Turbine Generator Oil Systems

ASTM D4248-98(2003) 蒸气涡轮发电机润滑油系统设计的标准实施规范

The purpose of this guide for turbine generator oil systems is to ensure that: 3.1.1 Lubrication, control, and sealing will be performed satisfactorily by the oil in a manner mutually acceptable to the parties concerned. 3.1.2 Installation, cleaning, and flushing will be facilitated. 3.1.3 Satisfactory system cleanliness can be maintained. 3.1.4 Safe practices are observed.1.1 This practice is applicable to steam turbine-generator units and provides recommended practices for the design of the oil system.1.1.1 The oil system is defined as that assembly which uses and circulates the turbine-generator lubricating oil. The oil system generally includes high pressure, bearing, control, generator seal, and drain systems. The system may also include the supply and return lines for a boiler feed pump and hydraulic coupling.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Design of Steam Turbine Generator Oil Systems

JB/T 50086-1997 汽轮机可靠性评定规范（内部使用）

JB/T 50086-1997 本标准非等效采用美国 ANSI/IEEE Std-762《统计评价发电设备可靠性、可用性和生产能力的术语定义》等标准。本标准在技术内容上与 JB/T 7518-94 的要求基本一致。 本标准规定了汽轮机固有可靠性的评定方法、评定指标值等。 本标准适用于汽轮机固有可靠性的评定。

Steam turbine reliability assessment specification (internal use)

DL/T 609-1996 300MW级汽轮机运行导则

Guide for 300MW grade steam turbine operation

DL/T 608-1996 200MW级汽轮机运行导则

Guide for 200MW grade steam turbine operation

ASME PTC 19.11-1997 动力循环中水和蒸汽的取样、状态调节和分析

The Object of this Document is to specify and discuss the methods and instrumentation for testing boiler make-up and feedwater, steam, and condensate in relation to performance testing as may be required in Performance Test Codes in one-time acceptance testing and in continuous performance monitoring. This Document also provides guidance to power plant management, engineers, chemists, and operators in the design and operation of sampling systems for monitoring of cycle chemistry. The methods and equipment recommended herein may be useful for monitoring other influent and effluent streams of the power plant. Contamination of the stream and water cycle must be at or less than the maximum specified for the performance test before a turbine, condenser, or deaerator performance test is made.

Steam and water sampling, conditioning, and analysis in the power cycle