K54 汽轮机及其辅助设备 标准查询与下载

DL/T 607-1996 汽轮发电机漏水、漏氢的检验

Test on water leakage or hydrogen leakage of Steam-turbine Generator

JB/T 1582-1996 汽轮机叶轮锻件超声波探伤方法

本标准规定了用直射法对叶轮锻件进行接触式脉冲反射超声波探伤的各种检验程序、缺陷信号的分类、缺陷的测量与记录、探伤报告等内容。 本标准适用于JB/T 1266和JB/T 7028中各类叶轮锻件的超声波探伤，其他轮盘锻件可参考使用。 只要在订货合同上规定锻件按本方法进行超声波检查时，则要采用本方法。

Ultrasonic flaw detection of impeller forgings of turbine

JB/T 1581-1996 气轮机、汽轮发电机转子和主轴锻件超声波探伤方法

本标准对汽轮机、汽轮发电机转子和主轴锻件超声波探伤人员、探伤器材、探伤操作要领和探伤结果记录评定等内容作了规定。 本标准适用于JB/T 7025、JB/T 1265、JB/T 7027以及JB/T 7026、JB/T 1267、JB/T 7178中各类转子和主轴锻件的超声波探伤。其他各种工况件类似的轴类锻件可参考使用本标准。 本标准适用于采用脉冲反射超声波探伤原理对转子和主轴锻件外圆面进行纵波接触法超声波探伤。

Ultrasonic flaw detection of rotor and main shaft forgings of the turbine and turbogenerator

BS EN 60953-2:1996 汽轮机热试验规则.汽轮机的尺寸和各种类型精度的大范围

The rules given in this standard are applicable to thermal acceptance tests covering a wide range of accuracy on steam turbines of every type, rating and application. Only the relevant portion of these rules will apply to any individual case. The rules provide for the testing of turbines, whether operating with either superheated or saturated steam. They include measurements and procedures required to determine specific enthalpy within the moisture region and describe precautions necessary to permit testing while respecting radiological safety rules in nuclear plants. Uniform rules for the preparation, carrying out, evaluation, comparison with guarantee and calculation of measuring uncertainty of acceptance tests are defined in this standard. Details of the conditions under which the acceptance test shall take place are included. Should any complex or special case arise which is not covered by these rules, appropriate agreement shall be reached by manufacturer and purchaser before the contract is signed.

Rules for steam turbine thermal acceptance tests - Wide range of accuracy for various types and sizes of turbines

BS EN 60953-1:1996 蒸汽轮机热验收试验规则 大型凝汽式汽轮机的高精度

The rules given in this standard are applicable primarily to thermal acceptance tests with high accuracy for condensing steam turbines driving generators for electric power services. Some of the provisions of these rules are relevant to turbines for applications other than driving electric power generators. These rules provide for the testing of turbines operating with either superheated or satu-rated steam. They include measurements and procedures required to determine specific enthalpy within the moisture region and describe precautions necessary to permit testing while respecting radiological safety rules in nuclear plants. These rules contain information also applicable to the testing of back-pressure turbines, extraction turbines and mixed-pressure turbines. Only the relevant portion of the rules need apply to any individual case. Uniform rules for the preparation, carrying out and evaluation of the acceptance tests are defined in this standard. Details of the conditions under which the acceptance tests shall take place are included. Should any complex or special case arise not covered by these rules, appropriate agreement shall be reached by manufacturer and purchaser before the contract is signed.

Rules for steam turbine thermal acceptance tests. High accuracy for large condensing steam turbines

JB/T 8191-1995 水轮机调速器与油压装置.术语

本标准规定了水轮机调速器与油压装置专业的专业术语及其定义。 本标准适用于制订标准、编订技术文件，也适用于编写和翻译专业手册、教材及书刊。

Terminology of speed governor and oil pressure supply unit for hydraulic turbine

ASME PTC 6S REPORT ERTA-1996 ASME PTC 6S报告勘误表.1988 (R 1995)

The Errata corrections listed below apply to ASME PTC 6.5 Report- 1988 (R 1995). hoceduresfor Routine Performance Tests of Steam Turbines.

Errata to ASME PTC 6s REPORT-1988 (R 1995)

DL/T 590-1996 火力发电厂固定式发电用凝汽汽轮机的热工检测控制技术导则

Directives of thermal instrumentation and control for condensation type turbine in power plant

DL/T 591-1996 火力发电厂汽轮发电机的热工检测控制技术导则

Directives of thermal instrumentation and control for turbo-generator in power plant

ASME PTC 6-1996 汽轮机

Steam turbines

HB 7258-1995 轻型燃气轮机成套设备产品标准编写基本规定

本标准规定了轻型燃气轮机成套设备（以下简称“燃机设备”）产品标准编写的基本要求，标准的构成及要求。 　　本标准适用于编写燃机设备产品标准。

Basic regulations for compiling product standards of light-duty gas turbine complete sets of equipment

HB 7257-1995 轻型燃气轮机进气过滤器

本标准规定了轻型燃气轮机的进气过滤要求，针对不同的工作环境推荐不同类型的进气过滤器；并对各类进气过滤器的性能、产品检验要求及其性能试验方法提出了技术要求。 　　本标准适用于陆基固定型轻型燃气轮机成套设备（以下简称燃机设备）所采用的进气过滤器。本标准是供需双方进行技术协商的依据。

Light Duty Gas Turbine Intake Filters

HB 7120-1994 轻型燃气轮机气体燃料使用技术要求

本标准规定了轻型燃气轮机气体燃料的选用原则和基本要求。本标准是轻型燃气轮机采购和供需双方进行技术协商所必需的资料之一。 　　本标准适用于工业驱动和发电用轻型燃气轮机。

Technical requirements for the use of gas fuel for light gas turbines

JIS B 8102:1995 汽轮机.验收试验

Steam turbines -- Acceptance test

NF C55-564*NF EN 61064:1993 汽轮机速度控制系统的验收试验

Acceptance tests for steam turbine speed control systems.

JB/T 3073.5-1993 汽轮机用铸造静叶片.技术条件

本标准规定了汽轮机用铸造静叶片、喷咀的技术要求和检验规则。 本标准适用于汽轮机用铸造静叶片，喷咀的毛坯及成品。

Casting stationary blade of turbine - Specification

JB/T 3344-1993 凝汽器性能试验规程

本标准规定了汽轮机凝汽器性能试验方法，用以确定凝汽器下列性能指标： a.凝汽器在设计工况下（排气量、冷却水流量、冷却水进口温度、总体清洁系数均为设计值）的热力特性； b.凝汽器在设计工况下的热力特性； c.凝汽器凝结水的过冷度； d.凝汽器凝结水的含氧量； e.凝汽器的水阻特性。 本标准适用于汽轮机表面式凝汽器性能试验。

Performance testing code of condensers

JB/T 6765-1993 特种用途工业汽轮机技术条件

本标准规定了特种用途工业汽轮机的主要性能指标和本体结构及辅助设备的基本要求。 本标准适用于特种用途工业汽轮机。

Specification of industrial turbine for special purpose

JB/T 6764-1993 一般用途工业汽轮机技术条件

本标准规定了一般用途工业汽轮机的主要性能指标和本体结构及辅助设备的基本要求。 本标准适用于一般用途工业汽轮机。

Specification of industrial turbine for general purpose

BS EN 61064:1993 汽轮机调速系统验收试验指南

Guidance to tests on speed governing and overspeed protection systems to verify manufacturers guarantees eg. compliance with BS EN 60045-1.

Guide to acceptance tests for steam turbine speed control systems